Table of Contents
Advertisement
Side View
(not to scale)
24 3/4"
4"
*Finished Width
Locate Grounded
Electrical outlet
Within Solid
Area Above
84 1/2" max
83-1/4" min
Finished
Opening
Supply Within
5"
3 1/2"
*36" Min. for a flush installation into an enclosure.
*35-1/2" Min. for a semi-flush installation into an enclosure.
Note: Additional cutout width may be required when side panels are
used. Add side panel thickness to the finished cutout to calculate
rough-in width. See installation examples on page 4.
Front View
(not to scale)
35" Case Width
36" Overall Width
12 1/4" max
10-3/4" min
72 1/4"
(not to Scale)
7"
5"
12 3/8"
74" From
Bottom of
Electrical Area
Locate Water
the Shaded
Area Below
5"
3 1/2"
Custom Panel Dimensions
ZISW36D (white dispenser)
ZISB36D (black dispenser)
Design Information
Cutout dimensions, clearances and side panel sizes are
determined by the many installation options available. Side
panels must be used whenever the sides of the refrigerator
will be exposed. Side panels are not required when
refrigerator is installed into an enclosure or between pantry
and oven cabinets. IMPORTANT–Side panels, 1/2" min.
thick, are required for FRAMELESS CABINETS.
• Field installed custom panels, Lexan
panels are required. Custom door panels and grille panel
sizes vary to accommodate the kit being used.
84 1/2" max
• A custom toekick can be installed to match or comple-
83" min
ment the surrounding cabinetry. Use supplied toekick as
a template to cut notches for hinges and water lines.
Optional Kits:
• ZWBP36D: Black Lexan
• ZWWP36D: White Lexan
• ZWSP36D: Stainless Steel Panel Kit (no trim kit required).
• ZKH1: For installation of custom handles on 1/4" panels.
• ZKT36: For installation of 3/4" custom panels.
• ZKHT1: For installation of custom handles on 3/4" panels.
(This kit must be used in combination with ZKT36.)
• ZWCD1: For installation of a custom collar trim on the
dispenser for one continuous custom panel
on the freezer door.
• ZKHSS1: Tubular Stainless Steel handles on 1/4" panels.
Wall View
• ZKHTSS1: Tubular Stainless Steel handles on 3/4" panels.
(This kit must be used in combination with ZKT36.)
• ZG2: 1/4" grille panel frame side pieces for 83", 83-1/2" and
84-1/2" installation heights. Factory set height is 84".
Additional Specifications
• A 115 volt 60 Hz., 15 or 20 amp power supply is required.
An individual properly grounded branch circuit or circuit
breaker is recommended. Install a properly grounded
Floor to
3-prong electrical receptacle recessed into the back wall.
Electrical must be located on rear wall.
• Water line can enter opening through the floor or back
wall. The water line should be 1/4" O.D. copper tubing
between the cold water line and water connection
location, long enough to extend to the front of the
refrigerator. Installation of an easily accessible shut off
valve in the water line is recommended.
Clearances
If the refrigerator is to be installed in a corner:
• A 4" min. clearance between the case trim and adjacent
wall on both sides of the refrigerator will assure a 90°
door opening and access to all drawers. A 10" clearance
is required on both sides for removal of pans.
36" Built-In Refrigerator
®
or stainless steel
®
Panel Kit (no trim kit required).
®
Panel Kit (no trim kit required).
10
Advertisement
Table of Contents
