ADEMCO VISTA-50P Installation And Programming Manual
  1. Manuals
  2. Brands
  3. ADEMCO Manuals
  4. Security System
  5. VISTA-50P
  6. Installation and programming manual

ADEMCO VISTA-50P Installation And Programming Manual

Partitioned security system with scheduling
Hide thumbs Also See for VISTA-50P:
Table of Contents

Advertisement

Quick Links

See also: User Manual
VISTA-50P
VISTA-50PUL
PARTITIONED SECURITY SYSTEM
with SCHEDULING
INSTALLATION INSTRUCTIONS
and
PROGRAMMING GUIDE
N5944-6V1 Rev B 4/99

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VISTA-50P and is the answer not in the manual?

Questions and answers

Rev. David Kossey
June 1, 2025

My Vista-50P keyboard will not take my 'Bypass' command. (The keyboard's green 'ready' indicator light is off, and I can't get it to turn on.) How do I bypass the '#**** door ajar' notice and then arm the building? ('Door '#****' is not ajar.)

0
1 comments:
Mr. Anderson
June 1, 2025

To bypass the 'door ajar' notice and arm the ADEMCO VISTA-50P system when the green 'ready' light is off, follow these steps:

1. Enter your security code.
2. Press 6 (bypass).
3. Press # to use the Quick Bypass feature.

The system will display all open (faulted) zones with the word BYPASS. Wait for the zones to be displayed, then arm the system as usual.

This answer is automatically generated

0

Related Manuals for ADEMCO VISTA-50P

Summary of Contents for ADEMCO VISTA-50P

  • Page 1 VISTA-50P VISTA-50PUL PARTITIONED SECURITY SYSTEM with SCHEDULING INSTALLATION INSTRUCTIONS PROGRAMMING GUIDE N5944-6V1 Rev B 4/99...

  • Page 3: Table Of Contents

    TABLE OF CONTENTS HOW TO USE THIS MANUAL ............vii CONVENTIONS USED IN THIS MANUAL ......... viii RECOMMENDATIONS FOR PROPER PROTECTION....ix Section 1: GENERAL DESCRIPTION ............... 01 Section 2: PLANNING A PARTITIONED SYSTEM ........05 Theory of Partitioning ................05 Setting Up a Partitioned System............
  • Page 4 Section 6: BASIC HARDWIRED ZONES 1-9 ............ 25 Common Characteristics of Hardwired Zones ........25 Wiring Burglary and Panic Devices to ones 1-8 ........25 Wiring 2-Wire Smoke Detectors to Zone 1..........26 Compatible 2-Wire Smoke Detectors ............ 27 Unsupervised Usage of Zone 1 .............. 27 Wiring 4-Wire Smoke Detectors to Zones 1-8 ........
  • Page 5 Section 10: 4285 VISTA INTERACTIVE PHONE (VIP) MODULE ....65 General Information ................65 Mounting the 4285 VIP Module ............65 Wiring the 4285 VIP Module ..............66 Programming 4285 VIP Module Options ..........67 Custom Word Substitutes for VIP Module Annunciation ....68 Section 11: AUDIO ALARM VERIFICATION (AAV) UNIT ......
  • Page 6 Section 17: ZONE TYPE DEFINITIONS ............. 92 Section 18: DATA FIELD DESCRIPTIONS ............94 Section 19: #93 MENU MODE PROGRAMMING ..........108 #93 Main Menu Options ..............108 Zone Programming ................110 Learning Serial Numbers ..............111 Programming Alpha Descriptors............113 Alpha Descriptor Vocabulary And Character (ASCII) Chart ....
  • Page 7 Section 24: SECURITY ACCESS CODES ............155 General Information ................155 User Codes and Levels of Authority ............ 155 To ADD, a Master, Manager or Operator Code ........158 To CHANGE a Master, Manager, or Operator Code ......159 Adding an RF Key to an Existing User ..........160 To DELETE a Master, Manager, or Operator Code......
  • Page 8 LIST OF FIGURES Installing The Lock ................10 Cabinet Attack Resistance Considerations ........11 Mounting The PC Board ..............12 Standard Phone Line Connections ..........13 AC Power And Battery Connections ..........14 4300 Transformer Connections ............14 Keypad Connections to Keypad Port Terminals ......21 Using a Supplementary Power Supply for Additional Keypads ..

  • Page 9: How To Use This Manual

    Each of the sections covering the installation of peripheral devices includes the programming for that device. If you are an experienced user of Ademco products, you may choose to wire and then program the entire system at once. If so, refer to Sections 18 through 20 (for complete system programming options) after the hardware setup is complete.

  • Page 10: Conventions Used In This Manual

    These prompts are shown in a double-line box. * 00 When programming the system, data fields are indicated by a “star” ( ) followed by the data field number. PRODUCT MODEL NUMBERS: Unless noted otherwise, references to specific model numbers represent Ademco products. –viii–...

  • Page 11: Recommendations For Proper Protection

    RECOMMENDATIONS FOR PROPER PROTECTION The Following Recommendations For The Location Of Fire And Burglary Detection Devices Help Provide Proper Coverage For The Protected Premises. Recommendations For Smoke And Heat Detectors With regard to the number and placement of smoke/heat detectors, we subscribe to the recommendations contained in the National Fire Protection Association's (NFPA) Standard #72 noted below.
  • Page 12 –x–...

  • Page 13: Section 1: General Description

    Section 1: GENERAL DESCRIPTION The VISTA-50P is an 8-Partition alarm control panel that supports up to 86 zones using basic hardwired, polling loop, and wireless zones. In addition, the control offers relay control and scheduling capabilities for automating system functions. The major system features are outlined below.
  • Page 14 8 Partitions Provides the ability to control 8 separate areas independently, each functioning as if it had its own separate control. Partitioning features include: • A "Common Lobby" partition, which arms automatically when the last partition (1-8) that shares the common lobby is armed and disarms when the first partition (1-8) that shares the common lobby is disarmed •...
  • Page 15 (e.g. lobby door). Each partition can be assigned one access control relay. Optional Keyswitch Supports the Ademco 4146 keyswitch on any one of the systems's 8 partitions. If used, zone 7 is no longer available as a protection zone. Voltage Triggers Provides a trigger connector whose pins change state for different conditions.
  • Page 16 Communications Formats Supports the following formats for the Primary and Secondary Central Station receivers: • Ademco Low Speed (Standard or Expanded) • Sescoa/Radionics • Ademco Express • Ademco High Speed •...

  • Page 17: Section 2: Planning A Partitioned System

    Section 2: PLANNING A PARTITIONED SYSTEM This section provides the following information: • Theory of partitioning • Setting up a partitioned system • Common Lobby Logic • Master keypad setup and operation Theory of Partitioning This system provides the ability to arm and disarm up to 8 different areas, each as if it had its own control.

  • Page 18: Common Lobby Logic

    Common Lobby Logic When an installation consists of a partition shared by users of other partitions in a building, that shared partition may be assigned as the "common lobby" partition for the system (program field 1*17). An example of this might be in a medical building where there are two doctor's offices and a common entrance area (see example that follows explanation).
  • Page 19 Example Here is an example of how the lobby would react in a typical setup. OFFICE #1 OFFICE #2 COMMON LOBBY MAIN ENTRANCE User #1 has access to Office #1 and the Common Lobby. User #2 has access to Office #2 and the Common Lobby. Office #1 is set up to affect the Common Lobby, but not arm it.

  • Page 20: Master Keypad Setup And Operation

    How User Access Codes Affect the Common Lobby Codes with "Global" Arming If a code is given "global arming" when it is defined (see Section 24: SECURITY ACCESS CODES ), the keypad will ask "Arm all?" or "Disarm all?" whenever the user tries to arm or disarm the partitions he has access to from an alpha keypad.
  • Page 21 The following is an example of a typical display: S Y S T E M 1 2 3 4 5 6 7 8 S T A T U S R R N N A * B Possible status indications include: A = Armed Away Armed Maximum S = Armed Stay...

  • Page 22: Section 3: Installing The Control

    DO NOT ATTEMPT TO REMOVE KNOCKOUTS AFTER THE CIRCUIT BOARD HAS BEEN INSTALLED. Installing The Cabinet Lock Use an Ademco No. N6277 Cam Lock and No. N6277-1 Push-On Retainer Clip (supplied). 1. Remove the lock knockout on the control cabinet cover. Insert the key RETAINER CLIP into the lock.

  • Page 23: Vista-50Pul Grade A Mercantile Premises Listing

    Night (type 05) or 24-hour audible alarm (type 07) response. The 24-hour alarm response must be used for multiple partitioned systems. • Use a bell with a tamper protected housing such as the Ademco AB12. bell housing's tamper switch and inner linings tamper must be wired to the...

  • Page 24: Installing The Circuit Board

    Installing the Control's Circuit Board Refer to the diagram below when mounting the PC board. • Hang the three mounting clips on the raised cabinet tabs. Make sure the clip orientation is exactly as shown in the diagram to avoid damage to the clip when mounting screws are tightened.

  • Page 25: Connecting The Ac Transformer

    2. If you want to connect the panel to phone lines that require ground start capability, then a 675 Ground Start Module must be used. This module is triggered by one of the outputs on the connector labeled J7 (see VOLTAGE TRIGGERS section).

  • Page 26: Ac Power And Battery Connections

    60 Hz Outlet against blowing the 3 years fuse inside the transformer (non- replaceable). TRANSFORMER 16.5VAC, 40VA ADEMCO No.1361 (IN CANADA USE No. 1361CN) or 4300 IF X-10 DEVICES WILL BE USED NOTE: WHEN POWERING UP THE PANEL, PLUG THE TRANSFORMER IN BEFORE CONNECTING THE BATTERY.

  • Page 27: Installing The Backup Battery

    The complete wiring for the 4300 transformer is also covered in Section 9: RELAY OUTPUTS & POWERLINE CARRIER DEVICES . Installing The Back-Up Battery If necessary, refer to Section 15: FINAL POWER-UP PROCEDURE for information regarding battery size to use, etc. Do not attach the connector cable to the battery terminals until you are instructed to do so later in the manual.

  • Page 28: Section 4: The Mechanics Of Programming

    • There are four sets of pre-programmed communication defaults available, including Low Speed, 4+2 Express, Ademco High Speed, and Ademco Contact ID. Loading one of these defaults automatically programs industry standard codes that will suit most of your needs.

  • Page 29: Moving From One Page Of Programming To Another

    2. After entry into the program mode, the following will be displayed: Program Mode *Fill # View -00 3. Following this display, enter * and the first field number to be programmed. Enter the first field number to be programmed (ex. *00, installer's code) and make the desired entry.

  • Page 30: Programming System Wide Dta Fields

    Programming System-Wide Data Fields Values for some programming fields are system-wide (global), and some can be different for each partition (partition-specific). Note that the partition-specific programming fields are automatically skipped when programming the global fields. If the system has only 1 partition, the partition-specific fields will not be automatically skipped.

  • Page 31: Menu Mode Programming

    #93 Menu Mode Programming The #93 Menu Mode is a mode through which much of the system's programming is done. It offers main menu selections for the following: Zone Programming Serial Number Programming Alpha Programming Device Programming Relay Programming Relay Voice Descriptors Custom Index Programming (VIP Module substitute words) Press 0 (NO) or 1 (YES) in response to the displayed menu selection.

  • Page 32: Section 5: Installing The Keypads

    Section 5: INSTALLING THE KEYPADS This section provides the following information: • A list of wired keypads that may be used • Instructions for wiring and mounting the keypads • Instructions for addressing the keypads • A preliminary check-out procedure to ensure that the keypads are functioning properly in the system Keypads That May Be Used •...

  • Page 33: Using A Supplementary Power Supply

    4. Connect keypads to the Keypad Port terminals 6, 7, 8, and 9 on the control board, as shown in Figure 4. BLACK KEYPADS GREEN YELLOW CONTROL TERMINALS Figure 7. Keypad Connections To the Keypad Port terminals. Using a Supplementary Power Supply to Power Additional Keypads The control provides 750mA of auxiliary standby power for powering keypads and other devices from the auxiliary power output.

  • Page 34: Mounting The Keypads

    SUPPLEMENTARY CONTROL POWER SUPPLY TERMINAL STRIP – AUX AUX.DATA DATA – IMPORTANT: IMPORTANT: MAKE THESE CONNECTIONS Make connections directly to screw DIRECTLY TO terminals. Make no connection to the SCREW keypad blue wire (if present). TERMINALS AS SHOWN. Figure 8: Using A Supplementary Power Supply For Keypads Mounting the Keypads 1.

  • Page 35: Programming The Keypads

    4. After addresses are set, the green “READY” LED (or “POWER” LED on some types of keypads) should light, and the word READY (Fixed-word keypads), or DISARMED...READY TO ARM (Alpha keypads) should be displayed on keypads set to addresses 00, 01, 02, and 03. If the “Ready”...
  • Page 36 Keypads can be individually programmed to suppress SOUND OPTION arm/disarm beeps, entry/exit beeps and chime mode beeps. This helps prevent unwanted sounds from disturbing users in other areas of the premises. Enter a number 0 0 -0 3 for the keypad sounding suppression options desired for the keypad: 00 = no suppression.

  • Page 37: Section 6: Basic Hardwired Zones 1-9

    Section 6: BASIC HARDWIRED ZONES 1-9 This section provides the following information: • Common characteristics of hardwired zones • Wiring burglary and panic devices to zones 1-8 • Wiring 2-wire smoke detectors to zone 1 • Wiring 4-wire smoke detectors to zones 1-8 •...

  • Page 38: Wiring 2-Wire Smoke Detectors To Zone 1

    1. A zone must be EOLR supervised when used for fire or burglary in UL Listed Commercial Burglary installations. 2. Zone 9 is unsupervised and may not be used in UL Commercial Burglary installations 3. A closed-circuit, unsupervised zone may be used for burglary in UL Residential Burglary installations, provided that interconnecting wires no longer than three feet with no intervening walls or barriers.

  • Page 39: Compatible 2-Wire Smoke Detectors

    System Sensor 2100T Photoelectric w/B110LP base System Sensor 2151 NOTE: These smoke detectors are Listed for use with the Vista-50P and are the only 2-wire smoke detectors that may be used in UL applications. Unsupervised Usage of Zone 1 Zone 1 can also be used for normally closed, unsupervised devices by doing the following: 1.

  • Page 40: Wire Smoke Detector Power Reset Using 4204 Relay Module

    Power to 4-wire smoke detectors must be supervised (use a System Sensor A77- 716-01 EOL relay module connected as shown). RELAY – 4-WIRE PANEL SMOKE – ZONE DETECTOR (ZONE 2-8) – – PANEL AUXILIARY POWER (TERMINALS 6, 7) NOTES: NO CONNECTION •...

  • Page 41: Configuring Zone 7 For Alternate Keyswitch Function

    Configuring Zone 7 for Alternate Keyswitch Function Zone 7 may be programmed to serve as a keyswitch input. If using a keyswitch, it can be assigned to only one partition. To enable the keyswitch, do the following: 1. Enter the partition number to which the keyswitch is assigned in program field *15.

  • Page 42: Zone 9 Applications

    Compatible Glass Break Detectors Use detectors that meet the following ratings: Standby Voltage: 5VDC–13.8VDC Standby Resistance: Greater than 20k ohms (equivalent resistance of all detectors in parallel) Alarm Resistance: Less than 1.1k ohms (see note below) Alarm Current: 2 mA–10 mA Reset Time: Less than 6 seconds The IEI 735L series detectors have been tested and found to be compatible...
  • Page 43 Press 1 to enter ZONE PROGRAMMING mode. ZONE PROG? 1=YES 0=NO While in this mode, press * to display the next screen, or press # to display the previous screen. Enter the zone number to be programmed 01-09. ENTER ZN NO. 00=QUIT 02 Press * to continue.

  • Page 44: Checkout Procedure For Hardwired Zones

    02 Input Type Enter the input device type as follows: Hardwired 1:1: 0 = not used; 1=hardwired Press * to continue. The summary screen is displayed. Press * to display the "ENTER ZN NO?" prompt for programming the next hardwired zone. After all zones have been programmed, enter 00 at this prompt and press * .

  • Page 45: Polling Loop Overview

    Section 7: 2-WIRE POLLING LOOP ZONES 10 - 86 This section provides the following information: • Polling loop overview • Common characteristics of polling loop zones • Wiring RPM devices to the polling loop • Addressing RPM devices • Polling loop limitations •...

  • Page 46: Polling Loop Limitations

    When running polling loop wires, they must be at least 6" away from A.C. voltage, telephone, or intercom wiring. Since the polling loop is carrying data between the control panel and the devices, interference on this loop can cause an interruption of this communication.

  • Page 47: Polling Loop Supervision

    4197 may be powered from: POWER FOR 4197 • Panel's auxiliary power output 12VDC AT 80 MA Power wires may run up to 375 feet using 16 AWG wire • Separate supply 4197 VISTA-50P POLLING VISTA-50 VISTA-50PUL LOOP VISTA-50UL EXTENDER INPUT POLLING LOOP EXTENSION POLLING LOOP •...

  • Page 48: Programming Polling Loop Zones

    Programming Polling Loop Zones 1. With at least one two-line alpha keypad (5137AD/6139) wired and set to a proper address, power up the system temporarily by plugging the AC transformer into a 120VAC outlet (previously wired to the control). 2. Enter data field programming mode: [Installer Code] + 8 0 0. 3.
  • Page 49 Enter the input device type as follows: 10 Input Type 6=serial number polling loop device (SL type); 7=DIP switch type (left loop) polling loop device (DP type); 8=right loop of DIP switch type device (PS type). Right loops refer to the use of the right (or secondary) loop on a 4190WH zone expander module and/or 4278 PIR.

  • Page 50: Checkout Procedure For Polling Loop Zones

    6. Unplug the AC transformer and continue to the next section. 1. The 4208 must either be mounted inside the VISTA-50P cabinet or in a separate enclosure which has a tamper supervised cover. 2. The 4190WH right loop must not be used, and the left loop must be EOLR supervised.

  • Page 51: Compatible Polling Loop Devices

    Compatible Polling Loop Devices 4208 8-Zone Expander • Accommodates up to 8 zones via the polling loop. • DIP switch programmable. • The first two zones can be either normal or fast response (DIP switch selectable). • All zones are EOLR supervised (first six zones = 4.7k ohms, last two zones = 30k ohms), provided with the 4208.
  • Page 52 Compatible Polling Loop Devices 4197 Extender Module • Used to increase the polling loop current (64mA), to extend the polling loop wire run length, and/or to provide individual, electrically isolated loops. • Connects to the polling loop and is powered from panel's auxiliary power or by a separate power supply with battery backup.

  • Page 53: Section 8: Wireless (Rf) Zone Expansion

    Wireless may not be used in UL Commercial Burglary installations. Wireless Systems Available The VISTA-50P supports wireless zones which may be used exclusively or in addition to hardwire and/or polling loop zones. The system supports two different wireless systems which have many similarities, but notable differences in the programming of the transmitters for each system.

  • Page 54: Wireless System Operation And Supervision

    Wireless System Operation and Supervision • The receiver responds to status and alarm signals from wireless transmitters (@ 345MHz USA; 315MHz (5700 series) and 345 MHz (5800 series) Canada) within a nominal range of 200 feet, and relays this information to the control.
  • Page 55 Installation and Setup of the 4281/5881 Wireless Receivers 1. Mount the receiver(s). Receivers must be mounted externally to the control and can detect signals from transmitters within a nominal range of 200 feet. Take this into consideration when determining mounting location. 2.

  • Page 56: Programming The Wireless Receiver

    Installing the 5800TM Module Installation of this module is necessary only if you are using one or more 5827BD Wireless Bi-directional keypads. The 5800TM must be located between one and two feet from the 4281 or 5881 receiver's antennas. The 5800TM must not be installed within the control cabinet.

  • Page 57: House Id Sniffer Mode

    The system House ID and the Device Address of the receiver are two different things. The House ID allows the system to identify transmitters with a matching House ID. If using 5700 series wireless systems, the DIP switches on the transmitters must match the system House ID programmed into the control.

  • Page 58: Series Transmitter Setup

    5700 Series Transmitter Setup Each 5700 series transmitter has DIP switches to set both the transmitter's zone number (Transmitter ID) and the system House ID. The House ID will be the same for all transmitters and must match the House ID programmed into the system (via Device Programming) for the wireless receiver.

  • Page 59: Wireless Zone Assignments For 5700 Series Transmitters

    Wireless Zone Assignments for 5700 Series Transmitters Each wireless zone can be assigned any zone response type, such as Entry/Exit, Interior Follower, Perimeter, etc. (see the ZONE TYPES section for explanations of each zone type). For 5700 series transmitters, each response type uses a certain range of zone numbers.

  • Page 60: Compatible 5700 Series Transmitters

    Compatible 5700 Series Transmitters Model Product Zone Num. Description 5701 Panic Transmitter 62 or 63 • Programmable for either silent or audible 24 hour alarm. 5706 Photoelectric Smoke 48-55 • One piece smoke detector with built Detector in transmitter. • Built-in UL Listed 85 dB piezo electric alarm sounder and audible low battery warning.

  • Page 61: Series Transmitter Setup

    5800 Series Transmitter Setup 5800 series transmitters have built-in serial numbers that must be "learned" by the system using the # 93 Menu mode programming, or input to the control via the downloader. 5800 series transmitters (except 5827 described separately) do not have DIP switches.

  • Page 62: Compatible 5800 Series Transmitters

    • Button type transmitters (ex. 5801, 5802, 5802CP & 5803) should be periodically tested by the user for battery life. Do not install batteries in wireless transmitters until ready to learn, as will be indicated under Programming the Wireless Transmitters later in this section. Though it is not critical to remove batteries after learning, it is recommended in order to avoid interference while learning additional transmitters.
  • Page 63 Model Product Learn As Description Input Type 5816 Door/Window • Has two unique input (loop) codes: Transmitter: one for a wired closed circuit contact loop; the other for a built-in reed switch (used in conjunction with a magnet). 5816 Low Temperature •...

  • Page 64: Programming Wireless Transmitters

    Programming Wireless Transmitters Zone number assignments can be from 01-63 for 5700 series transmitters, and 01-86 for 5800 series transmitters, except for zone 64, which is reserved for a wireless keypad. 1. With at least one alpha keypad (5137AD/6139) wired and set to a proper address, power up the system temporarily by plugging the AC transformer into a 120VAC outlet (previously wired to the control).
  • Page 65 Each zone in a system must be assigned a zone 10 Zone Type type, which defines the way in which the system Zone disabled 00 responds to faults in that zone. Enter the zone response type for each zone. The screen will Refer to the ZONE automatically display the zone type for the number TYPE DEFINITIONS...
  • Page 66 If learning the serial number now (entering 1 at the 10 INPUT S/N :L last prompt), this prompt appears. Fault the and A000-0000:1 restore the transmitter (faulting is accomplished by pressing the appropriate button for button type transmitters, or by opening and closing zone sensors for other transmitters.

  • Page 67: Checkout Procedure For Wireless Zones

    Check-Out Procedure for Wireless Zones Go/No Go Test Mode Before mounting transmitters permanently, conduct Go/No Go tests to verify adequate signal strength and reorient or relocate transmitters if necessary. During this mode, wireless receiver gain is reduced by 50%. Testing in this mode assists in determining good mounting locations for the transmitters and verifies that the RF transmission has sufficient signal amplitude margin for the installed system.

  • Page 68: Output Device Basics

    Section 9: RELAY OUTPUTS & POWER LINE CARRIER (X-10) DEVICES This section provides the following information: • Output Device Basics • Wiring the 4204 relay module • Wiring the 4300 transformer • Programming the 4204 relay module • Programming output devices •...

  • Page 69: Wiring The 4300 Transformer

    4204 RELAY MODULE 4204 RELAY MODULE SWITCH 4 2 0 4 A D D R E S S S E T T I N G S POSITION ("—" means "OFF") — — — — — — — — — — —...

  • Page 70: Output Programming Options Defined

    Programming the Relay Module 1. With at least one alpha keypad (5137AD/6139 wired and set to a proper address, temporarily power up the system by plugging the transformer into a 120VAC outlet. 2. Enter data field programming mode: (Installer Code + 8 0 0 ). 3.
  • Page 71 a. EVENT (EV) is the condition (Alarm, Fault, Trouble) that must occur to a zone or group of zones (zone list) in order to activate the device. These conditions apply only when a zone list is used. The different choices for "EVENT" are listed below and in “Programming Relays &...

  • Page 72: Programming Output Devices

    The "STOP" programming determines when and under what STOP (STP): conditions the device will be de-activated. The following options are available: a. RESTORE ZONE LIST (ZL). If a "ZONE LIST" is used as the “Stop” event, the device will de-activate when all the zones in that list restore from a previous fault, trouble, or alarm condition.
  • Page 73 A relay may be activated either by an Event used in 01 Start Event conjunction with a Zone List, or by a Zone Not used Type/System Operation. If using an Event/Zone List combination, enter the event code as follows: 0=not used; 1=alarm; 2=fault; 3=trouble; 4=restore If not using a Zone List to activate the relay, enter 0.
  • Page 74 Relays may be grouped for common activation by Relay Group time driven events (commands 06-10--see Section 20: SCHEDULING OPTIONS for more information). Enter 0 (no group) or 1-8 for a specific group number. Press * to continue. The system may have some devices which are not Restriction intended to be under end user control, such as 1=yes 0=no...

  • Page 75: Zone List Programming

    Zone List Programming After all relays have been programmed, upon entering 00 at the "ENTER RELAY NO." prompt, you will be asked to enter a Zone List. If a Zone List number was used to start or stop a relay, you must define the zones belonging to that list as follows: Enter the zone list number 01-08.

  • Page 76: Relay Voice Descriptors And Custom Word Substitutes Vocabulary

    Enter the 2-digit relay/X-10 module number (01-16) ENTER RELAY NO. for the relay desired, or enter 00 to quit relay voice 00=QUIT descriptor programming mode. Press * . From the relay voice descriptor vocabulary list, enter 01 ENTER DESC d1 the 3-digit index number for the first word of the relay descriptor phrase.

  • Page 77: General Information

    Section 10: 4285 VISTA INTERACTIVE PHONE (VIP) MODULE This section provides the following information: • General information about the 4285 VIP module • Mounting and wiring the 4285 VIP module • Programming the control for 4285 VIP module access • Checkout procedure for the 4285 VIP module The 4285 VIP Module is not approved for UL installations.

  • Page 78: Wiring The 4285 Vip Module

    Do not mount the VIP Module on the cabinet door or attempt to attach it to the PC board. 2. When mounting the VIP Module outside the cabinet, use the screw holes at the rear to mount horizontally or vertically (2-faced adhesive tape may be used, if preferred).

  • Page 79: Programming 4285 Vip Module Options

    4285 WIRING NOTES: 1. Wire the 4285 VIP Module exactly as shown, using a direct-connect cord and RJ31X jack. 2. If Touch-tones are not present following phone access to the security system via an on-premises phone , try reversing the pair of wires connected to terminals 3 & 4 on the 4285, and the pair of wires connected to terminals 26 &...

  • Page 80: Custom Word Substitutes For Vip Module Annunciation

    3. From data field programming mode, press #93 to display the "ZONE PROG?" prompt. Press 0 to each menu option until "DEVICE PROG?" prompt is displayed. Press 1 to enter DEVICE PROGRAMMING mode. DEVICE PROG? 1=yes 0=no The device address identifies the device to the DEVICE ADDRESS control.

  • Page 81: Aav Module Operation

    Section 11. AUDIO ALARM VERIFICATION (AAV) UNIT This section provides the following information: • General information about the AAV option • AAV operation • Connecting an Eagle AAV Module • AAV programming requirements General Information An Audio Alarm Verification (AAV) module (also known as two-way voice), such as the Eagle 1241, is an add-on accessory that permits voice dialog between an operator at a central station and a person at the alarm installation, for the purpose of alarm verification.

  • Page 82: Programming Audio Alarm Verification Module Options

    Some AAV modules allow remote triggering by ring detection at the alarm installation. Please be advised that if this option is selected, it may defeat modem download and 4285 VIP module remote access capability. The DIP switch settings shown on the triggering diagrams disable remote AAV module trigger option.

  • Page 83: Audio Alarm Verification Module Connections

    INCOMING TELCO LINE RJ31X Notes: CALLER JACK 1.Remove any EOL ID UNIT resistor from control panel terminals 22 & on zone 5 23, if any present. 8-CONDUCTOR DOUBLE PLUG CORD (SUPPLIED) JACK VISTA-100 PREMISES ANSWERING CONTROL MACHINE AND PHONES ANSWERING MACHINE All switches should be “off”...

  • Page 84: Section 12: Voltage Triggers (Connector J7)

    Section 12: VOLTAGE TRIGGERS (Connector J7) This section provides the following information: • General information about the voltage triggers • Ground Start trigger setup • Open/Close trigger setup • Keyswitch setup • Remote keypad sounder setup • Long Range Radio setup General Information Connector J7 , located on the right hand side of the main PCB, provides 4 trigger outputs.

  • Page 85: J7 Connector For Voltage Triggers

    J7 CONNECTOR 4142TR CABLE OUT 1: GROUND START OR OPEN/CLOSE OUT 2: FIRE OR KEYSWITCH ARMED LED OUT 3: BURGLARY/AUDIBLE PANIC/AUXILIARY OUT 4: SILENT PANIC/DURESS OR KEYSWITCH READY LED Figure 20: J7 Connector For Voltage Triggers – 73 –...

  • Page 86: Ground Start Trigger Setup

    Ground Start Trigger Setup Not intended for use in UL Listed applications. . Output 1 may be used to trigger an optional 675 Ground Start module for installations having telephone lines which require ground start instead of loop start operation to obtain dial tone from the telco central office. When the panel has a message to transmit to the central station, it will seize the line, go off hook, and then trigger the 675 module to connect the "RING"...

  • Page 87: Open/Close Trigger Setup

    Open/Close Trigger Setup Output 1 may alternately be programmed to change states when the system is armed in the away mode and then disarmed. If field 1*46 is set to 1, the output will be set high when the system is in the "disarmed" state, and will switch to "0" volts when the system is armed in the "away"...

  • Page 88: Keyswitch Setup

    Programming Remote Keypad Sounding Options 1. With at least one two-line alpha keypad (5137AD/6139) wired and set to a proper address, power up the system temporarily by plugging the AC transformer into a 120VAC outlet (previously wired to the control). 2.

  • Page 89: Remote Keyswitch Wiring

    TO AUX POWER NOTE: (TERMINAL 6) The tamper switch need not be used for UL Household Fire or YELLOW WHITE Burglary installations. The GREEN tamper switch must be (ARMED) (READY) connected to an EOLR supervised zone programmed for trouble by day/alarm by 820ohms 820ohms night (type 05) response as...

  • Page 90: Auxiliary Alarm Signaling Equipment

    These triggers are programmed as the defaults for Outputs, 2, 3, and 4. These may be used to trip auxiliary alarm signaling equipment such as Ademco's 7720 and 7920SE Long Range Radios. The triggers for Fire (Output 2) and Silent Panic/Duress (Output 4) may be used to operate keyswitch armed and ready LEDs instead when field *15 is enabled.

  • Page 91: Section 13: External Sounders

    Section 13. EXTERNAL SOUNDERS This section provides the following information: • General information about external sounders • Connecting external sounders for UL and non-UL applications • Programming options for external sounders • Compatible sounders General Information The Control provides one bell relay output used to power external alarm sounders.

  • Page 92: Non-Ul Installations

    750mA is supplied by the battery. Use any UL Listed sounding device for UL Household Burglary installations. Use the Ademco AB12 Grade A bell in box for UL Commercial Burglary installations. The AB12 bell should be wired as shown in Figure 26 .
  • Page 93 Compatible Sounders Use only UL Listed sounding devices for UL installations. Outdoor Siren Self-contained siren (driver built-in) and (not UL Listed) weatherproof for outdoor use. Can be wired for either a steady or yelp sound and is rated at 120 dB @ 10 feet. This siren can also be tamper protected, or can be mounted in a metal cabinet (716), which can be tamper protected.

  • Page 94: Section 14: Event Log Options

    Section 14: EVENT LOG OPTIONS This section provides the following information: • General information about the Event Log • Event Log printer connections • Programming Event Log options • Displaying/Printing the Event Log General Information This system has the ability to record up to 224 events of various types in a history log (224 event capacity).

  • Page 95: Programming Event Log Options

    1. Printer must be configured as follows: • 8 data bits, no parity, 1 stop bit • 300 or 1200 baud (1200 preferred) • Hardware handshaking using DTR signal The 4100SM module package includes a 10 foot RS232 cable. You can use a longer cable or an extension cable if the Control and serial printer are separated by more than 10 feet.
  • Page 96 Display/Printing: After entering either the Display or Print mode, the following will be displayed: The Event Log holds up to 224 events, and can display ENTER 0 = RECENT or print all events in a category (complete), or only 1 = COMPLETE those events in a category occurring since the last Clear Event Log command (recent).
  • Page 97 Press [1] if Event Log is to be cleared from memory. CLEAR EVENT LOG All events in the log will still be displayed if the 0=NO 1=YES COMPLETE option is selected. Only those events occurring from the time of the CLEAR command will be displayed if RECENT display option is selected.

  • Page 98: Section 15: Final Power-Up Procedure

    Section 15: FINAL POWER-UP PROCEDURE This section provides the following information: • Earth ground considerations • Connecting the AC transformer • Connecting the backup battery • Programming power and AC options • Auxiliary and Polling Loop Current Draw Worksheets General Information •...

  • Page 99: Transformer And Battery Connections

    60 Hz Outlet against blowing the 3 years fuse inside the transformer (non- replaceable). TRANSFORMER 16.5VAC, 40VA ADEMCO No.1361 (IN CANADA USE No. 1361CN) or 4300 IF X-10 DEVICES WILL BE USED NOTE: WHEN POWERING UP THE PANEL, PLUG THE TRANSFORMER IN BEFORE CONNECTING THE BATTERY.

  • Page 100: Programming Power And Ac Options

    Programming Power and AC Options 1. With at least one alpha keypad (5137AD/6139) wired and properly addressed, power up the system. 2. Enter data field programming mode: [Installer Code] + 8 0 0. Program the following data fields: *17 AC POWER LOSS KEYPAD SOUNDING (1=yes; 0=no) *18 AC POWER LOSS EXTERNAL ALARM ( 1=yes;...

  • Page 101: Connecting The Battery

    Combined Auxiliary Power, Alarm Output and Polling Loop Total Current Standby Alarm Auxiliary Power Alarm Output Polling Loop TOTAL Battery Calculation Worksheet Capacity Formula Calculated Value Standby Capacity total standby load X 24 or 60 hours X 1.1 contingency factor (use total standby load from previous worksheet) Alarm Capacity total alarm load X 0.067 hours (4 minutes) (use total alarm load from previous worksheet)

  • Page 102: Section 16: False Alarm Reduction Features

    Section 16: FALSE ALARM REDUCTION FEATURES This section provides the following information: • General information about false alarms • Exit Error Logic and related reports • Exit Delay Reset • Cross-Zoning • Call Waiting Defeat General Information This control supports features which help minimize false alarms from occurring. Most false alarms occur either upon exiting the premises, or because of a zone which tends to go into alarm either due to environmental factors, or because the zone's resistance to the control may be on the edge of acceptability.

  • Page 103: Cross Zoning

    Cross-Zoning The Cross-Zoning feature is designed so that a combination of two zones must be faulted within a five minute period to cause an alarm on either zone. This prevents momentary faults from causing an alarm condition. You can select four "sets"...

  • Page 104: Section 17: Zone Type Definitions

    Section 17: ZONE TYPE DEFINITIONS This section provides the following information: • Zone number designations • Zone Type Definitions The VISTA 50 supports up to 86 zones of hard-wire, polling loop and/or wireless protection, distributed among up to 8 partitions. The following table lists the zone numbers and the types of sensors that can be used with each in this system: Zone Sensors...
  • Page 105 Type 05: Trouble by Day/Alarm by Night. Type 10 : Interior w/Delay. This zone type will give an instant alarm if faulted when This zone type gives entry and exit delays (using the armed in the Away, Stay, Instant or Maximum (night) programmed entry/exit time), if tripped when the panel modes.

  • Page 106: Section 18: Data Field Descriptions

    Section 18: DATA FIELD DESCRIPTIONS The following is a description of all data fields provided by this control. If you have followed earlier instructions during the installation of the various devices, many of these fields will already have been programmed. If you need more information about actual programming procedures, see Section 4: THE MECHANICS OF PROGRAMMING.
  • Page 107 KEYSWITCH ASSIGNMENT Enter the partition number 1-8 in which the keyswitch is being used; otherwise, enter 0. Requires the use of zone 7 wired loop (zone 7 no longer available as protection zone when used for keyswitch operation). If the keyswitch is used, the fire and panic alarm voltage triggers automatically become ARMING and READY status outputs for support of the Keyswitch LEDs.
  • Page 108 MULTIPLE ALARMS (partition-specific) Determines whether or not more than one alarm can be sounded in a given zone during an armed period. Note that multiple alarm soundings will not occur more frequently than allowed by the programmed alarm sounder duration. This selection applies to local sounding and has no impact on the number of communication messages transmitted.
  • Page 109 If selecting touch-tone, make sure the subscriber has requested and is paying for touch-tone service. Note that whether or not touch-tone dialing for call placement is permitted, communication by the use of DTMF signaling (Ademco High Speed) will still take place. See field 1*33 for Touch-Tone w/Rotary backup.
  • Page 110 | | | | | | | | | | | | | | | | | DOWNLOAD PHONE NO. This field is applicable only if downloading will be utilized. Enter the downloading phone number, up to 12 digits, 0-9; enter #11 for *, #12 for #, and #13 for a 2 sec.
  • Page 111 This field selects the reporting format for use on the primary telephone number. Enter the appropriate number for the primary format as follows: 0=Low Speed; 1=Contact ID; 2=Ademco High Speed; 3=Ademco Express LOW SPEED FORMAT (PRIMARY) Enter the appropriate value: 0=Ademco Low Speed; 1=Sescoa/Radionics...
  • Page 112 SESCOA/RADIONICS SELECT Enter 0 if Radionics format is to be used with hexadecimal 0-9, B-F reporting. Enter 1 if SESCOA format is to be used with only numeric reporting (0-9). Note that selection applies to both primary and secondary phone numbers.
  • Page 113 FIRST TEST REPORT TIME Enter the day (00-07) and time (00-23 hours/00-59 min. ) that the first test report shall be transmitted. 00 entry in all locations signifies immediately upon exiting. 00 entry in the day location will cause the report to be sent at the next occurrence of the time that is set.
  • Page 114 1*19 ARMS LOBBY (partition-specific) Enter 1 if arming this partition causes the system to attempt to arm the common lobby partition automatically. Can only arm lobby if all other affecting partitions are armed. To enable this field, field 1*18 must also be enabled.
  • Page 115 1*30 RF RCVR SUPERVISION CHECK-IN INTERVAL Enter the check-in monitoring interval in 2-hour increments. Enter 02-15 times 2 hours (4-30 hours). Failure of a receiver to receive any RF signal within the time entered will result in activation of the response type programmed for zone 90 for the first receiver and zone 88 for the second receiver and their related communication reports.
  • Page 116 1*43 PERMANENT KEYPAD DISPLAY BACKLIGHTING (partition-specific) Enter 1 if it is desired that backlighting for the keypad display remain on at all times. Enter 0 if the display should remain unlit unless a key is pressed. The backlighting then turns off again after a period of keypad inactivity.
  • Page 117 1*57 ENABLE 5800 RF BUTTON GLOBAL ARM Enter 1 to have the system arm/disarm in accordance with the button's user's global arming settings. Enter 0 if the button is not to be used to global arm the system (however, home partition arming will still occur). 1*58 ENABLE 5800 RF BUTTON FORCE BYPASS Enter 1 to allow the RF Button user to force bypass all faulted zones.
  • Page 118 2*00 NUMBER OF PARTITIONS Enter the number of partitions ( 1-8) to be used in the system. 2*01 DAYLIGHT SAVINGS TIME START/END MONTH Enter the months 00-12 in which daylight savings time starts and ends. Enter 00, 00 if daylight savings time does not apply to the user's region. Standard setting for U.S.
  • Page 119 2*11 ALLOW DISARM OUTSIDE WINDOW IF ALARM OCCURS Used only if field 2*10 (partition-specific field) is set to 1. Enter 1 to allow the system to be disarmed outside the programmed disarm (opening) window if an alarm has occurred. Enter 0 to allow disarming only during the disarm window, regardless of system status.

  • Page 120: Section 19: #93 Menu Mode Programming

    Section 19: #93 MENU MODE PROGRAMMING This section provides the following information: • #93 Menu Mode main menu options • Zone Programming • Serial Number Programming • Alpha Programming • Device Programming • Relay Programming • Relay Voice Descriptors • Custom Index Programming (VIP Module substitute words) #93 Main Menu Options The following fields should be programmed before beginning: 2*00: Number of Partitions;...
  • Page 121 Press 0 (NO) or 1 (YES) in response to the displayed menu selection. Pressing 0 will display the next choice in sequence. Refer to the ZONE PROGRAMMING section for instructions on how to program zone characteristics, the DEVICE PROGRAMMING section for instructions on how to program addressable devices, and the ALPHA PROGRAMMING section for programming alpha descriptors.
  • Page 122 Zone Types are as follows: Assign for unused zones Entry/Exit #1, burglary Entry/exit #2, Perimeter, burglary Interior, follower, burglary Trouble by day/Alarm by night, burglary 24 hour silent alarm 24 hour audible alarm 24 hour auxiliary Fire Interior, delay, burglary Arm-stay (for 5800 RF only) Arm-away (for 5800 RF only) Disarm (for 5800 RF only)

  • Page 123: Learning Serial Numbers

    If learning the serial number now (entering 1 at the 20 INPUT S/N :L last prompt), this prompt appears. Fault and restore A000-0000:1 the transmitter or polling loop device twice. The keypad will beep twice when it hears the first transmission, and three times when it hears the second.
  • Page 124 If a serial number for that device has not been Input type learned yet, and if the device assigned to that zone Input = 0 or 3-6 number has been programmed as a serial number input device in the Zone Programming menus, this prompt will appear.

  • Page 125: Programming Alpha Descriptors

    Programming Alpha Descriptors General Information • If using a 5137AD or 6139 alpha keypad in the system, you can program a user friendly English language description/location for all protection zones, relays, keypad panics, polling loop short, and RF receiver supervision troubles.
  • Page 126 a) Press [#] followed by the 3 digit number of the first word from the fixed dictionary shown later in this section (e.g., [0][1][3] for BACK). Press [6] in order to accept the word and proceed, or press [8] to store the complete descriptor and exit, or...
  • Page 127 When the desired character appears, press the [6] key to select it. The cursor will then move to the right, in position for the next character. Press [#] plus the two digit entry for the next letter of the word. OR...
  • Page 128 Custom Message Display (Installer's Message) Normally, when the system is in the disarmed state, the following display is present on the keypad. ****DISARMED**** READY TO ARM Part or all of the above message can be modified to create a custom installer message for each partition.
  • Page 129 ALPHA DESCRIPTOR VOCABULARY (For Entering Alpha Descriptors. To select a word, press [#] followed by the word's 3-digit number.) NOTE: This vocabulary is not to be used for relay voice descriptors. See the RELAY VOICE DESCRIPTORS section when programming relay voice descriptors. 000 (Word Space) ¥...

  • Page 130: Device Programming

    Device Programming This menu is used to program keypads, receivers and relay modules. From Data Field Programming mode, press #93 to display "ZONE PROG?". Press 0 repeatedly to display "DEVICE PROG?". DEVICE PROG? Press 1 to enter DEVICE PROGRAMMING mode. 1=YES 0=NO DEVICE ADDRESS The device address identifies the device to the...

  • Page 131: Relay Voice Descriptors

    Addressable keypads individually SOUND OPTION programmed to suppress arm/disarm beeps, entry/exit beeps and chime mode beeps. This helps prevent unwanted sounds from disturbing users in other areas of the premises. Enter a number 00-03 for the keypad sounding suppression options desired for the keypad as follows: 00 = no suppression.
  • Page 132 From the relay voice descriptor vocabulary list, enter the 3-digit index number for the first word of the relay 01 ENTER DESC d1 descriptor phrase. Press * to accept entry. From the relay voice descriptor vocabulary list, enter 01 ENTER DESC d2 the 3-digit index number for the second word of the relay descriptor phrase.
  • Page 133 Custom Word Substitutes for VIP Module Annunciation A substitute word can be programmed for each of the 20 custom words used in your alpha zone descriptions. This substitute word will be announced by the VIP module in place of the custom word that is displayed on the alpha keypad. For example, an alarm display of "John's Bedroom"...

  • Page 134: Section 20: Scheduling Options

    Section 20: SCHEDULING OPTIONS This section provides the following information: • Main features of scheduling • Time Window Definitions • Open/Close Schedule Definitions • Programming in the #80 Scheduling menu mode • Programming: Time Windows Open/Close Schedules Holiday Schedules Time Driven Events Access Schedules Introduction To Scheduling This section describes the scheduling features provided with this control panel.
  • Page 135 Extend Closing • A user can manually extend the arm (closing) time window Window by 1 or 2 hours. This is done by entering a keypad command (security code + #82), which then prompts the user to enter the desired extension time of 1 or 2 hours (refer to the SYSTEM OPERATION section of the Installation Instructions).
  • Page 136 Time Windows Definitions Time Windows • Scheduled events are based on time windows, which are simply periods of time during which an event may take place. Time windows are defined by a start time and stop time. The system supports up to 20 Time Windows. The windows are shared by the 8 partitions, and the windows are used for open/close schedules as well as for time driven event control.

  • Page 137: Open/Close Schedule Definitions

    Open/Close Schedule Definitions General • The Open/Close scheduling is controlled by one of three individual schedules. Each schedule consists of one time window for openings and one time window for closings. There are three types of schedules available: Daily, Holiday, and Temporary.

  • Page 138: Programming With #80 Scheduling Menu Mode

    Programming with #80 Scheduling Menu Mode The #80 Scheduling Menu Mode is used to program most of the scheduling and timed event options. To enter this mode, the system must first be in normal operating mode. Enter [Installer Code] + # + 80. The following can be programmed while in this mode: •...

  • Page 139: Basic Scheduling Menu Structure

    Basic Scheduling Menu Structure To program schedules, enter Scheduling program mode: [Installer Code] + # + 80. There are 5 sets of scheduling menus as shown below. Entering "1" at a displayed main menu prompt will select that menu set. Prompts for programming that scheduling feature will then appear.
  • Page 140 Time Windows Definitions Worksheet The system provides 20 time windows that are defined with start and stop times. These windows are used for various open/close and access schedules, as well as for output controls, and are the basis of the scheduling system. These windows are shared among all 8 partitions.

  • Page 141: Programming Time Windows

    Programming Time Windows Enter Scheduling Mode by entering the installer code + # + 80. The keypad will display the Time Window programming prompt. Enter 1 at this main menu prompt to program time Time Window ? windows. 1 Yes 0 = No Enter the 2-digit time window number to be programmed.

  • Page 142: Programming Open/Close Schedules

    Programming Open/Close Schedules Each partition can be assigned one daily open/close schedule, plus a holiday open/close schedule. Temporary schedules are programmed separately, using the #81 Temporary Schedule Menu Mode. To program additional open/close schedules, see the Time Driven Events section. After entering Scheduling Menu Mode, press 0 until the O/C Schedules prompt appears.

  • Page 143: Programming Holiday Schedules

    Holiday Definitions & Schedule Worksheet The system provides up to 16 holidays that can be assigned for the system. Each holiday can be assigned to any combination of partitions. List the desired holidays on the following worksheet. Check the partitions for which these holidays apply.

  • Page 144: Time Driven Event Worksheet

    Time-Driven Event Worksheet These are the schedules used to activate outputs, bypass zones, etc. based on a time schedule. There are 20 of these events that may be programmed for the system, with each event governed by the previously defined time windows. The actions that can be programmed to automatically activate at set times are relay commands, arm/disarm and zone bypassing commands, and open/close access conditions.
  • Page 145 Action Code Action Specifier Auto bypass - Zone list Zone list # Auto unbypass - Zone list Zone list # Open/Close Windows Activation time 3 (During) is the only valid choice for these commands. Action Code Action Specifier Enable Opening Window by partition Partition(s) Enable Closing Window by partition Partition(s)
  • Page 146 Time-Driven Event Programming The following schedules can be used to activate outputs, bypass zones, arm/disarm the system, etc. based on a time schedule. Up to 20 events can be programmed for the system. Time windows must first be defined in order to be used to trigger events.
  • Page 147 30=Auto bypass - Zone list Actions 30-31 01 ZONE LIST ? 31=Auto unbypass - Zone list Enter the zone list number which ENTER 1-8 contains the zones to be bypassed or unbypassed. Press * to accept entry. The Time Window ? prompt appears.

  • Page 148: Limitation Of Access By Time Worksheet

    Limitation of Access by Time Worksheet Limitation of Access is a means by which a user's access code is limited to working during a certain period of time.. The system provides 8 Access Schedules, each of which consists of two time windows for each day of the week and two time windows for holidays (typically one for an opening time window and the second for a closing time window).

  • Page 149: Temporary Schedule Menu Mode

    Enter the first time window number for holidays for which Hol A1 Window 1 ? 00:00 00:00 00 this access schedule applies. As the number is keyed in, the actual time that has been stored for the window will be displayed. Press * to continue. Enter the second time window number for holidays for Hol A1 Window 2 ? 00:00 00:00 00...

  • Page 150: Programming Temporary Schedules

    Arm Window Start Time HH:MM Stop Time HH:MM 8 Disarm Window Start Time HH:MM Stop Time HH:MM Arm Window Start Time HH:MM Stop Time HH:MM Programming Temporary Schedules Enter [Seecurity Code] + # + 81 to enter this mode. Note that only users with authority level of manager or higher can program temporary schedules.

  • Page 151: User Scheduling Menu Mode

    This is the prompt that actually activates the Days ? MTWTFSS temporary schedule, and allows the temporary Hit 0-7 x x schedule to be customized to a particular week's needs. To select the days which are to be activated, enter 1-7 (Monday = 1). An "X" will appear under that day, indicating the schedule for that day is active.
  • Page 152 Enter the OFF time in 00:01 - 11:59 format. 06 OFF TIME ? 11:45 PM When the display shows the desired time, press the * key to move to the AM/PM field. In this field, any of the keys 0-9 may be used to toggle the AM/PM indication. Enter 00:00 to skip.

  • Page 153: Section 21: System Communication

    86 zones of information, as well as openings and closings for all 75 users, to central stations equipped with the Ademco 685 receiver using software level 4.4 or higher. Must be level 4.6 or higher to fully support all new VISTA 50 report codes.
  • Page 154 This is the “expanded” digit. 4+2 Format Comprised of a 4-digit subscriber number and 2-digit report code. Ademco Contact ID Comprised of a 4-digit subscriber number, 1-digit event qualifier Reporting Format ("new" or "restore"), 3-digit event code, 2-digit Partition No., and 3- digit zone number, user number, or system status number.
  • Page 155 1234 5115 5555 7 (Acct #1234 with alarms on channels 2 and 3) LIMITATIONS 1. When using Ademco high speed, remember there are only 15 channels available, plus a duress channel. If more than 15 zones are being used, they will have to share channels.

  • Page 156: Loading Communication Defaults

    Loading Communication Defaults To help expedite the installation, the system provides 4 different communication defaults (Low Speed, Ademco Express, Ademco High Speed & Ademco's Contact ID ). These defaults automatically program industry-standard code assignments for zones, keypad panics, non-alarm and supervisory conditions, and can be loaded at any time without affecting non-communication program fields.
  • Page 157 ID numbers (01-86, 88-91, 95-99), Duress is sent as "DD". Alarm restore is "E" + 2nd digit. • Enables all zone type restores. ADEMCO High Speed • Selects Ademco High Speed format, with no checksum, for both phone (*94*82) numbers. • Reporting is assigned to the following channels: Channel 1 for zones 1 &...
  • Page 158 COMMUNICATION DEFAULTS for LOW SPEED FORMAT (*94*80) PRIMARY FORMAT DUAL REPORTING Ademco Low Speed LOW SPEED FORMAT (Primary) Ademco Low STANDARD/EXPANDED REPORT FOR PRIMARY Speed standard SECONDARY FORMAT Ademco Low Speed Alarm Rstr Bypass Trbl Opn/Cls Low Bat STANDARD/EXPANDED REPORT FOR SECONDARY LOW SPEED FORMAT (Sec.)
  • Page 159 COMMUNICATION DEFAULTS for ADEMCO EXPRESS FORMAT (*94*81) PRIMARY FORMAT DUAL REPORTING Ademco Express LOW SPEED FORMAT (Primary) STANDARD/EXPANDED REPORT FOR PRIMARY SECONDARY FORMAT Ademco Express standard Alarm Rstr Bypass Trbl Opn/Cls Low Bat LOW SPEED FORMAT (Sec.) STANDARD/EXPANDED REPORT FOR SECONDARY...
  • Page 160 COMMUNICATION DEFAULTS for ADEMCO HIGH SPEED FORMAT (*94*82) PRIMARY FORMAT DUAL REPORTING Ademco High Speed LOW SPEED FORMAT (Primary) STANDARD/EXPANDED REPORT FOR PRIMARY SECONDARY FORMAT Ademco High Speed standard Alarm Rstr Bypass Trbl Opn/Cls Low Bat LOW SPEED FORMAT (Sec.)
  • Page 161 COMMUNICATION DEFAULTS for ADEMCO's CONTACT ID FORMAT (*94*83) PRIMARY FORMAT DUAL REPORTING Ademco Contact ID LOW SPEED FORMAT (Primary) STANDARD/EXPANDED REPORT FOR PRIMARY SECONDARY FORMAT Ademco Contact ID standard Alarm Rstr Bypass Trbl Opn/Cls Low Bat LOW SPEED FORMAT (Sec.)

  • Page 162: Section 22: Downloading Primer

    Downloading allows the operator to remotely access, program, and control the security system over normal telephone lines. Anything that can be done directly from the keypad can be done remotely, using ADEMCO's VLINK ® downloading software. To communicate with the control panel, the following is required: 1.

  • Page 163: On-Line Control Functions

    1. The computer calls up the Control panel. (The phone number for each customer is entered into the customer's account file on the computer). 2. The Control panel "answers" at the pre-programmed ring count and executes a handshake with the computer. 3.

  • Page 164: Access Security

    Access Security Accessing the Control from a remote location is protected against compromise by the use of 4 levels of protection: 1. Security Code Handshake: The subscriber's account number as well as an 8- digit ID number (known only to the office) must be matched between the Control and computer.

  • Page 165: Connecting A 4100Sm Module For Direct Wire Downloading

    Connecting a 4100SM Module for Direct Wire Downloading The Control can be downloaded without using a modem or telephone line by using VLink ® Software and a 4100SM Serial Module. The direct wire downloading connection is to be temporary, and is not part of the permanent installation.

  • Page 166: Section 23: Setting The Real-Time Clock

    Section 23: SETTING THE REAL-TIME CLOCK This section provides the following information: • General information about the real-time clock • Setting the time and date General Information This system provides a real-time clock, which must be set in order for the system's event log to keep track of events by time and date.

  • Page 167: Section 24: Security Access Codes

    Section 24: SECURITY ACCESS CODES This section provides the following information: • General information about security access codes • Definition of user authority levels • How to add a user access code • How to change a user access code •...
  • Page 168 Open/Close Reporting Note: When adding a user, the system will only prompt for Open/Close reporting capability if the user is being added by the Installer. When a Master or Manager adds a new user, the new user's Open/Close reporting enable will be the same as that of the Master or Manager adding the user.
  • Page 169 Make sure the end user understands this requirement. Temporary codes are entered as 4-digit numbers. Ademco Contact ID format is capable of reporting Users 01-75 uniquely. If any other report format is used, only user numbers #1 - #15 can uniquely report to the central station.

  • Page 170: To Add, A Master, Manager Or Operator Code

    EXAMPLE OF MULTIPLE PARTITION ACCESS Part 1 Part 2 Part 3 Part 4 Part 5 Part 6 Part 7 Part 8 User 3 User 3 Level 1 Level 4 Master Oper B In the above example, User 3 has MASTER authority in partition 1 and OPERATOR B authority in partition 2.

  • Page 171: To Change A Master, Manager, Or Operator Code

    Press 0 (NO) if the user is to have access to this partition Multi-Access ? only. Press 1 (YES) if the user is to have access to 0 = NO , 1 = YES more than one partition. If NO, the program exits this mode.

  • Page 172: Adding An Rf Key To An Existing User

    Adding An RF Key To An Existing User To add an RF key to an existing user, or to change a user's global arm option, first delete that user's code, then re-add the user code as described in the "Add A User"...

  • Page 173: Section 25: Keypad Functions

    Section 25: KEYPAD FUNCTIONS This section provides the following information: • General information about keypad usage • Basic keypad functions • Global arming • Access control • Delaying closing time • Executing the "Go To" command • Viewing: A user's capabilities Zone descriptors Downloaded messages Built-in user's guide...

  • Page 174: Global Arming

    Quick Arming: Note that if QUICK ARM is enabled (field *29), the # key can be pressed instead of entering the security code, for any of the arming procedures (Away, Stay, Instant, Maximum, etc.). User #02 must be programmed into the system in order for the Quick Arm feature to work.

  • Page 175: Access Control

    Access Control If programmed, one relay may be used for access control in each partition. The relay is programmed in data field 1*76. To activate this relay, the user enters his user code + 0 . The relay will pulse for 2 seconds. Delaying Closing Time If Open/Close schedules are used, end users can manually delay closing time by extending the closing window by 1 or 2 hours.

  • Page 176: Viewing Downloaded Messages

    Viewing Downloaded Messages Users may occasionally receive a message from their installation company displayed on an alpha keypad. When this occurs, the keypad will display "Message. Press 0 for 5 secs.". Instruct the user to press and hold the 0 key to display the central station's message.

  • Page 177: Manual Relay Activation Mode (#70)

    To program that speed key sequence, type the following : *2 D 61011 D 4 D *1 D D Note that the "D" key is pressed after the "2," the last "1" and the "4," separating the different commands. Press "D" twice to complete the entry and exit. To execute a speed key sequence, press the "D"...

  • Page 178: Section 26: Testing The System

    Section 26: TESTING THE SYSTEM This section provides the following information: • Using Test Mode • Turning the system over to the user • Trouble conditions Using Test Mode General Information After the installation is completed, thoroughly test the Security System on a partition by partition basis as follows: 1.

  • Page 179: Armed System Test

    Armed System Test 1. A message will be sent to the central station during the following tests. Notify the central station that a test will be in progress. 2. A display of "COMM. FAILURE" (FC on fixed work keypads) indicates a failure to communicate (no Kissoff by the receiver at the central station after the maximum number of transmission attempts is tried).

  • Page 180: Trouble Conditions

    Trouble Conditions The word "CHECK" on the keypad's display, accompanied by a rapid "beeping" at the keypad, indicates that there is a trouble condition in the system. The audible warning sound can be silenced by pressing any key. Instruct users to call for service immediately upon seeing any of the following messages.
  • Page 181 Other System Messages • "COMM. FAILURE" (alpha) or "FC" (fixed-word) at the Keypad Indicates that a failure occurred in the telephone communication portion of your system. • "LO BAT" (alpha) or "BAT" (fixed-word) and a zone descriptor, accompanied by a once per minute beep at the Keypad Indicates that a low battery condition exists in the wireless transmitter displayed.

  • Page 182: Regulatory Agency Statements

    (Also see MOUNTING THE CABINET section) 4. Wire an Ademco AB12 Grade A Bell/Box to the bell output. Bell wires must be run in conduit. Program the bell output for 16 or more minute timeout and for confirmation of arming ding.
  • Page 183 • Maximum auxiliary current is 300mA (including polling loop current) • Use 14AH battery (Yuasa model NP7-12 recommended, use two connected in parallel. A dual battery harness is provided with Ademco No. 4100EOLR Resistor kit (kit also contains EOL resistors having spade lug/heat shrink tubing construction which has been approved by UL and CSFM for fire zone usage).
  • Page 184 "FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENT" This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information: This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause interference to radio and television reception.
  • Page 185 CANADIAN DEPARTMENT OF COMMUNICATIONS (DOC) STATEMENT NOTICE The Canadian Department of Communications label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements. The Department does not guarantee the equipment will operate to the user's satisfaction. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company.

  • Page 186: Dip Switch Tables

    DIP SWITCH TABLES DIP SWITCH TABLES FOR ADDRESSABLE POLLING LOOP DEVICES 4192D/4192SDT/4192CP 4190WH ZONE EXPANDER 4208 ZONE EXPANDER SMOKE DETECTORS SIDE VIEW SHOWN SET FOR (UP) ID 10 (A) SIDE VIEW APPLIES TO TABLE A UPLY APPLIES TO TABLE A & B UPLY (UP) 1 2 3 4 5 SHOWN SET FOR ID 10...

  • Page 187: Surface Mount

    DIP SWITCH TABLES FOR POLLING LOOP DEVICES 4278 PIR 4194 REED CONTACT 4275 PIR (SURFACE MOUNT) MIRROR MIRROR SHOWN SET FOR SHOWN SET FOR SIDE VIEW SHOWN SET FOR ID 10 ID 10 (A) ID 10 (DN) SIDE VIEW SIDE VIEW 1 2 3 4 5 6 (DN) 1 2 3 4 5 6 7 8...

  • Page 188: Dip Switch Tables For 5700 Rf System Wireless Devices

    DIP SWITCH TABLES FOR 5700 RF SYSTEM WIRELESS DEVICES 5775 PIR HOUSE ID 5701 PANIC TRANSMITTER 5706/5707 SMOKE DETECTOR/TRANSMITTER SWITCH SETTING FOR ALL DETECTORTRANSMITTER DEVICES EXCEPT 5716 MIRROR HOUSE ID (1 SHOWN) DIP SWITCH POSITION DEVICE SIDE 1 2 3 4 5 6 VIEW (UP) —...

  • Page 189: Summary Of System Commands

    SUMMARY OF SYSTEM COMMANDS Event Logging Commands Event Log Display = Code+[#] + 60 (Alpha keypad only) Event Log Print = Code + [#] +61 (Installer Only) Clear Event Log = Code + # + 62 (Installer Only) Wireless System House Id Sniffer Mode=Code + [#] + 2 (Installer Only) Commands Transmitter Id Test= Code + [#] + 3 (Installer Only)

  • Page 190: Specifications

    14-1/2"W X 18"H X 4.3"D (VISTA 50PUL) Electrical: VOLTAGE INPUT: From Ademco No. 1361 Plug-In Transformer (use 1361CN in Canada) or 4300 transformer (for X-10 installations) rated 16.5VAC, 40 VA. ALARM SOUNDER OUTPUT: 10VDC-13.8VDC, 2.8 amps max., (UL1023, UL609 installations); 750mA less aux.

  • Page 191: Contacting Technical Support

    ¥ Note the proper model number of this product, and the version level (if known) along with any documentation that came with the product. ¥ Note your ADEMCO customer number and/or company name. Having this information handy will make it easier for us to serve you quickly and effectively.
  • Page 192 Ademco 4+2 Express ....144, 178 4+2 Format ..........142 Device Programming ..23, 44, 58, 68, 118 Ademco Contact ID ..142, 144, 157, 178 4100SM ........16, 82, 153 Dial Tone Detection ........99 Ademco High Speed ..... 144, 178 4137AD ........
  • Page 193 Interior, Follower ........92 REPORT CODES FOR ZONES 65-80 ...103 Time-Driven Event Worksheet ....132 J7 ............82 RESPONSE TYPES ......101 timers ............. 139 J8 ............. 82 RESTORE REPORT TIMING ....101 TOUCH-TONE OR ROTARY DIAL ..97 Keypad Connections ....... 21 Restrict ............123 TOUCH-TONE W/ROTARY Keypad Panic Enables ......
  • Page 194 WARNING! THE LIMITATIONS OF THIS ALARM SYSTEM While this System is an advanced wireless security system, it does not offer guaranteed protection against burglary, fire or other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a vari- ety of rea sons.
  • Page 195 N.C. Instructions for Connect to good earth 60 Hz Outlet required ground to maintain im- Telephone connections capacity munity to transients. using Ademco No. 620 REMOTE KEYPAD See Instructions for RJ31X direct connect Replace Use 4137AD/6137/6128 N.O. N.O. N.O. N.O.
  • Page 196 18 months from the date stamp con trol on the product or, for products not having an Ademco date stamp, for 12 months from date of original purchase unless the installation instructions or catalog sets forth a shorter period, in which case the shorter period shall apply.

This manual is also suitable for:

Vista-50pul

Table of Contents

Save PDF