Subscribe to Our Youtube Channel
Related Manuals for Digi CR4110
Summary of Contents for Digi CR4110
- Page 1 4000 Series Router Wireless (CDMA) EV-DO 450 Rev.A Installation Guide...
- Page 2 Digi International reserves the right to modify or revise all or part of this document, its contents, and any products described herein at any time without prior notification and shall not be responsible for any loss, cost or damage, including consequential damage, caused by reliance on these materials.
- Page 3 Any attempt to service or repair the unit by the user will void the product warranty. The CR4110 is designed for indoor use only and should be used in an environment that is suitable for computers and other electronic equipment.
- Page 4 However, wireless products contain radio devices which require specific consideration. Please take the time to read and understand the following guidance. Digi International assumes no liability for an end user‟s failure to comply with these precautions.
- Page 5 CR4110 Installation Guide Preface This guide describes the installation procedure for the CR4110. It is intended to provide sufficient information for you to be able to connect the unit to your terminal equipment and power supply. A complete reference guide to the software features that are available on the product is available separately in PDF format which can be downloaded from the Digi International website (www.digi.com).
-
Page 6: Front Panel Features
CR4110 Installation Guide 1 Introduction The CR4110 is a compact IP router that facilitates the transmission of data over 3G wireless CDMA EV-DO 450 networks at downlink speeds of up to 3.1Mbps and up-link speeds of up to 1.8Mbps depending on network conditions. - Page 7 CR4110 Installation Guide CDMA Off when the unit cannot detect a CDMA EV-DO 450 network, flashes when trying to detect a network and illuminates steady when a connection has been established. Illuminates steady when a wireless network has been detected.
- Page 8 STP cable. EXP. The socket labelled EXP. may be used to connect various accessories supplied by Digi International. For further information please contact your supplier. Reset switch This is located on the underside of the unit near the front. Pressing the switch gently with...
-
Page 9: Installation
CR4110 Installation Guide 2 Installation The CR4110 is designed for indoor use (office or home). The router should be positioned on a smooth, level surface making sure that there is adequate ventilation. Do not expose the router to extremes of heat or cold, strong magnetic fields or liquids. - Page 10 CR4110 Installation Guide In both cases, the end of the R-UIM card with the chamfered corner should be inserted first. For R-UIM 1 the contacts should be face down. For R-UIM 2 the contacts should be face up. Step 2 – Fitting the CDMA antennas The router is supplied with two “stub”...
- Page 11 CR4110 Installation Guide 3 Configuration Once the router has been installed and powered up, you must now configure it to communicate with your network and the Internet. Note: The default IP address for the LAN 0 port is 192.168.0.99, with a Class C subnet (255.255.255.0).
-
Page 12: General Specifications
CR4110 Installation Guide 4 General Specifications Model numbers 81-CR4110-SSEU-01 Power supply 12V DC / 1.5A Dimensions W160 x D120 x H32 mm Weight 0.53Kg Operating temp. range -20 to +50 degree Celsius Wireless Interface CDMA 1xEV-DOrA (IS-856-A) (A Block) USB ports Two USB 2.0 Full-speed Host (OHCI) (12 Mbits per second... -
Page 13: Declaration Of Conformity
EN301526: V1.1.1 (2006-7) (RF spectrum efficiency) following the provisions of Council Directive 1999/5/EC on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity. Name: D Ellison Position: Director Signature: Date: September 2009 on behalf of Digi International.
Need help?
Do you have a question about the CR4110 and is the answer not in the manual?
Questions and answers