Table of Contents
Advertisement
68
EN
Programme
N I
OUT
MODE
1
– –
– – : – – ~
2
~
3
~
4
~
5
~
6
~
7
~
8
~
T
M I
E CODE
– – : – –
TOTAL
0
0 : 00
Remote sensor
FADE/WIPE
EFFECT
EDIT IN/OUT
CANCEL
Fader And Wipe Menu (available only for
Random Assemble Editing)
You can also use the fade/wipe effects on page 37.
DISSOLVE
The new scene gradually appears as the old one
gradually disappears.
WIPE — CORNER
The new scene wipes in over the previous one from
the upper right corner to the lower left corner.
WIPE — WINDOW
The next scene gradually wipes in from the centre of
the screen toward the corners, covering the previous
scene.
WIPE — SLIDE
The next scene gradually wipes in over the previous
one from right to left.
WIPE — DOOR
The previous scene wipes out from the centre to the
right and left, like a door being pushed open to reveal
the next scene.
WIPE — SCROLL
The new scene wipes in over the last one from the
bottom of the screen to the top.
WIPE — SHUTTER
The new scene wipes in over the previous one from
the centre toward the top and bottom of the screen.
USING THE REMOTE CONTROL UNIT
Random
Assemble
Editing
Menu
PLAY
R.A.EDIT
ON/OFF
SELECT SCENES
4
Point the remote control at the camcorder's
remote sensor. Press PLAY (4) and then press
R.A.EDIT ON/OFF on the remote control.
The Random Assemble Editing Menu appears.
5
If using a Fade/Wipe at the beginning of the
scene, press FADE/WIPE on the remote control.
• Cycle through the effects by pressing repeatedly,
and stop when the one you want is displayed.
• You cannot use a Picture Wipe/Dissolve at the
beginning of Programme 1.
6
At the beginning of the scene, press EDIT IN/
OUT on the remote control. The Edit-In position
appears in the Random Assemble Editing Menu.
7
At the end of the scene, press EDIT IN/OUT. The
Edit-Out position appears in the Random Assemble
Editing Menu.
8
If using a Fade/Wipe at the end of the scene,
press FADE/WIPE.
• Cycle through the effects by pressing repeatedly,
and stop when the one you want is displayed.
• If you select a Fade/Wipe effect for an Edit-Out
point, the effect is automatically applied to the
following Edit-In point.
• You cannot use a Picture Wipe/Dissolve at the end
of the last scene.
• When you use Fade/Wipe effects, that time is
included in the total time (this does not apply to
Picture Wipe/Dissolve).
9
If using Playback Special Effects, press EFFECT
(
pg. 65).
10
Repeat steps 6 through 9 to register additional
scenes.
• To change previously registered points, press
CANCEL on the remote control. The registered
points disappear, one at a time, from the most
recently registered point.
• If you are not using Fade/Wipe or Programme AE
with special effects, repeat steps 6 and 7 only.
NOTES:
When choosing a scene, set Edit-In and Edit-Out points so
that there is a relatively large difference between them.
If the search time for an in-point exceeds 5 minutes, the
recording deck's Record-Standby mode will be cancelled
and editing will not take place.
If there are blank portions before or after the Edit-In and
Edit-Out points, a blue screen may be included in the edited
version.
Since time codes register time only as accurately as
seconds, the time code total time may not match the total
programme time exactly.
Turning off the camcorder's power erases all registered Edit-
In and Edit-Out points.
If you select Sepia or Monotone mode from Programme AE
with special effects, you cannot use the Dissolve or Black &
White Fader. In this case the Dissolve or Black & White
indicator begins blinking. Once the next Edit-In point is
registered, the effect is turned off. To combine these effects,
use Sepia or Monotone during recording, then use the Dissolve
or Black & White Fader during Random Assemble Editing.
It is not possible to use Fade/Wipe effects and Programme
AE with special effects during Random Assemble Editing
using a DV cable.
(cont.)
Hide quick links:
Advertisement
Table of Contents
