3 Precision Time Protocol (PTP) / IEEE1588 4 PCI Express (PCIe) 5 Mounting and Configuration of the PTP card 6 Connectors and LEDs in the rear slot cover 7 Time codes 8 Technical Specifications PTP270PEX Date: 22nd November 2012 PTP270PEX...
Page 2 2 General information 2 General information PTP270PEX can not be used as a standard network interface card. 2.1 Content of the USB stick 2.2 Mode of operation 2.3 Features PTP270PEX Date: 22nd November 2012 PTP270PEX...
Page 6
2.4 Pulse and frequency outputs Page 3 2.4 Pulse and frequency outputs 2.5 Time capture inputs 2.6 Asynchronous serial port PTP270PEX Date: 22nd November 2012...
Page 7
Page 4 2 General information 2.7 Block Diagram PTP270PEX Date: 22nd November 2012 PTP270PEX...
Page 5 3 Precision Time Protocol (PTP) / IEEE1588 3.1 General Information PTP270PEX Date: 22nd November 2012...
Page 9
Page 6 3 Precision Time Protocol (PTP) / IEEE1588 3.2 Functionality in Master Systems 3.3 Functionality in Slave Systems Date: 22nd November 2012 PTP270PEX...
Page 10
3.4 PTPv2 IEEE 1588-2008 Conguration Guide Page 7 3.4 PTPv2 IEEE 1588-2008 Configuration Guide 3.4.1 General Options 3.4.2 Network Layer 2 or Layer 3 3.4.3 Multicast or Unicast PTP270PEX Date: 22nd November 2012...
Page 11
Page 8 3 Precision Time Protocol (PTP) / IEEE1588 3.4.4 Two-Step or One-Step 3.4.5 End-To-End (E2E) or Peer-To-Peer (P2P) Delay Measurements 3.4.6 Mode Recommendations 3.4.7 Message Rate Settings Date: 22nd November 2012 PTP270PEX...
5 Mounting and Conguration of the PTP card 5 Mounting and Configuration of the PTP card 5.1 Configuring the 9 pin connector Pin 1: Pin 4: Pin 7: D-SUB Pin Signal Signal level DIL-switch 5.2 Installing PTP270PEX in your computer Date: 22nd November 2012 PTP270PEX...
In this case, absolute care must be taken if another device is connected to the port, because voltage levels of -12V through +12V (as commonly used with RS-232 ports) at TTL inputs or outputs may damage the module. PTP270PEX Date: 22nd November 2012...
7.5 Assignment of CF Segment in IEEE1344 Code Page 17 7.5 Assignment of CF Segment in IEEE1344 Code Bit No. Designation Description PTP270PEX Date: 22nd November 2012...
Page 22
The given values for the accuracy of frequency and �me (not short term accuracy) are only valid for a constant ambient temperature ! A minimum �me of 24h of GPS-synchronicity is required before free run starts. 8.1 CE-Label EN 60950-1 EN50081-1 EN50082-2 PTP270PEX Date: 22nd November 2012...
Page 23
Konformitätserklärung Declaration of Conformity Hersteller Meinberg Funkuhren GmbH & Co. KG Lange Wand 9 Manufacturer D-31812 Bad Pyrmont erklärt in alleiniger Verantwortung, daß das Produkt declares under its sole responsibility, that the product PTP Slot Card Produktbezeichnung Product Name PTP270PEX...
Need help?
Do you have a question about the PTP270PEX and is the answer not in the manual?
Questions and answers