Copyright Notice This document and product are copyrighted, September 2001, by ICP Electronics Inc. All rights are reserved. No part of this manual may be reproduced, copied, or translated without prior notice to ICP Electronics Inc. The information provided in this document is for reference only. We do not assume any responsibility arising out of the application of the products.
IEI LCD monitor brings information everywhere. Even under the most severe environments like steel plant or warehouse, DM/SRM series offer multiple mounting options and brightness that meet your needs. The DM-121/ SRM-121 is a 12.1" flat panel display specially designed to meet the applications for industrial environment.
Page 6
Power supply: (DM-121) Model no: UP06031120A Input requirements: Input Voltage range: 90 to 264 VAC. Line frequency: 47 to 63 HZ. In-Rush current: 80 A max. Input current: 1.4 A max. Output: Output Voltage range: +11.4V ~+12.6V (tolerance: ¡Ó5%) 3.8A 45 Watt...
Page 7
Power supply: (SRM-121) Model no: PSA65U-120 Input requirements: Input Voltage range: 90 to 264 VAC. Line frequency: 47 to 63 HZ. In-Rush current: 30A max@115VAC ,60A max@230VAC at 25¢J . Input current: 1.5 A max@115VAC, 0.8A max@230VAC. Output: Output Voltage range: +12V ¡Ó0.5V 5A 60 Watt Ripple and Noise at Voltage 120 mvP Operating environmental conditions: Ambient Temperature: 0°C~40°C.
1.2 Product Dimensions The following diagrams indicate the dimensions of DM-121/SRM-121. Front Panel: 340mm x 260mm x 9mm (WxHxD) Cabinet: 310mm x 230mm x 43.7mm (WxHxD)… … DM-121 Cabinet: 310mm x 230mm x 56.6mm (WxHxD)… … SRM-121 SRM-121 DM-121 "*" Front panel of thickness.
Chapter 2 System Setup The DM-121/ SRM-121 is very easy to be set up for operation. As you set up your system, please refer to the following procedures. 2.1 Front panel operation LCD on/off Button Exit Button Up Button Down Button...
2.2 LCD Installation DM-121/SRM-121 provides two features for your choosing: one is LCD only; the other is LCD with touch screen. You can use VGA cable connects from LCD panel to your system VGA interface. 2.2.1 LCD without Touch Screen There are five LCD adjustment switches on the rear panel of DM-121/SRM-121.
2.2.2 LCD with Touch Screen If you want to install LCD with Touch Screen, please connect RS232 connector from LCD to your COM port from CPU card. The driver for touch screen we used the CD disk with system shipping.
2.3 Panel Mounting DM-121/SRM-121 is either suitable for panel mounting. As you mount this flat panel display, please refer to the diagram below. STEP 1 312.0 STEP 2 STEP 2 STEP 2 UNIT:mm STEP 2 THE DIMENSION IS FOR PANEL MOUNTING (The flat panel thickness is 6mm or less than 6mm) Less than 6.0mm...
2.4 Arm Mounting DM-121/SRM-121 is suitable for 75/100mm interface pads or for arm mounting. arm mounting and the specification conform to the proposed VESA standard. 75.0 100.0...
2.5 Wall Mounting DM-121/SRM-121 is suitable for wall mounting and the specification conform to the proposed. 153.00 90.00 8-D4.5 153.00 90.00 WALL-MOUNT BRACKET STEP 1 S TEP 2 SCREW BOLT Wall WALL-MOUNT VIBRATION KIT STEP 4 STEP 3 Wall...
Chapter 3 User Mode OSD Information 3.1 User Mode OSD Structure LEVEL 0 LEVEL 1 VALUE RGB Menu Brightness Press Select Button -127 ~ 127 Green -127 ~ 127 Blue -127 ~ 127 Color Temp 0 ~ 7 Sharpness 0 , 1 Main Menu Press Select Button Geometry Menu Auto-Adjustment...
3.2 User Mode OSD Item description l Auto-Adjustment This item will automatically adjust the H/V position, frequency, phase, and black level. l Auto Phase This item will automatically adjust the sampling. l Brightness It is used to adjust the brightness of screen. This function will adjust the offset value of ADC.
Page 18
l DOS/GFX It is used to choose VGA Input signal that is text mode or graphic mode. (It is only selectable on resolution of 720/640x400 or 720/640x350.) 400 and 350 standard IBM mode have the same Hsync. and Vsync. Value. AV-9261 MPU can not differentiate them automatically and users need to adjust them by manual to match proper VGA mode.
l Revert It is used to reload original parameters from the factory’s OSD data area of the system EEPROM 24c16 device to re-initialize AV-9261 system device. When users adjust OSD data too much and can not see better quality than before, users can select this item, Revert, and MPU will reload default BIOS setting and re- initialize the system.