Safety Instructions - Makita 6704D Instruction Manual

ENGLISH
1 Battery cartridge
2 Set plate
3 Charging light
4 Battery charger
5 Hole for detent pin
6 Detent pin
7 Square drive

SAFETY INSTRUCTIONS

WARNING! When
machines basic safety precautions, including the
following, should be followed to reduce the risk of
fire, leaking batteries and personal injury: Read
these instructions before operating this product
and save these instructions.
For safe operation:
1. Keep work area clean
– Cluttered areas and benches invite injuries.
2. Consider the work environment
– Do not expose the machine to rain. Keep work
area well lit. Do not use machines in the pres-
ence of flammable liquids or gases.
3. Keep children away
– Do not let visitors touch the machine. Keep visitors
away from work area.
4. Store batteries or idle machines
– When not in use, machines and batteries should be
stored separately in a dry, high or locked up place,
out of reach of children.
– Ensure that battery terminals cannot be shorted by
other metal parts such as screws, nails, etc.
5. Do not force the machine
– It will do the job better and safer at the rate for which
it was intended.
6. Use the right machine
– Do not force small machines or attachments to do
the job of a heavy duty machines. Do not use
machines for purposes not intended.
7. Dress properly
– Do not wear loose clothing or jewellery, they can be
caught in moving parts. Non-skid footwear is rec-
ommended when working outdoors. Wear protect-
ing hair covering to contain long hair.
8. Use protective equipment
– Use safety glasses and if the cutting operation is
dusty, a face or dust mask.
9. Connect dust extraction equipment
– If devices are provided for the connection of dust
extraction and collection ensure these are con-
nected and properly used.
10. Do not abuse the supply cord (if fitted)
– Never carry the machine by the cord or yank it to
disconnect from the socket. Keep the cord away
from heat, oil and sharp edges.
11. Secure the work
– Use clamps or a vice to hold the work. It is safer
than using your hand and it frees both hands to
operate the machine.
12. Do not over-reach
– Keep proper footing and balance at all times.
Explanation of general view
8 Bit with Form C 6.3 shank
9 Round drive
0 Switch trigger
q Reversing switch
w Clockwise rotation
e Counterclockwise rotation
using battery operated
r Number
t Adjusting ring
y Red mark
u Screw
i Screw
o Set plate
13. Maintain machines with care
– Keep cutting machines sharp and clean for better
and safer performance. Follow instructions for lubri-
cation and changing accessories. Inspect machine
cords periodically and if damaged have repaired by
an authorized service facility.
14. Disconnect machines
– Where the design permits, disconnect the machine
from its battery pack when not in use, before
servicing and when changing accessories such as
blades, bits and cutters.
15. Remove adjusting keys and wrenches
– Form the habit of checking to see that keys and
adjusting wrenches are removed from the machine
before turning it on.
16. Avoid unintentional starting
– Do not carry the machine with a finger on the
switch.
17. Stay alert
– Watch what you are doing. Use common sense. Do
not operate the machine when you are tired.
18. Check damaged parts
– Before further use of the machine, a guard or other
part that is damaged should be carefully checked to
determine that it will operate properly and perform
its intended function. Check for alignment of moving
parts, free running of moving parts, breakage of
parts, mounting and any other condition that may
affect its operation. A guard or other part that is
damaged should be properly repaired or replaced
by an authorized service facility unless otherwise
indicated in this instruction manual. Have defective
switches replaced by an authorized service facility.
Do not use the machine if the switch does not turn
it on and off.
19. Warning
– The use of any accessory or attachment, other than
recommended in this instruction manual, may
present a risk of personal injury.
– Ensure that the battery pack is correct for the
machine.
– Ensure that the outside surface of battery pack or
machine is clean and dry before plugging into
charger.
– Ensure that batteries are charged using the correct
charger recommended by the manufacturer. Incor-
rect use may result in a risk of electric shock,
overheating or leakage of corrosive liquid from the
battery.
20. Have your machine repaired by a qualified
person
– This machine is constructed in accordance with the
relevant safety requirements. Repairs should only
be carried out by qualified persons using original
spare parts, otherwise this may result in consider-
able danger to the user.
4