Table of Contents
Advertisement
OPERATOR'S MANUAL
GASOLINE PRESSURE WASHER
HU80722
Your pressure washer has been engineered and manufactured to Husky's high standard for dependability, ease of operation,
and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING:
To reduce the risk of injury, the user must read and understand the operator's manual before using
this product.
Thank you for your purchase.
SAVE THIS MANUAL FOR FUTURE REFERENCE
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Husky HU80722
Summary of Contents for Husky HU80722
- Page 1 OPERATOR’S MANUAL GASOLINE PRESSURE WASHER HU80722 Your pressure washer has been engineered and manufactured to Husky’s high standard for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Introduction .................................. Important Safety Instructions ............................3 Specific Safety Rules ............................... 4 Symbols ..................................5-6 Features ..................................7-8 Assembly ..................................8-1 Operation .................................. 1-16 Maintenance ................................17-18 Troubleshooting ................................19 ... -
Page 3: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS Check damaged parts. Before further use of the tool, a guard or other part that is damaged should be carefully WARNING: checked to determine that it will operate properly and Read and understand all instructions. Failure to follow perform its intended function. -
Page 4: Specific Safety Rules
SPECIFIC SAFETY RULES Never direct a water stream toward people or pets, Never store the machine with fuel in the fuel tank or any electrical device. inside a building where ignition sources are present, such as hot water and space heaters, clothes dryers, Before starting any cleaning operation, close doors and the like. -
Page 5: Symbols
SYMBOLS Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpreta- tion of these symbols will allow you to operate the tool better and safer. SYMBOL NAME DESIGNATION/EXPLANATION Wet Conditions Alert Do not expose to rain or use in damp locations. - Page 6 If you do not under- ing, use only identical replacement parts. stand the warnings and instructions in the operator’s manual, do not use this product. Call Husky customer service for assistance. WARNING: The operation of any power tool can result in foreign objects being thrown into your eyes, which can result in severe eye damage.
-
Page 7: Features
FEATURES PRODUCT SPECIFICATIONS Engine................................Honda.GCV160 Fuel.Tank.Capacity............................48.gal.(1.8.liters) Maximum.Pounds.Per.Square.Inch.Pressure*......................2,600.psi Maximum.Gallons.Per.Minute*............................2.3.gpm Maximum.Inlet.Water.Temperature..........................104˚F *Max. rating determined by PWMA Standard 101 NozzLE CLEANING fuEL CAP TooL RECoIL sTARTER NozzLE HoLDER wITH sPRING CLIP fuEL TANK HANDLE HIGH PREssuRE HosE TRIGGER HANDLE NozzLEs AND NozzLE... -
Page 8: Know Your Pressure Washer
FEATURES KNOW YOUR pRESSURE WAShER REcOil STARTER See Figure 1. The recoil starter is pulled to start the machine. The safe use of this product requires an understanding of SOAp BlASTER™ the information on the tool and in this operator’s manual as The soap blaster™... -
Page 9: Assembly
ASSEMBLY WARNING: If any parts are damaged or missing do not operate this tool until the parts are replaced. Failure to heed this warn- ing could result in serious personal injury. WARNING: Do not attempt to modify this tool or create accesso- ries not recommended for use with this tool. -
Page 10: Adding Gasoline To The Fuel Tank
ASSEMBlY ADDiNg lUBRicANT TO ThE ENgiNE See Figure 4. NOTE: This machine has been shipped with approximately OIL CAP / 2 oz. of lubricant in the engine from testing. You must add DIPSTICK lubricant to the engine before starting it the first time. cAUTiON: Any attempt to start the engine without adding lubricant will result in engine failure. - Page 11 ASSEMBLY ATTACHING INJECTION HOSE INjECTIoN See Figure 6. HosE Before detergent can be used with this machine, the injection fITTING hose must be attached. Open the cap from the detergent container. From the top of the cap, slide the injection hose through the hole in the cap.
-
Page 12: Operation
ASSEMBLY CONNECTING THE HIGH PRESSURE HOSE TO THE PUMP See Figure 9. After the high pressure hose has been uncoiled and attached to the spray wand: Align the collar on the threaded nipple on the pump. Insert the nozzle on the end of the high pressure hose collar into the threaded nipple. - Page 13 OPERATION APPLICATIONS You may use this tool for the purposes listed below: Removing dirt and mold from decks, cement patios, and RECoIL house siding sTARTER Cleaning cars, boats, motorcycles, outdoor furniture, and grills STARTING AND STOPPING THE PRESSURE WASHER See Figures 11 - 12.
- Page 14 OPERATION USING THE SPRAY WAND TRIGGER See Figure 13. sLoT For greater control and safety, keep both hands on the trigger handle at all times. Pull back and hold the trigger to operate the pressure washer. Release the trigger to stop the flow of water through the nozzle.
- Page 15 OPERATION WASHING WITH DETERGENT See Figures 16 - 17. Use only detergents designed for pressure washers; house- DETERGENT hold detergents, acids, alkalines, bleaches, solvents, flam- CoNTAINER mable material, or industrial grade solutions can damage INjECTIoN the pump. Many detergents may require mixing prior to use. HosE Prepare cleaning solution as instructed on the solution bottle.
- Page 16 OPERATION RINSING WITH THE PRESSURE WASHER To movE THE mACHINE Turn off the pressure washer and shut off the water supply. Pull trigger to release water pressure. Engage the lock out on the trigger handle by pushing up on the lock out until it clicks into the slot.
-
Page 17: Maintenance
MAINTENANCE NOZZLE MAINTENANCE WARNING: See Figure 19. Excessive pump pressure (a pulsing sensation felt while When servicing, use only identical replacement parts. squeezing the trigger) may be the result of a clogged or Use of any other parts may create a hazard or cause dirty nozzle. - Page 18 MAINTENANCE STORING THE PRESSURE WASHER PREPARING FOR USE AFTER STORAGE See Figure 20. Pull the recoil starter grip three or four times to clean Store the pressure washer with the gas tank empty by either lubricant from the combustion chamber. draining the tank or running the pressure washer until the Remove spark plug from the cylinder.
-
Page 19: Troubleshooting
TROUBLESHOOTING PROBLEM CAUSE SOLUTION Engine fails to start 1. No fuel in tank 1. Fill tank . Spark plug shorted or fouled . Replace spark plug 3. Spark plug is broken (cracked 3. Replace spark plug porcelain or electrodes broken) 4. - Page 20 NOTES NOTES...
-
Page 21: Warranty
Techtronic Industries North America, Inc.’s responsibility in respect to claims is limited to making the required repairs or replacements and no claim of breach of warranty shall be cause for cancellation or rescission of the contract of sale of any HUSKY brand ®... - Page 22 OpERATOR’S MANUAl gASOliNE pRESSURE WAShER hU80722 WARNiNg: The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. cAliFORNiA pROpOSiTiON 65 • SERVICE Now that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest Authorized Service Center.
Need help?
Do you have a question about the HU80722 and is the answer not in the manual?
Questions and answers
Where can I get a new filter?
How to use soap dispenser
runs for 10-15 seconds with choke on are off and will not stay running. it will start back up and do the same thing again. Thanks in advance
Hooked water hose up to pressure washer husky 3000psi gas and water is shooting out underneath machine. I guess this opening is a water outlet. Should it have a cap on it to keep water from coming out?
how do you change the spray tips on the wand