Replacing The Spool; Replacing The Cutting Line - Ryobi RLT3025F Operator's Manual

Make sure that the area to be cut is free of stones,
n
debris, wires and any other objects.
Secure the power cord using the cord retainer.
n
Loop the cord through the cord retainer slot then
around the tongue. The cord retainer helps prevent
accidental unplugging of the cord.
In order to make the arm support handle work
n
ergonomically, make sure that your arm is aligned
with the back of the arm support handle and use your
index finger to press the trigger button.
When starting the line trimmer for the first time,
n
ensure that the nylon lines touch or pass over the cut-
off blade. If they are not long enough, press the bump
button and pull the line at the same time.
Connect the plug of the line trimmer or the connected
n
extension cable to the electric supply.
WARNING
These steps should be repeated every time
before starting work to make sure that everything
is functioning properly and to familiarise yourself
with the line trimmer.
Do not start the trimmer when it is upside down or not
n
in working position.
Switch the trimmer on before the line makes contact
n
with the grass. Ensure the line is not touching stones
or debris.
Turn the line trimmer on by pressing in the lock-off
n
button then squeezing the trigger with your index
finger. Once the trimmer is running, there is no need
to keep the lock-off button pressed.
Start off slowly. When you have gained experience,
n
you will be able to use the line trimmer to its full
potential.
High grass should be cut in layers, always begin from
n
the top. The cuts should be short.
Do not cut damp or wet grass. Dry grass will give
n
excellent results.
Always let the line rotate at top speed. Do not
n
overload the trimmer.
Avoid knocking the line against hard objects (stones,
n
walls, fences etc.). It will wear the line out quickly.
Never pass the line trimmer over the electric cable
n
while it is running; make sure the cable is always in a
safe position behind your back.
To switch off the line trimmer, simply release the
n
trigger.
CAUTION
After switching off, the nylon line will continue to
rotate for a few more seconds.
ENGLISH (Original Instructions)
LINE TRIMMING CUT-OFF BLADE
This trimmer is equipped with a line trimming cut-off
blade on the safety guard. For best cutting, advance
fresh lines by gently tapping the bump head on the
ground (Figure 8). Fresh lines will be released from the
bump head and trimmed to optimum length by the cut-
off blade. Advance line whenever you hear the engine
running faster than normal and when it is apparent that
the line is worn or broken. This will maintain best cutting
performance.
MAINTENANCE
WARNING
Switch off and disconnect from the mains supply
before replacing, adjusting or cleaning your
trimmer. Be aware that the trimmer continues to
rotate for a few more seconds after it has been
switched off.

REPLACING THE SPOOL

See Figure 9.
Press the spool cover lock buttons on both sides of
n
the spool and remove the spool cover.
Replace the spool with the new parts.
n
Place the spool, spring and spool cover into position
n
and push in until the spool cover lock buttons clicked
into the designated cut outs and the spool is secured
in place.

REPLACING THE CUTTING LINE

See Figure 10.
Press the spool cover lock buttons on both sides of
n
the spool and open the spool.
Remove the spool and exchange the line.
n
Place the spool, spring and spool cover into position
n
and push in until the spool cover lock buttons clicked
into the designated cut outs and the spool is secured
in place.
CLEANING THE LINE TRIMMER
WARNING
Do not touch the cut-off blade on the grass shield
to avoid injury
Regular cleaning and maintenance of your line
n
trimmer will ensure efficiency and prolong the life of
the unit.
After each cutting operation, remove the grass and
n
soil from the spool, the whole trimmer and the grass
shield.
During operation, keep the air slots clean and free of
n
grass.
Only use a cloth soaked with hot water and a soft
n
6