Table of Contents
Advertisement
Quick Links
LCD-Kit01
640x480 – 18bits
P64CV1 LCD Display
©Copyright 1999 by ICP Electronics Inc. All Rights Reserved.
Manual first edition May01, 1999.
The information in this document is subject to change without prior
notice in order to improve reliability, design and function and does
not represent a commitment on the part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect,
special, incidental, or consequential damages arising out of the use
or inability to use the product or documentation, even if advised of
the possibility of such damages.
This document contains proprietary information protected by
copyright. All rights are reserved. No part of this manual may be
reproduced by any mechanical, electronic, or other means in any
form without prior written permission of the manufacturer.
Advertisement
Table of Contents
Related Manuals for ICP Electronics LCD-Kit01
Summary of Contents for ICP Electronics LCD-Kit01
- Page 1 LCD-Kit01 640x480 – 18bits P64CV1 LCD Display ©Copyright 1999 by ICP Electronics Inc. All Rights Reserved. Manual first edition May01, 1999. The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer.
-
Page 2: Table Of Contents
Specifications.................. 3 What You Have................4 2. Installation................5 Welcome to the LCD-Kit01 – P64CV1. The LCD-Kit01 is high brightness Amorphous Silicon TFT LCD panel with 640 x 480 LCD-01 Connection Board Layout ..........5 resolution and 18-bits display colors. It is compatible with VGA- LCD-Kit01 Connection Layout............ -
Page 3: Specifications
1.1 Specifications : 1.2 What You Have In addition to this User's Manual, the LCD-Kit01 package includes Supply Voltage : +5V the following items: Panel Size : 6.4” (17cm) Diagonal • one P64CV1 6.4” LCD Panel with its mounting kit Display Active Area Size : 129.60mm (H) x 97.44mm (V) -
Page 4: Installation
LCD-Kit01 Connection Layout Installation This chapter describes how to install the LCD-Kit01. The layout of LCD-01 Connection Board is shown on the next page and the Unpacking Precautions that you should be careful with are described on the following page. Also included is the jumpers, connectors and switches setting for this LCD-Kit01. -
Page 5: Unpacking Precautions
Disconnect power supply before handling and doing connection on setting LCD-Kit01. Do not plug any connector or jumper while the power is on. It will cause fatal damage to your LCD panel. Make sure that every connector is connected in correct direction. -
Page 6: Backlight Inverter Control
FPVEE • CN4: 22x2 Header/2.0mm LCD Connector (connect to LCD Control Card) PIN NO FUNCTION PIN NO FUNCTION +12V +12V FPVEE SHFCLK ENBKL LCD-Kit01 640 x 480 / 18 bits LCD-Kit01 640 x 480 / 18 bits P64CV1 P64CV1... - Page 7 C-VR1 C-VR2 R/L * U/D * Note:1. * the same function as CN7 2. Choose only one of CN8 or CN7 to be used. LCD-Kit01 640 x 480 / 18 bits LCD-Kit01 640 x 480 / 18 bits P64CV1 P64CV1...
-
Page 8: Backlight Connector
PM-1035 DC to DC Module under the situation where the distance between your SBC and LCD display is 70cm ~ 2m. Visit www.icpacquire.com.tw for more information on PM-1035. LCD-Kit01 640 x 480 / 18 bits LCD-Kit01 640 x 480 / 18 bits P64CV1 P64CV1... -
Page 9: Voltage And Bios Setting
Kit01. These settings are done on your SBC. LCD&CRT Selection : Auto or Both LCD Type : #6 640x480 18bit Voltage Setting The Supply Voltage for LCD-Kit01 is +5V. You must set the LCD JUKI-745E Peripheral Setup: JP39: 2-3 > ON Voltage Setting Jumper on your SBC to +5V. -
Page 10: Bios Setting For Sbcs With Hm86508 Chipset
2. U/D is for picture horizontal rotation 3. R/L is for picture vertical rotation 4. Don’t change the ‘system internal setting’ LCD-Kit01 640 x 480 / 18 bits LCD-Kit01 640 x 480 / 18 bits P64CV1 P64CV1...