Page 2
SALES REPRESENTATIVE # _____________________ DEALER NAME ________________________________ OPERATIONS GUIDE NUMBER ___________________ PUBLISHED __________________________________________ Copyright 1995 Windsor Industries, Printed in USA YOUR DEALER Name: __________________________________________________________________________________________________ Address: _______________________________________________________________________________________________ For the name and address of your dealer contact: Windsor Industries Phone Number: _________________________________________________________________________________________ PRS2/PRSD2 98901 10/10/01...
Set Up and Operation ........3-1 Shut Down and Storage......3-1 MAINTENANCE Maintenance Schedule........4-1 Daily Maintenance........4-1 Periodic Maintenance.........4-1 Solution Pump Replacement......4-1 Vacuum Motor Replacement......4-1 Carbon Brush Replacement.......4-1 Machine Troubleshooting.......4-2 Wiring Diagram ..........4-2 Service Schedule...........4-3 PRS2/PRSD2 98901 06/28/03...
SERIAL NO. FROM – column indicates Parts may be ordered from authorized Windsor the first machine the part number is dealers. When placing an order for parts, the applicable to. When the machine design...
Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not pull/run machine over cord. Keep cord away from heated surfaces. Connect to a properly grounded outlet. See Grounding Instructions. SAVE THESE INSTRUCTIONS PRS2/PRSD2 98901 10/19/02...
Unless Operation Guide is Read and understood. In Flammable or Explosive areas. In areas with possible falling objects. WHEN SERVICING MACHINE: Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the machine. Use manufacturer approved replacement parts. PRS2/PRSD2 98901 10/19/02...
The green colored rigid ear, lug, or wire extending from the adaptor must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adaptor is used, it must be held in place by a metal screw. PRS2/PRSD2 98901 10/19/02...
CARPET FOR COLOR freeze during storage and crack internal . Also, to avoid FASTNESS IN AN INCONSPICUOUS PLACE components, causing damage to the unit. prolonged drying times, do not spray too much solution in any one area. PRS2/PRSD2 98901 10/19/02...
Remove and clean jets Little or no solution flow tool Check and replace pump. Faulty pump (Call Windsor Tech. Services first) Incorrectly attached solution Ensure solution hose coupler is securely attached to the hose coupler on the solution tank. Ensure vac hose is pushed completely onto the recovery...
Check vacuum intake screen for damage; replace if necessary Check pump pressure; observe spray pattern and check with gauge if necessary Check and clean solution screen Check cables for fraying Check overall performance of machine Check vac motor carbon brushes PRS2/PRSD2 98901 10/19/02...
Page 12
RECOVERY TANK PARTS PARTS INSIDE PORTAL CAP PRS2/PRSD2 98901 06/28/03...
LABELS & PARTS LIST SERIAL NO. PART NO. DESCRIPTION NOTES: FROM 500009 LABEL, WARNING 500528 LABEL, WINDSOR MAIN 500529 LABEL, WINDSOR LOGO 6 X 1.75 50776 LABEL, FOR SAFETY 500480 LABEL, ON/OFF VAC/PUMP PRS2/PRSD2 98901 01/15/02...
The Machine Registration Card must be completed and returned immediately at the time of purchase. If proof of purchase cannot be identified, the warranty start date is 90 days after the date of sale to an authorized Windsor distributor. Parts replaced or repaired under warranty are guaranteed for the remainder of the original warranty period.
Page 22
If difficulty develops during the warranty period, contact the authorized Windsor agent from whom the product was purchased. Windsor Industries, Inc. may elect to require the return of components to validate a claim. Any defective part to be returned must be shipped freight prepaid to an authorized Windsor Distributor/Service Center or to the Windsor factory.
Need help?
Do you have a question about the Presto! PRS2 and is the answer not in the manual?
Questions and answers