Bontrager GoTime Basic Instructions

Bontrager GoTime Basic Instructions

Gotime bicycle accessories
Hide thumbs Also See for GoTime:

Advertisement

EN
GoTime
Basic Instructions

About this manual

Please read this manual carefully. If you do not understand the
information, or you have a question that this manual does not cover,
consult your Bontrager dealer or download the complete instruction
manual from www.bontrager.com/support/owners_manuals.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GoTime and is the answer not in the manual?

Questions and answers

Marilyn
March 30, 2025

How to reset odometer

1 comments:
Mr. Anderson
March 31, 2025

To reset the odometer on a Bontrager GoTime:

1. Browse to the odometer screen.
2. Press the button until the total distance appears with the first digit flashing.
3. Press the button to change the first digit.
4. Press again to move to the next digit.
5. Repeat step 3 for each digit.
6. After saving the changes, the GoTime switches to ride mode and shows the odometer screen.

This answer is automatically generated

robert young
March 15, 2025

how many inches is a trek verve 3 700x 45 tire

1 comments:
Mr. Anderson
March 15, 2025

The provided context does not contain information about a 700x45 tire specification. However, based on the listed tire sizes, it follows a pattern where the last number represents the tire width in millimeters. Since a 700x40 tire is listed with a code of 2200, a 700x45 tire would likely be slightly larger, but its exact value is not provided.

For an approximate inch size, 700mm diameter is roughly 27.5 inches, and 45mm width is about 1.77 inches, making the tire approximately 27.5 x 1.77 inches.

This answer is automatically generated

Subscribe to Our Youtube Channel

Summary of Contents for Bontrager GoTime

  • Page 1: About This Manual

    GoTime Basic Instructions About this manual Please read this manual carefully. If you do not understand the information, or you have a question that this manual does not cover, consult your Bontrager dealer or download the complete instruction manual from www.bontrager.com/support/owners_manuals.
  • Page 2: Table Of Contents

    Tools required ........... 3 To re-set the time ..........18 Parts list............3 To re-set all data and settings ......20 Installing your GoTime Custom tire size To install the speed sensor & wheel magnet ..4 To measure rollout .......... 23 To insert the battery ..........
  • Page 3: Getting Started Process Overview

    Getting started: process overview Getting your GoTime up and running is easy and takes only about 10 minutes. However, it will help you through the process if you take the time to completely read this manual before you start. For example, you cannot complete the setup process (#3 below) if the sensor cannot read the magnet in the wheel (#1).
  • Page 4: Installing Your Gotime

    Installing your GoTime To install the speed sensor and wheel magnet 3-5mm 3-5mm...
  • Page 5: To Insert The Battery

    To insert the battery To increase battery life, the GoTime is shipped with the battery NOT INSTALLED. Before proceeding with the setup, you must install the battery. After you install the battery, do not place the computer back into the band because you will need access to the SET button on the back of the computer.
  • Page 6: To Set-Up Your Preferences

    To set up your preferences After you install the battery, the Setup procedure starts automatically. Place the GoTime within 27” (70 cm) of the sensor, and be ready to activate the sensor as explained in the next section. You can begin the Setup procedure without re-installing the battery.
  • Page 8 5. To change the hours, press . To scroll faster, hold To save and proceed to the Minutes screen, press 6. To change the minutes, press . To scroll faster, hold To save and exit the programming mode, press The Ride screen appears with Speed/Clock mode. 7.
  • Page 10: To Attach The Computer

    To attach the computer You can attach the computer to the handlebar (only). Consider your preference for left and right, and your access to the button on the computer.
  • Page 12: Using Your Gotime

    Using your GoTime This section gives you the information you need to enjoy your ride: how to see the modes of the GoTime, and how to start your ride. Viewing the screens These steps start with Speed/Clock mode, which is what you see after completing the Setup Procedure.
  • Page 13 2 seconds...
  • Page 14: Changing The Setup

    . Repeat until your preferred size appears. You can also set a custom tire size; see Setting a Custom Tire Size, page 11. To save, press After you save your changes, the GoTime switches to ride mode and the trip screen appears.
  • Page 16: To Re-Set The Odometer

    3. Press to change the first value. Press to select and move to the next digit 4. Repeat step 3 for the other digits. After you save your changes, the GoTime switches to ride mode and the odometer screen appears.
  • Page 18: To Re-Set The Time

    To re-set the time 1. Browse to the clock screen. 2. Press The clock type (12 or 24) appears. 3. To the change the clock type (choose 12 or 24 hour), press To save and proceed to the hours screen, press 4.
  • Page 20: To Re-Set All Data And Settings

    To scroll faster, hold for a few moments. To save and exit the set-up procedure, press After you save your changes, the GoTime switches to ride mode and the clock screen appears. To re-set all data and settings A Re-set of the computer erases all data and settings. Before you do a re-set, you may want to write down your odometer total.
  • Page 22: Setting A Custom Tire Size

    Setting a custom tire size To setup a custom wheel size, use the Tire Size chart or measure the bike’s rollout (the distance the bike travels in exactly one revolution of the wheel). Then setup the computer. Tire size Code 12 x 1.75 24 x 2.125 196.5...
  • Page 23: To Measure Rollout

    Mark the new location of the valve stem. Measure the distance between the marks. If needed, convert to millimeters. The result is your custom wheel size. Go to the next page to program the GoTime with your wheel size.
  • Page 24: To Set-Up A Custom Tire Size

    To set-up a custom tire size 1. Remove the computer from the band. 2. Press until the trip screen appears. Press 3. To change units (choose kmh or mph), press To save and proceed to the tire size screen, press 4.
  • Page 26 . To scroll faster, hold To save and proceed to the next digit, press 7. Repeat step 6. for the other three digits of the code. After you save the last digit, the GoTime switches to ride mode and the trip screen appears.
  • Page 28 Bontrager & Bontrager B-Dot are registered trademarks of Trek Bicycle Corporation. ©2011 Trek Bicycle Corporation, Waterloo, Wisconsin 53594 USA. All rights reserved.

Table of Contents

Save PDF