Operating Instructions - Jensen VM9312HD Installation And Operation Manual

VM9312HD

OPERATING INSTRUCTIONS

Power On / Off
Press the /SRC button (6) on the unit (or the
on the remote control) to turn the unit on. The buttons on the
front of the unit light up and the current mode status appears
in the LCD (7). You can also turn on the unit by pressing the
OPEN button (1) and opening the TFT screen.
Press and hold the button to power off the unit.The monitor
is drawn back into the main compartment.
Audible Beep Confirmation
An audible beep tone confirms each function selection. The
Beep tone can be disabled through the Setup menu.
Mute
Press the MUTE button (8) on the front panel or the MUTE
button (3) on the remote to mute the volume from the unit.
Press the MUTE button again to restore the volume. "MUTE"
is displayed on the LCD. Adjusting the volume or using any of
the audio setup features cancels the mute function.
Playing Source Selection
Press the SRC button (6) on the front panel or the SRC
button (8) on the remote to change between available playing
sources in the following order: AM/FM, DISC, AUX IN1, AUX
IN2, SAT, and CAMERA. The playing mode is displayed on
the TFT and LCD screens.
External peripheral devices can be connected to this unit via
RCA output or MediaLink. Select "AUX-IN1" or "AUX IN2"
mode to access and control connected auxiliary devices.
Volume Adjustment
To increase or decrease the volume level, turn the rotary
encoder (5) on the front panel or press the VOL+/ VOL-
buttons (15, 16) on remote control. When the volume level
reaches "0" or "40", a beep sounds, indicating that the
adjustment limit has been reached. The volume ranges from
"0" to "40". The LCD or TFT screen displays the volume level
for 3 seconds.
Steering Wheel Control (SWC)
The VM9312HD is compatible with the PAC (Pacific
Accessory Corporation) steering wheel control adapter SWI-
PS. A 3.5mm female connector (labeled "SWC Interface") on
the back of the head unit allows connectivity to the PAC
adapter. Please refer to the instructions included with the
PAC adapter for detailed installation information.
SWC Functions
The following controls are available for most vehicles:
button (4)
1. Vol Up
2. Vol Down
3. Mute
4. Seek Up / Next Track / ** Preset Up
5. Seek Down / Previous Track / ** Preset Down
6. SRC (Source)
7. ** Select
8. ** Select
9. Band
** If additional steering wheel control buttons are available on
the vehicle, function 7 / 8 may be assigned the "Select"
feature. This feature / function may not be available on some
vehicles.
Select Operation
If "Select" (function 7 or 8) is held down and function 4 is
pressed momentarily, Preset Up will be selected. If "Select"
(function 7 or 8) is held down and function 5 is pressed
momentarily, Preset Down will be selected.
Audio Control Menu
The Audio Control feature allows you to easily adjust your
audio system to meet the acoustical characteristics of your
vehicle, which vary depending on the type of vehicle and its
measurements. Proper setting of the Fader and Balance
boosts the effects of the cabin equalizer.
Press the AUDIO button (5) on the front panel once to display
the audio menu.
EQ User
+14 —
0 —
–14 —
BASS MID TREB
User
To adjust an audio feature:
1. Use the touchscreen, press the (>>|)/(|
22) on the remote control, or use the joystick to highlight
the audio feature to be adjusted.
2.
3.
EQ
BASS
MID
TREB
SUB
BAL–FAD
NOTE: The EQ mode will automatically change to
"USER" when individual audio functions are adjusted.
The Audio menu will automatically exit after a few seconds of
inactivity. To exit quickly, touch the top left corner of the
screen or press and hold the AUDIO button (5).
FAD BAL
F
System Reset
0 —
To correct a system halt or other illegal
operation, use the tip of a pen to press
L R
—
the reset button (12) located on the
front bottom-right corner of the unit. After a system reset, the
–14 —
unit restores all factory default settings.
R
SUB
NOTE: If the unit is reset while a DVD is playing, the DVD
resumes play once the reset is complete.
Line Mute
) buttons (14,
<<
If the "MUTE" wire is connected, audio output mutes when a
telephone call is received by the car phone or when verbal
navigation is performed.
12
Touch the screen or press the joystick button (13) to
select the highlighted option.
Touch the +/– buttons on the screen, press the |<<, >>|,
>>, or << buttons (17, 19, 14, 22) on the remote control,
or use the joystick to adjust the selected feature to the
desired setting.
Table 4: Audio Adjustments
Audio Function Adjustable Range
User
Acoustic
Urban
Rave
Latin
Dance
Hip Hop
Rock
-14 to +14
-14 to +14
-14 to +14
-14 to 0
Grid
[RESET] Button