Heat & Glo 8000TRC Installer's Manual

Heat & Glo 8000TRC Installer's Manual

Heat-n-glo fireplace
Table of Contents

Advertisement

Model:
8000TRC
WARNING: IF THE
INFORMATION IN THESE
INSTRUCTIONS IS NOT
FOLLOWED EXACTLY, A FIRE
OR EXPLOSION MAY RESULT
CAUSING PROPERTY DAMAGE,
PERSONAL INJURY, OR DEATH.
- Do not store or use gasoline or other flam-
mable vapors and liquids in the vicinity of
this or any other appliance.

- What to do if you smell gas

• Do not try to light any appliance.
• Do not touch any electrical switch.
• Do not use any phone in your building.
• Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call
the fire department.
- Installation and service must be performed by a
qualified installer, service agency, or the gas
supplier.
Printed in U.S.A. Copyright 1999,
Heat-N-Glo, a division of Hearth Technologies Inc.
20802 Kensington Boulevard, Lakeville, MN 55044
This product is covered by one or more of the following patents: (United States) 4,112,913; 4,408,594; 4,422,426; 4,424,792; 4,520,791; 4,793,322;
4,852,548; 4,875,464; 5,000,162; 5,016,609; 5,076,254 5,191,877; 5,218,953; 5,328,356; 5,429,495; 5,452,708; 5,542,407; 5,613,4 87; (Australia)
543790; 586383; (Canada) 1,123,296; 1,297,746; 2,195,264; (Mexico) 97-0457; (New Zealand) 200265; or other U.S. and foreign patents pending.
READ THIS MANUAL BEFORE INSTALLING OR
OPERATING THIS APPLIANCE. THIS
INSTALLERS GUIDE MUST BE LEFT WITH
THE APPLIANCE FOR FUTURE REFERENCE.
WARNING: IMPROPER INSTALLATION,
ADJUSTMENT, ALTERATION, SER-
VICE OR MAINTENANCE CAN CAUSE
INJURY OR PROPERTY DAMAGE.
REFER TO THIS MANUAL. FOR ASSIS-
TANCE OR ADDITIONAL INFORMA-
TION CONSULT A QUALIFIED IN-
STALLER, SERVICE AGENCY, OR THE
GAS SUPPLIER.
This appliance may be installed in an
1.
aftermarket, permanently located,
manufactured (mobile) home, where
not prohibited by local codes.
2. This appliance is only for use with the
type of gas indicated on the rating
plate. This appliance is not convertible
for use with other gases, unless a
certified kit is used.
Please contact your Heat-N-Glo dealer for any
questions or concerns. For the number of your nearest
Heat-N-Glo dealer, please call 612-985-6000.

Advertisement

Table of Contents
loading

Summary of Contents for Heat & Glo 8000TRC

  • Page 1 Model: 8000TRC READ THIS MANUAL BEFORE INSTALLING OR OPERATING THIS APPLIANCE. THIS WARNING: IF THE INSTALLERS GUIDE MUST BE LEFT WITH INFORMATION IN THESE THE APPLIANCE FOR FUTURE REFERENCE. INSTRUCTIONS IS NOT FOLLOWED EXACTLY, A FIRE WARNING: IMPROPER INSTALLATION, OR EXPLOSION MAY RESULT...
  • Page 2: Safety And Warning Information

    SAFETY AND WARNING INFORMATION READ and UNDERSTAND all instructions carefully before starting the installation. FAILURE TO FOLLOW these installation instructions may result in a possible fire hazard and will void the warranty. Prior to the first firing of the fireplace, READ the Using Your Fireplace section of the Owners Guide .
  • Page 3 Table of Contents...
  • Page 8 Framing should be constructed of 2 X 4 lumber or heavier. NOTE: DIMENSIONS SHOWN IN INCHES...
  • Page 9 Vent system components Vent system termination kits...
  • Page 10 6-7/16" 6-5/32" (164 mm) (156 mm) 8-1/2" (216 mm) 8-1/2" 11-5/8" 11-1/16" (216 mm) (295 mm) 7-3/8" 5-7/8" (281 mm) 6-1/2" 5-1/16" (187 mm) (149 mm) (165 mm) (129 mm) 8-5/8" (220 mm) 8-5/8" 11-15/16" (220 mm) (303 mm) 47-3/4" (1.2 m) 35-3/4"...
  • Page 12 HORIZONTAL VENTING Kit No. Max. Run DVK-01D DVK-01TRD 24" (610 mm)
  • Page 15 H + H 1´ MIN. (305 mm) 2´ MAX. (610 mm) 5´ MAX. (1.52m) 2´ MIN. (610 mm) 4´ MAX. (1.22 m) 10´ MAX. (3.1m) 3´ MIN. (914 mm) 6´ MAX. (1.86 m) 15´ MAX. (4.65m) 4´ MIN. (1.22 m) 8´...
  • Page 17 VENTING WITH TWO (2) 90 ELBOWS V FT. H + H (FT.) 1' MIN. (305mm) 2' MAX. (610mm) 2' MIN. (610mm) 4' MAX. (1.22m) 3' MIN. (914mm) 6' MAX. (1.86m) 4' MIN. (1.22m) 8' MAX. (2.4m) V+H+H 40' MAX. (12.4m) 8' MAX.
  • Page 18 VENTING WITH THREE (3) 90° ELBOWS H + H 1´ MIN. (305 mm) 2´ MAX. (610 mm) 5´ MAX. (1.52 m) 2´ MIN. (610 mm) 4´ MAX. (1.22 m) 10´ MAX. (3.1 m) 3´ MIN. (914 mm) 6´ MAX. (1.86 m) 15´...
  • Page 21 STARTING STARTING COLLAR COLLAR STOVE STOVE SEALANT SEALANT BEAD BEAD 3/8" (9.5 mm) 3/8" (9.5 mm) FIRST FIRST VENT VENT COMPONENT COMPONENT 1 INCH (25.4 mm)
  • Page 23 WALL BRACKET WALL STUD 8 FT. (2.4 m) FLUE FLUE OUTLET OUTLET 1 INCH MIN. 1 INCH MIN. (25.4 mm) (25.4 mm)
  • Page 24 12" 12" (305 mm) (305 mm) 12" 12" (305 mm) (305 mm) 1" (25.4 mm) VENT PIPE TRIM HEAT TRIM HEAT HEAT SHIELD SHIELD IF TOO SHIELD IF TOO LONG, ADD TO LONG, ADD TO SHIELD IF TOO SHIELD IF TOO SHORT.
  • Page 25 11" (280 mm) 11" (280 mm) CHIMNEY CHIMNEY HOLE HOLE EXISTING CEILING EXISTING CEILING FRAMING FRAMING JOISTS JOISTS MEMBERS MEMBERS CEILING JOIST CEILING NAILS (4 REQUIRED) CEILING FIRESTOP...
  • Page 26 NAILS (4 REQUIRED) RAFTER CEILING CEILING FIRESTOP...
  • Page 28 openable fixed closed J or K 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4...
  • Page 30 TERMINATION...
  • Page 32 DSI IGNITION NOTE: FLAMES TOO CLOSE TO THE CERAMIC INSULATORS CAN CAUSE NUISANCE LOCKOUTS AND ELECTRODE FAILURE. STANDING PILOT...
  • Page 33 USE A WRENCH ON USE A WRENCH ON SHUT-OFF VALVE WHEN SHUT-OFF VALVE WHEN TIGHTENING GAS LINE. TIGHTENING GAS LINE. MANUAL SHUT-OFF MANUAL SHUT-OFF VALVE VALVE GAS VALVE FLEX CONNECTOR...
  • Page 35: Speed Control

    FAN WIRING DIAGRAM NOTE: IF ANY OF THE ORIGINAL WIRE NOTE: IF ANY OF THE ORIGINAL WIRE VARIABLE SPEED CONTROL AS SUPPLIED WITH THE APPLIANCE AS SUPPLIED WITH THE APPLIANCE MUST BE REPLACED, IT MUST BE MUST BE REPLACED, IT MUST BE REPLACED WITH TYPE 105 DEGREE C REPLACED WITH TYPE 105 DEGREE C RATED WIRE.
  • Page 41 Type of Fireplace Fireplace Maintenance Task To Maintenance Frequency Be Completed Replacing Once annually, Qualified Brush away loose ember material near Old Ember during the Service the burner. Replace old ember Material annual check-up Technician material with new dime-size and -shape pieces of Golden Ember (GE-93) and Glowing Ember (050-721).
  • Page 42 MAKE SURE THE FLAMES ARE STEADY—NOT LIFTING OR FLOATING. DSI IGNITION STANDING PILOT 3/8" (10 mm)
  • Page 43 PART PART DESCRIPTION PART NUMBER Valve LP SRV60–523 Valve NG SRV60–522 Piezo Ignitor SRV60-513 Thermopile SRV60–512 Thermocouple SRV446-511 Pilot Orifice LP SRV446–517 Pilot Orifice NG SRV446–505 Pilot Assembly LP SRV530-511A Pilot Assembly NG SRV530-510A Pilot Tube SRV485-301A...
  • Page 44 PART PART DESCRIPTION PART NUMBER DSI Valve SRV492–500 SRV492–501 DSI Module SRV501–592 Electrode SRV459-591...
  • Page 45 PART PART DESCRIPTION PART NUMBER Burner Orifice NG (#31A DMS) SRV506-800 LP (#49A DMS) SRV65-801 On/Off Rocker Switch SRV60–521A Glass Door Assembly GLA-950 Grate Assembly SRV582-360A Burner Tube SRV477-312 Burner SRV582-378A...
  • Page 46 PART PART DESCRIPTION PART NUMBER Refractory Front SRV582-370 Refractory Right Side SRV582-377 Refractory Left Side SRV582-376 Trim Door DF-950M Log Set Assembly Logs-8TRC...
  • Page 47 PART PART DESCRIPTION PART NUMBER Log #1 SRV582-701 Log #2 SRV582-702 Log #3 SRV582-703 Log #4 SRV582-704 Log #5 SRV582-705 Log #6 SRV582-706 Log #7 SRV582-707 Log #8 SRV402-701...
  • Page 48 ACCESSORY PART DESCRIPTION PART NUMBER Fan Kit GFK-160A GFK-230 Remote Control Kit RC-SMART SMART-STAT RC-MLT Wall Switch Kit WSK-21 Off White WSK-21-W White Trim Door Mesh MESH-8TRC Conversion Kit NG Conversion NGK-8TRC LP Conversion LPK-8TRC...

Table of Contents