Related Manuals for GDI NT 200R-Plus
Summary of Contents for GDI NT 200R-Plus
- Page 1 NT 200R-PLUS ADSL Modem/Router User Guide GDI COMMUNICATIONS LLC., PO Box 1330, Verdi NV 89439...
- Page 2 GDI Communications LLC.'s liability shall not exceed the price of the defective individual product, which is the basis for claim. In no event will GDI Communications LLC. be liable for direct, indirect, incidental, or consequential damages resulting from any defect in the product or in this manual, even if they have been advised of the possibility of such damages.
-
Page 3: Table Of Contents
TABLE OF CONTENTS GENERAL INFORMATION ............4 FEATURES .................4 INSTALLATION..............5 CONNECTING TO THE ADSL LINE INTERFACE .....6 CONNECTING THE LAN (ETHERNET) INTERFACE..7 CONNECTING POWER............8 OPERATION................9 POWER UP.................9 FRONT PANEL LED STATUS MONITORS .......9 CONFIGURING FOR INTERNET CONNECTION ....11 SETTING UP YOUR PC............11 WAN CONFIGURATION: ..........13 LAN CONFIGURATION:...........14 VPN CONFIGURATION:...........15... -
Page 4: General Information
GENERAL INFORMATION Thank you for purchasing this GDI Communications LLC. product. The NT200R-PLUS provides reliable, high-speed, Internet access to your existing phone line. There is no special wiring or special networking knowledge required. This modem is capable of data rates hundreds of times faster than a traditional analog modem. -
Page 5: Installation
INSTALLATION Because the NT200R-PLUS requires minimum configuration, it can be installed and made operational quickly. Installation takes place as follows: 1. Connecting the ADSL line (refer to section titled, “Connecting the ADSL Line Interface” on page 6) See Figure 4 for the rear panel connector arrangements. 2. -
Page 6: Connecting To The Adsl Line Interface
CONNECTING TO THE ADSL LINE INTERFACE The NT200R-PLUS supports High-speed communications over 24 AWG (0.5 mm) twisted-pair wire. Actual distance and link performance may vary depending on the environment and type or gauge of wire used. Follow the steps below to connect the NT200R-PLUS ADSL Interface to the DSL ready telephone line. -
Page 7: Connecting The Lan (Ethernet) Interface
CONNECTING THE LAN (ETHERNET) INTERFACE The RJ-45 ports are labeled “LAN”, 1 through 4. These ports are designed to connect directly to a 10/100BaseT/TX network. Figure 3 shows the signal/pin relationships on this interface. You may connect these ports to another Ethernet device via a Cat 3 or Cat 5 cable that is up to 328 ft long. -
Page 8: Connecting Power
CONNECTING POWER An external AC cube style power supply is available. Power to the NT200R-PLUS is connected using the barrel jack on the rear panel. No configuration is necessary for the power supply. AC power supplied must meet the following requirements; 12DC, 1A. -
Page 9: Operation
OPERATION Once the NT200R-PLUS is properly installed, the set should operate transparently. This section describes the LED status monitors. POWER UP Before applying power to the NT200R-PLUS, please review section titled, “Connecting Power” to verify that the unit is connected to the appropriate power source. - Page 10 LED Description NT200R-PLUS Indication Steady GREEN to indicate the unit is powered ON. Power No Light No Power. RED resetting or problem state. Slow Flashing Green Power ON and Waiting for carrier detect signal (1 flash/sec) Moderate Flashing Green Power ON and attempting synchronization (2 flashes/sec) Steady green (ON) to indicate that the ADSL link is established.
-
Page 11: Configuring For Internet Connection
CONFIGURING FOR INTERNET CONNECTION To browse the Internet using your NT200R-PLUS, you must set up your router access, confirm your DSL sync, and establish a PPP session with your Internet service provider (ISP). SETTING UP YOUR PC Configure your computer to use an IP address on the same TCP/IP network as your router. - Page 12 Click on Refresh Config button. The router information will appear in all the fields in all tabs.
-
Page 13: Wan Configuration
WAN CONFIGURATION: This information is for the network on the ISP or DSL side of the router. • Select the WAN Tab; • Select the circuit type for your installation. Multimode T1.413 G.DMT G.Lite ADSL2 ADSL2+ ReADSL2 • Select the Data Link Encapsulation for your installation RFC1483 •... -
Page 14: Lan Configuration
LAN CONFIGURATION: This is the information for the network on the user side of the router. • Select the LAN Tab; NOTE: All addresses and subnet masks are entered in Dotted Decimal format xxx.xxx.xxx.xxx • Enter the router LAN IP address. •... -
Page 15: Vpn Configuration
VPN CONFIGURATION: If you are setting up a Virtual Private Network (VPN) you will need to use this tab. • Select VPN Tab; • Enable VPN operation by selecting YES in the VPN Enable box. • Enter a name for your VPN. •... -
Page 16: Saving Your Configuration
SAVING YOUR CONFIGURATION: All configuration changes are staged in the router and will only be applied by restarting the router. After clicking on the Save Changes button the dialog boxes below will be displayed. If you are sure of the changes you have made click on Yes. Click OK The warning screen message below will appear. -
Page 17: Customer Service
Extreme Copper) and a charge will be made for parts and labor. Products repaired/replaced under warranty will be returned to any destination within the USA at GDI Communications’s expense. The carrier and method of shipment will be determined by GDI Communications LLC. -
Page 18: Specifications
APPENDIX A SPECIFICATIONS CONNECTORS LAN: Shielded or Unshielded RJ-45, 10/100Base-T, IEEE 802.3 Ethernet ADSL: RJ 11 Power Jack ADSL ENVIRONMENT LINE: 19 to 26 AWG (0.5 mm) twisted-pair wire LED INDICATORS Power (Green) DSL Sync (Green) LAN, Ethernet Good Link (Green/Red/Amber) POWER SUPPLY External AC power cube input 112 VAC, 47 to 63Hz, >6 Watt +12.0 Output... - Page 19 APPROVALS FCC NOTICE The NT 200 generates and uses radio frequency energy, and if not properly installed and used in strict accordance with the manufacturer’s instructions it may cause interference to radio and television reception. The NT 200 has been tested and found to comply with Class B computing device in accordance with specifications in Subpart B of Part 15 of FCC rules.
-
Page 20: Interface Pin Assignment
APPENDIX B INTERFACE PIN ASSIGNMENT LAN (ETHERNET 10/100BASET/TX) INTERFACE: RJ-45 UTP/STP Pin 1: RX+ Pin 2: RX- Pin 3: TX+ Pin 6: TX- Pins 4, 5, 7, 8: no connection Shield: Bat Com (STP only) ADSL LINE INTERFACE: RJ-11 Pin 2: RING Pin 3: TIP Pins 1, 4: no connection... - Page 21 Copyright © 2011 GDI Communications LLC. All Rights Reserved.