Related Manuals for GDI XC-NT200
Summary of Contents for GDI XC-NT200
-
Page 1: Adsl Modem
XC-NT200 ADSL Modem Owners Manual GDI COMMUNICATIONS LLC. PO Box 1330 Verdi, NV 89439... - Page 2 In no event shall GDI Communications LLC. be liable for any loss of profits, loss of equipment or facilities, or the loss of programs or data, or the cost of recovering or reproducing the program or data.
-
Page 3: Table Of Contents
TABLE OF CONTENTS GENERAL INFORMATION ..............4 FEATURES ..................4 INSTALLATION ..................5 CONNECTING TO THE ADSL LINE INTERFACE ......6 CONNECTING THE LAN (ETHERNET) INTERFACE ....7 CONNECTING POWER .............. 8 OPERATION ..................9 POWER UP ..................9 FRONT PANEL LED STATUS MONITORS ......9 CUSTOMER SERVICE .............. -
Page 4: General Information
-37°C to +74°C, in non-condensing humidity of up to 95%. It can be set up at altitudes of up to 10,000 feet. This manual has been designed to enable you to install your XC-NT200 modem by following the step-by-step installation procedure. Follow the step-by-step installation instructions outlined in Section titled - Installation. -
Page 5: Installation
INSTALLATION Because the XC-NT200 requires no configuration, it can be installed and made operational quickly. Installation takes place as follows: 1. Connecting the ADSL line (refer to section titled, “Connecting the ADSL Line Interface” on page 6) See Figure 4 for the rear panel connector arrangements. -
Page 6: Connecting To The Adsl Line Interface
Actual distance and link performance may vary depending on the environment and type or gauge of wire used. Follow the steps below to connect the XC-NT200 ADSL Interface to the DSL ready telephone line. Connect a telephone phone cable from the DSL-equipped telephone line jack to the jack marked ADSL on the rear panel of the modem. -
Page 7: Connecting The Lan (Ethernet) Interface
XC-NT200 LAN (10/100BaseT/TX) RJ-45 Connector Pin out. Connecting the LAN (10/100BaseT/TX) Ethernet Port to a Hub The XC-NT200 LAN interface is configured as DCE (Data Communications Equipment), just like a 10/100BaseT/TX network hub or a switch. Therefore, it "expects" to connect to a DTE (Data Terminal Equipment) device such as a PC or a router. -
Page 8: Connecting Power
CONNECTING POWER An external AC cube style power supply is available. Power to the XC-NT200 is connected using the barrel jack on the rear panel. No configuration is necessary for the power supply. AC power supplied must meet the following requirements;... -
Page 9: Operation
OPERATION Once the XC-NT200 is properly installed, the set should operate transparently. No user settings are required. This section describes the LED status monitors. POWER UP Before applying power to the XC-NT200, please review section titled, “Connecting Power” to verify that the unit is connected to the appropriate power source. - Page 10 LED Description Indication Steady GREEN to indicate the unit is powered ON. No Light No Power power Steady green (ON) to indicate that the ADSL link is established. Slow Flashing Green Power ON and passed power-up diagnostics (1 flash/sec) Moderate Flashing Green Power ON and attempting synchronization (2 flashes/sec) ADSL Sync Steady Red (less than 20 sec.) Hardware power-up in...
-
Page 11: Customer Service
There shall be no warranty for either parts or labor after the expiration of one year from the date of purchase or if in GDI Communications sole discretion the product has been deemed to be modified or abused. -
Page 12: Appendix A
APPENDIX A SPECIFICATIONS CONNECTORS LAN: Shielded or Unshielded RJ-45, 10/100Base-T, IEEE 802.3 Ethernet ADSL: RJ 11 ADSL ENVIRONMENT LINE: 19 to 26 AWG (0.5 mm) twisted-pair wire LED INDICATORS PWR, Power (Green) RDY, ADSL Sync (Green) ADSL, Ethernet Good Link (Green/Red/Amber) ACT, Ethernet Activity (Green) POWER SUPPLY External AC power cube input 112 VAC, 47 to 63Hz, >6 Watt... - Page 13 APPROVALS FCC NOTICE The XC-NT200 generates and uses radio frequency energy, and if not properly installed and used in strict accordance with the manufacturer’s instructions it may cause interference to radio and television reception. The XC-NT200 has been tested and found to comply with Class B computing device in accordance with specifications in Subpart B of Part 15 of FCC rules.
-
Page 14: Appendix B
APPENDIX B FACTORY REPLACEMENT PARTS AND ACCESSORIES GDI Communications Model Description Model Description Hardened ADSL Modem, no power supply XC-NT200 112VAC input NTAPS... -
Page 15: Appendix C
APPENDIX C INTERFACE PIN ASSIGNMENT LAN (ETHERNET 10/100BASET/TX) INTERFACE: RJ-45 UTP/STP Pin 1: RX+ Pin 2: RX- Pin 3: TX+ Pin 6: TX- Pins 4, 5, 7, 8: no connection Shield: Bat Com (STP only) ADSL LINE INTERFACE: RJ-11 Pin 2: RING Pin 3: TIP Pins 1, 4: no connection... - Page 16 Copyright © 2003 GDI Communications LLC. All Rights Reserved.