Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Instruction Manual
MICRON HERBI-4 PERIODIC INSPECTION CHECK LIST
ITEM
PARTS NO
DESCRIPTION
1
4134A
ELECTRIC WIRE BLACK THICK / 1.28M
2
4368
ELECTRIC WIRE RED THICK - 1.32M
3
4457
SPRING 9/32" TERMINAL CONNECTING
4
4993
PVC TUBE 6MM X 9MM - 1.21M
5
5021
ATOMISER DISC
6
5022
SLINGGER DUMMY SHAFT
7
5039
FEED NOZZLE YELLOW
8
5107C (800-5107C)
NECK STRAP
9
5442
MOTOR HERBI - 4
10
5454
O - RING (BS 611)
11
5455
O - RING (BS 365-30)
12
5776B
INLINE SYPHONE TAP (NEW MODEL)
13
8381B
SHOULDER STRAP
14
MPP6021
PVC TUBE
15
8386BC
BATTERY BOTTOM COVER
16
8385H
BATTERY COVER BOTTOM SCREW
17
5000/01
WIRE HARNESS MOTOR TO SWITCH
18
5000/02
SWITCH C/W EXTENSION WIRE
19
5000/03
SUB HARNESS (FEMALE CONNECTOR)
20
AP 01R
SWITCH RED
21
BAT6V3AH
6V 3AH LEAD SEALED BATTERY
22
MPP6019
WIRE HARNESS FROM BATTERY(MALE CONNECTOR)
0
Complusory change for continuous use at indicated intervals.
The rest change when necessary.
Exclusively distributed by
RB Spray Tech Sdn Bhd
(627487-P)
Head Office
No. 44, Lorong Sanggul 1E, Bandar Puteri Klang, 41200 Klang,
Selangor Darul Ehsan, Malaysia.
Tel: 603-5162 5746, 51625745 Fax: 603-51615741
E-mail: rbst@streamyx.com; info@rbfield.com
4 MONTHS
8 MONTHS
12 MONTHS
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Manufactured by
Micron
Bromyard Industrial Estate, Bromyard,
Herefordshire, HR7 4HS, UK
Web: www.micron.co.uk
YOUR KEY TO SMART TECHNOLOGY
Instruction Manual
Advertisement
Table of Contents
Related Manuals for Micron Herbi-4 CDA
Summary of Contents for Micron Herbi-4 CDA
- Page 1 MICRON HERBI-4 PERIODIC INSPECTION CHECK LIST ITEM PARTS NO DESCRIPTION 4 MONTHS 8 MONTHS 12 MONTHS 4134A ELECTRIC WIRE BLACK THICK / 1.28M 4368 ELECTRIC WIRE RED THICK - 1.32M 4457 SPRING 9/32" TERMINAL CONNECTING 4993 PVC TUBE 6MM X 9MM - 1.21M...
-
Page 2: Table Of Contents
2,000 rpm to produce uniform spray droplets of around 250 micron; large enough to minimise any risk of spray drift. Liquid - If the atomiser disc is rubbing on the motor base plate or the motor shaft is bent. -
Page 3: Safety
Specially designed ST backpacks and a shoulder strap are available for use with the Note: HERBI-4. Acoustic information: the sound pressure level at the operator’s ear should not exceed 70 dB(A). SAFETY Vibration: the weighted RMS acceleration value at the hands when using this machine should not exceed 2.5 m/sec . -
Page 4: Mixing, Fillingand Calibration
‘risk of serious damage to the eyes’ e.g. paraquat (Gramoxone) which is classified as toxic should not therefore be used through the HERBI-4 at concentrations greater than recommended on the label. Micron do not generally recommend using spray mixes of more than ten times the maximum concentration recommended for high volume application with knapsack sprayers. - Page 5 The table below indicates the relationship between total spray volume, flow rate and walking speed for the HERBI-4 as per the following formula: Flow rate (ml/min) = 6 x total spray volume (l/ha) x walking speed (m/s) x band width (m) Total spray volume Band width Feed nozzle...
-
Page 6: Before Spraying
BEFORE SPRAYING It is best to hold the HERBI-4 to the side or the rear so that the operator does not have to walk over the treated area. Check the wind speed and direction (below 5 kph) is safest. Take special care to avoid drift by keeping the spray head as low as possible. -
Page 7: After Spraying
AFTER SPRAYING 3. After working with agrochemicals, or handling spraying equipment, always thoroughly wash hands and exposed skin. All protective clothing should be washed 1. Dispose of any surplus spray mix according to the product approval. Store products separately from other clothing and stored. Contaminated gloves should be washed safely, locked up and out of the reach of children. - Page 8 MICRON HERBI-4 SPRAYER PARTS listing ITEM PARTS NO. DESCRIPTION 3456 SCREW NO. 6 X 1/4" S/T (B) 3512/15 AIR VENT TUBE - 0.15M 4134A ELECTRIC WIRE BLACK THICK / 1.28M 4256 SPRING 5/16" O.D 4368 ELECTRIC WIRE RED THICK - 1.32M...