Table of Contents
Advertisement
H. Application
H-1. Event Memory Functions
Customized effect combinations can be stored in
the Event Memory, and later recalled tor subsequent
access. The MEMORY Button (19) and SHIFT Button
(18) are used to store the desired effects.
•
To clean/reset the eight memories
Press OPERATE Button (1) to turn off
holding down both MEMORY Button (19) and SHIFT
Button (18) press OPERATE Button (1) to turn on again
•
To set a Memory location
Choose desired effects on panel. When the correct
combination is selected press MEMORY Button (19)
then press the appropriate EVENT NO Button (14) (for
location 5-8, press SHIFT Button (18)) The LED on the
EVENT NO Button (14) blinks 3 times then goes off
when memory is completed.
• To recall an event setting, press (for 5 8 press SHIFT
Button (18), then) the correct EVENT NO Button (14)
then press the AUTO TAKE Button (97).
Note:
Up to eight pre-set Event combinations are
available
If executing Auto Take successively,
each memory occurance will be performed in
sequence according to the numerical locations
used, ie
only stored numbers will be "toggled"
through. So if #3 was skipped in the event memory
setting, it will also be skipped by pressing AUTO
TAKE Button (97).
Caution :
The event memory will disappear in a few days
leaving the Main Power Switch (131) off
Then, while
Memonzed to No 1
oi No 5
- 3 5 -
H-2. Special Mode Functions
Under ' Special Mode eight factory preset effect
functions are accessible for use. These demonstrate a
few of the many capabilities of the instrument.
Note:
Before operating the Mode 6-Shutter, Mode
7-Vibrate or Mode 8 Satellite, be sure to turn the
Mix/Wipe Lever (99) to the B bus position
• Simultaneously press the MEMORY Button (19) and
SHIFT Button (18) The MEMORY Button (19) LED will
begin blinking indicating that the instrument is in Special
Mode
• Each mode is accessed (when MEMORY Button (19)
LED is blinking) by pressing (for 5-8, press SHIFT Button
(18)) the appropriate EVENT NO Button (14)
(1) Mode 1 - Mosaic Mix
Press No 1 button. The mix pattern from A-bus
and B bus becomes a mosaic during the m.ix
This can be executed by the Mix/Wipe Lever
(99) or by Auto Take Button (97) or by external
controller equipped with GPI (or RS422).
(2) Mode 2 - Stream
Press No 2 button. The compressed image
zooms in from corne.r
available by the Positioner Joystick (.2) This
can be executed by the Mix/Wipe Lever (99)
or by Auto Tdke Button (97) or by external
controller equipped with GPI (or RS422).
(3) Mode 3 - Cork Screw
Press No 3 button The compressed image
corkscrews in from corner
executed by the Mix/Wipe Lever (99) or by
Auto Take Button (97) or by external controller
equipped with GPI (or RS422)
(4) Mode 4 - Bounce
Press No 4 button The compressed image
drops bounce in from corner
executed by the Mix/Wipe Lever (99) or by
Auto Take Button (97) or by external controller
equipped with GPI (or RS422)
(5) Mode 5 - Flip
Press No 5 button.
Compressed Wipe is obtained on the Matte
Colour.
This can be executed by the
Mix/Wipe Lever (99) or by Auto Take Button
(97) or by external controller equipped with
GPI (or RS422).
(6) Mode 6 - Shutter
Press N06 button. The Horizontal Split Wipe
from B-bus to Matter Colour is obtaine.d This
can be executed using either the Auto Take
Button (97) or by external controller equipped
with GPI.
Two corners are
This can be
This can be
The Vertical Split
Hide quick links:
Advertisement
Table of Contents
