Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for HITEC X1-200 Touch
Summary of Contents for HITEC X1-200 Touch
- Page 1 INSTRUCTION MANUAL...
-
Page 2: Table Of Contents
Volt Meter .........................22 Memory Presets - Data Store/Load .................23 Hitec RCD USA will not be held responsible for any damages or injuries that 1. Storing Presets ....................23 may occur by persons who fail to follow these warnings or who fail to prop- 2. -
Page 3: Introduction
INTRODUCTION (cont.) SPECIFICATIONS AND CHARGER LAYOUT Specifications Congratulations on your choice of the Hitec X1-200 Touch digital, intelligent touch screen interface charger from Hitec RCD USA. The Hitec X1-200 Touch is DC Input 11-18 Volt DC Charge circuit power 55 Watts... -
Page 4: Features
Dual Power Input continuous charging or discharging. The X1-200 Touch has the ability to operate on a variety of power sources. The Users can call out this data at any time without any special program setting. power source can be a 12 volt automotive-type battery, an 11 ~ 18 volt DC power supply, or a 100 ~ 240 volt AC household current. -
Page 5: Warnings And Safety Notes
Hitec Charge Master Software - Batteries installed in a device or which are electrically linked to other The free “Hitec Charge Master” software gives you unparalleled ability to operate the components charger through the computer. You can monitor pack voltage, cell voltage and other... -
Page 6: Power Supply Connections
Before charging your batteries, it is critical that you determine the maximum allowable POWER SUPPLY CONNECTIONS charge rate for your batteries. The X1-200 Touch is capable of charging at high rates that may not be suitable or safe for your particular batteries. For example, Lithium cells are typically safe to charge at 1C, or the total mAh÷1000. -
Page 7: Programing Interface
When you power up the charger, you will see the following screen. This is Browse - Touch the arrows ▲ AND ▼ or ◄ AND ► to browse the selections. the Main Menu (HOME) screen of the X1-200 Touch charger. Select - Touch your selection on the screen for confirmation. -
Page 8: Safety Protection
You can set the maximum charge time as a backup in the event the SAFETY This is the voltage level at which the X1-200 Touch will stop charging the LiPo 4.18 - 4.3V/Cell 1-720 Minutes X1-200 Touch is unable to detect the proper charge cut off conditions. -
Page 9: Charger Operations
Using the Balance Socket The X1-200 Touch package includes our Universal Balancing Board that ac- comodates most popular balancing connections. Plug the balancing board into the charger as shown below, then plug the battery into the proper socket on the balancing board, making sure the polarity is correct. -
Page 10: Charging Program
CHARGER OPERATIONS (cont.) CHARGER OPERATIONS (cont.) 2. CHARGING PROGRAM 3. PROGRAM START The available program modes are dependent on the battery type used. The Touch the start button or touch and hold the framed Operation Program chart below lists the different operations available for each type of battery. for 3 seconds to start the program. -
Page 11: Program Stop
2. GRAPH and you will be taken back to the Main Menu When the charger is operating, the The X1-200 Touch also has the abil- user can easily check the real-time ity to display the total pack voltage status of the charging capacity, cell... -
Page 12: Using The Charge Master Charge Control Software
USING THE CHARGE MASTER CHARGE CONTROL SOFTWARE MEMORY PRESETS – DATA STORE/LOAD The X1-200 Touch charger can store up to 5 diff erent charge/discharge Visit the Hitec RCD USA (www.hitecrcd.com) website to download the free profi les for your convenience. These stored profi les can be recalled quickly CHARGE MASTER software for Windows PC’s. -
Page 13: Motor Rpm Tester
MOTOR RPM TESTER SERVO TESTER The X1-200 Touch has the ability to test the RPM of brushless motors with a The X1-200 Touch can test most digital and analog servos. To test for basic sensor port. To test the motor RPM connect the motor and ESC as follows: servo functionality, connect the servo to the X1-200 Touch as follows: 1. -
Page 14: Warranty And Service
EN55014-2 Conforms For a period of one year from the date of purchase, HITEC RCD USA, INC. shall REPAIR apparatus - Part 2: Immunity-Product family OR REPLACE, at our option, defective equipment covered by this warranty. Other-... - Page 15 www.hitecrcd.com...
Need help?
Do you have a question about the X1-200 Touch and is the answer not in the manual?
Questions and answers