Table of Contents
Advertisement
ate tariffs.
occur in a particular installation. If
aring aid
this equipment does cause harmful
interference to radio or television
ges
or
reception, which can be determined
unit
not
by turning the equipment off and on,
the party
the user is encouraged to try to
nce could
correct the interference by one or
to operate
more of the following measures:
• Reorient or relocate the receiving
has been
antenna.
ly with the
• Increase the separation between
tal device,
the equipment and receiver.
FCC Rules.
• Connect the equipment into an
to provide
outlet on a circuit different from
against
that to which the receiver is
residential
connected.
cordless
• Consult
the
requencies
experienced radio TV technician
erence to
for help.
o minimize
rence, the
telephone
r or on top
rference is
e cordless
m the TV or
minate the
here is no
ce will not
was
not
IN NO EVENT SHALL WE BE LIABLE
riations in
FOR ANY SPECIAL, INCIDENTAL OR
and
CONSEQUENTIAL DAMAGES FOR
is product
BREACH OF THIS OR ANY OTHER
in some
WARRANTY,
EXPRESSED
tern
Bell
IMPLIED, WHATSOEVER.
tail Sales
This warranty gives you specific legal
bility
for
rights, and you may also have other
incurred
rights which vary from state to state.
his product
other than
ed.
ranty is in
warranties,
s.
ANY
RRANTIES,
ABILITIES,
MITED TO
NTIES OF
FITNESS
PURPOSE,
DURATION
ATION OF
WARRANTY.
T ALLOW
LONG AN
ASTS, SO
MAY NOT
OPERATIONS
40-Channel Operation
The FF940 cordless telephone automatically
searches and selects the clearest of 40
channels when it is being used.
Security Code
The security code prevents your cordless
telephone
accessed by a phone on a different line.
Once the handset battery is fully charged,
the handset will automatically select the
code from a total of over 65,000
combinations. The code is changed every
time the handset is placed in the cradle.
If you experience difficulty with placing or
receiving calls, a lost security code may be
dealer
or
an
the cause of the problem. When this
occurs, the handset can no longer
communicate with the base. Reset by
placing handset on base for 5-10 seconds.
If that does not work, unplug the AC
adaptor from the wall outlet. Disconnect
the handset battery for 5-10 seconds, then
reconnect. Place handset back on base
and then replug the AC adaptor.
Placing a Call
1. Press TALK button.
2. TALK BUTTON on handset will light.
3. When you hear a dial tone, open flip
and place your call.
4. While on a call, if you experience noise
or static:
a. Press CHANNEL on handset until a
OR
b. Move closer to base.
NOTE: You must be in usable range to
change channels. Base antenna should be
in upright position.
Using the Headset
1. Plug headset into headset jack on the
side of the handset.
2. Position headset comfortably on your
head.
3. Adjust speaking wand, placing it near
your mouth.
4. Place call following steps above.
5. For hands free conversation, attach the
belt clip on the back of the handset to
your clothing.
NOTE: You cannot speak through both the
handset and the headset at the same time.
You must unplug the headset in order to hear
and speak through the handset.
conversation
from
being
clear channel is found; the call will
not be interrupted.
Or
NOTE: When the headset is not in use, it
can be easily stored on the headset
hanger. The hanger can be removed from
the base if desired. To remove the hanger,
push up on the tab and pull hanger out
from base.
Receiving a Call
1. IF THE HANDSET IS OUT OF THE
BASE UNIT, press TALK.
2. IF THE HANDSET IS IN THE BASE
UNIT, lift the handset.
Do
not
press
TALK.
You
automatically be connected.
Ending a Call
1. Place the handset in the base or press
TALK to be disconnected from the line.
2. TALK BUTTON on handset will turn off.
Flash
Use the FLASH button to activate custom
calling services such as Call Waiting or
Three-Way Calling (*Special subscription
from your local telephone company
required).
Temporary Tone (*)
PULSE (rotary) service users may access
touch-tone features needed to operate
answering machines or use electronic
banking, calling cards, etc., by pressing
the
TONE
(*)
button.
Phone
automatically return to pulse dialing after
the call ends.
Out of Range
If you experience static while using the
telephone, move closer to the base or
change the channel by pressing the
channel button.
Redial
Last number dialed (up to 32 digits) is
stored in redial memory until another
number is dialed.
1. Press TALK on handset.
2. When you hear a dial tone, open flip
and press REDIAL.
will
will
Advertisement
Table of Contents
