Table of Contents
Advertisement
9. Audio Level Indicator (AUDIO LEVEL)
This Indicator indicates the audio output level of the
Program Out 1 Audio Output Connector (135) and the
Program Out 2 Audio Output Jacks (134)
10. Matte Colour Control (LEVEL)
The colour displayed on the Matte Colour Indicator (11)
can be adjusted with this control except C/L BAR
11. Matte Colour Indicator
The Matte Colour selected by the Matte Colour
Selectors (13) is shown by the appropriate LED
12. Graduation Button (GRADUATION)
When this button is pressed, the Matte colour of
the upper portion on the screen is less intense and
gradually increases to that of the lower portion of the
screen
13. Matte Colour Selectors (SELECT)
Any one of 9 Matte Colours Colour Bar, White, Yellow,
Cyan, Green, Magenta, Red, Blue and Black - can
be selected by repeatedly pressing either of these
buttons
When the SELEC r ( ) button is pressed,
the colour indicated on the Matte Colour Indicator
(11) changes from lower to upper. The Black will be
selected after the Colour Bar. When the SELECT ( )
button is pressed, the reverse procedure takes place.
14. Event Number Buttons (EVENT NO)
These buttons are used to memorize the present status
of all functions settings on the unit Also this button can
be used with the Auto Take Button (97) to recall the
memorized status Each button has 2 memories (by
using Shift Button (18)) Up to 8 memories are availabe
with these 4 buttons
Note:
Refer to the Shift Button (18) and the Memory Set
Button (19) for selection of preset memory settings
15. Program Out - A Button (A)
When this button is pressed, the A - bus source signals
which is given Effect by the DIGITAL EFFECT function,
COLOUR CORRECTION function, SCENE GRABBER
function, COMPRESSION function or SLIDE function is
provided at the Program Output connectors
Note:
If the MATTE on the A - bus is pressed, the A - bus
button will begin blinking automatically to show
you which button was selected before.
16. Program Out - B Button (B)
When this button is pressed, the B - bus source signals
which is given Effect by the DIGITAL EFFECT function,
COLOUR CORRECTION function, SCENE GRABBER
function, COMPRESSION function or SLIDE function is
provided at the Program Output connectors
Note :
If the MATTE on the B - bus is pressed, the B - bus
button will begin blinking automatically to show
you which button was selected before
17. Effect - Out Button (EFFECT)
When this button is pressed, the final video signal -
whether it is effected or not will be provided at the
Program Output connector.
18. Shift Button (SHIFT)
This button will be used when the Event Number
Buttons (14) numbered 5 to 8 are required However,
in case this button is pressed with the Memory Set
Button (19) simultaneously, the unit then enters the
Special Mode (SPECIAL MODE)
Notice :
(1) Refer to page 35 for details of the Special Mode
(2) In the Special Mode, the LED on the Shift Button
(18) goes off and the one on the Memory Set
Button (19) starts blinking
19. Memory Set Button (MEMORY)
This button has 2 functions In order to activate the
Event Number Buttons (14) to memorize the current
status of the unit, press the Memory Set Button
(19) prior to the Event Number Buttons (14)
case this button is pressed with the Shift Button
(18) simultaneously (as mentioned previously), the unit
enters the Special Mode
Notice :
(1)
Refer to page 35 for details of the Special Mode
(2) In Special Mode, the LED
goes off and the one on the Memory Set Button
(19) starts blinking
20. Multi Mode Indicator (MULTI MODE)
The number displayed on this indicator shows the mode
of the pattern by pressing the Multi Wipe Button (67)
From 0 to 6 will be indicated
21. Auto Fade Time Indicator (AUTO FADE TIME)
The number on the indicator shows the fading time by
picture frame when adjusting the Auto Fade Transition
Control (91)
From 0 to 510 will be indicated for every 2 frames.
22. Pattern Mode Indicator (PATTERN MODE)
The number on this indicator shows the pattern mode
which is pressed and selected from the Wipe Pattern
Select Buttons number (60), (61), (62), (64), (66), (68) or
(70)
From 1 to 4 will be indicated
23 Auto Take Time Indicator (AUTO TAKE TIME)
The number on this indicator shows the Auto Take
Time by picture frame when adjusting the Auto Take
Transition Control (98)
From 0 to 510 will be indicated for every 2 frames
24. Wipe Pattern Number Indicator (WIPE PATTERN)
The number on this indicator shows the wipe pattern
which is generated by the combinations of the Wipe
Pattern Select Buttons number (60), (61), (62), (64), (66),
(68) or (70), and Modify Buttons number (63), (65), (67),
(69) or (71)
Any possible combination from 1 to 255 will be
indicated
- 5 -
In
on the Shift Button (18)
Hide quick links:
Advertisement
Table of Contents
