Download Print this page

Lenovo ThinkPad X200si Hardware Maintenance Manual

Lenovo thinkpad notebooks hardware maintenance manual.
Hide thumbs

Advertisement

www.battery-adapter.com
Removing and replacing a FRU
This chapter presents directions and drawings for use in removing and replacing a
FRU. Be sure to observe the following general rules:
1. Do not try to service any computer unless you have been trained and certified.
2. Before replacing any FRU, review "FRU replacement notices" on page 79.
3. Begin by removing any FRUs that have to be removed before the failing FRU.
4. Follow the correct sequence in the steps for removing the FRU, as given in the
5. When turning a screw to replace a FRU, turn it in the direction as given by the
6. When removing the FRU, move it in the direction as given by the arrow in the
7. To put the new FRU in place, reverse the removal procedure and follow any
8. When replacing a FRU, use the correct screw as shown in the procedures.
DANGER
Before removing any FRU, turn off the computer, unplug all power cords
from electrical outlets, remove the battery pack, and then disconnect any
interconnecting cables.
Attention: After replacing a FRU, do not turn on the computer until you have
made sure that all screws, springs, and other small parts are in place and none are
loose inside the computer. Verify this by shaking the computer gently and listening
for rattling sounds. Metallic parts or metal flakes can cause electrical short circuits.
Attention: The system board is sensitive to, and can be damaged by, electrostatic
discharge. Before touching it, establish personal grounding by touching a ground
point with one hand or by using an electrostatic discharge (ESD) strap (P/N
6405959).
© Copyright Lenovo 2008, 2010
An untrained person runs the risk of damaging parts.
Any such FRUs are listed at the top of the page. Remove them in the order in
which they are listed.
drawings by the numbers in square callouts.
arrow in the drawing.
drawing.
notes that pertain to replacement. For information about connecting and
arranging internal cables, see "Locations" on page 161.
www.battery-adapter.com
83

Advertisement

   Related Manuals for Lenovo ThinkPad X200si

   Summary of Contents for Lenovo ThinkPad X200si

  • Page 1

    Attention: The system board is sensitive to, and can be damaged by, electrostatic discharge. Before touching it, establish personal grounding by touching a ground point with one hand or by using an electrostatic discharge (ESD) strap (P/N 6405959). © Copyright Lenovo 2008, 2010 www.battery-adapter.com...

  • Page 2

    www.battery-adapter.com Before servicing ThinkPad X200, X200s, X200si, X201, X201i, and X201s Removing the SIM card: Some models of the ThinkPad X200, X200s, X200si, X201, X201i, and X201s you are servicing might have the SIM card that the customer has been installed. If the computer you are servicing has the SIM card, remove it before you start the servicing.

  • Page 3: Battery Pack

    The only exception to this is if the battery pack is physically damaged or a customer is reporting a possible safety issue. If ThinkVantage Toolbox or Lenovo System Toolbox is not installed in the computer, the customer should download this program before a non-physically damaged battery pack is replaced.

  • Page 4

    www.battery-adapter.com Table 9. Removal steps of battery pack DANGER Use only the battery specified in the parts list for your computer. Any other battery could ignite or explode. Unlock the battery release lever 1 . Holding the battery release lever in the unlocked position 2 , remove the battery pack in the direction shown by arrow When installing: Install the battery pack along the slide rails of the slot.

  • Page 5

    www.battery-adapter.com 1020 Hard disk drive (HDD) cover, HDD, and HDD rubber rails or solid state drive (SSD) and storage converter For access, remove this FRU: v “1010 Battery pack” on page 85 Attention: v Do not drop the hard disk drive or apply any physical shock to it. The hard disk drive is sensitive to physical shock.

  • Page 6

    www.battery-adapter.com Table 10. Removal steps of HDD cover, HDD, and HDD drive rubber rails or SSD and storage converter (continued) When installing: Make sure that the HDD connector or SSD connector is attached firmly. ThinkPad X200, X200s, X200si, X201, X201i, and X201s Hardware Maintenance Manual www.battery-adapter.com...

  • Page 7

    www.battery-adapter.com Table 10. Removal steps of HDD cover, HDD, and HDD drive rubber rails or SSD and storage converter (continued) HDD and HDD rubber rails: When installing: The rubber rails on the hard disk drive must be attached to the replacement drive. Otherwise the drive cannot be installed properly. SSD and storage converter: Removing and replacing a FRU www.battery-adapter.com...

  • Page 8

    www.battery-adapter.com Table 10. Removal steps of HDD cover, HDD, and HDD drive rubber rails or SSD and storage converter (continued) When installing: When you install the SSD in the storage converter, do as follows. ThinkPad X200, X200s, X200si, X201, X201i, and X201s Hardware Maintenance Manual www.battery-adapter.com...

  • Page 9

    www.battery-adapter.com 1030 DIMM For access, remove this FRU in order: v “1010 Battery pack” on page 85 Table 11. Removal steps of dimm Remove the DIMM slot cover as shown in this figure. Note: Loosen the screws 1 , but do not remove them. Removing and replacing a FRU www.battery-adapter.com...

  • Page 10

    www.battery-adapter.com Table 11. Removal steps of dimm (continued) Note: For ThinkPad X200, X200s, and X200si, if only one DIMM is used on the computer you are servicing, the card must be installed in SLOT-0 ( a ), but not in SLOT-1 ( b ). For ThinkPad X200, X200s, and X200si: ThinkPad X200, X200s, X200si, X201, X201i, and X201s Hardware Maintenance Manual www.battery-adapter.com...

  • Page 11

    www.battery-adapter.com Table 11. Removal steps of dimm (continued) For ThinkPad X201, X201i, and X201s: When installing: Insert the notched end of the DIMM into the socket. Press the DIMM firmly, and pivot it until it snaps into the place. Make sure that it is firmly fixed in the slot and does not move easily.

  • Page 12: 1040 Keyboard

    www.battery-adapter.com 1040 Keyboard For access, remove this FRU in order: v “1010 Battery pack” on page 85 Table 12. Removal steps of keyboard Step Icon Screw (quantity) Color Torque M2 × 5 mm, wafer-head, Black 0.181 Nm nylon-coated (4) (1.85 kgfcm) ThinkPad X200, X200s, X200si, X201, X201i, and X201s Hardware Maintenance Manual www.battery-adapter.com...

  • Page 13

    www.battery-adapter.com Table 12. Removal steps of keyboard (continued) Lift the keyboard a little in the direction shown by arrow 4 , and then detach the connector 5 . Removing and replacing a FRU www.battery-adapter.com...

  • Page 14

    www.battery-adapter.com Table 12. Removal steps of keyboard (continued) When installing: 1. Attach the keyboard connector firmly. 2. Make sure that the keyboard edges are under the frame as shown in this figure. Then press the keys to latch the keyboard firmly in place. 3.

  • Page 15: 1050 Palm Rest Or Palm Rest With Fingerprint Reader

    www.battery-adapter.com 1050 Palm rest or palm rest with fingerprint reader For access, remove this FRU in order: v “1010 Battery pack” on page 85 v “1040 Keyboard” on page 94 Note: In models with the fingerprint reader, the sensor is attached to the palm rest FRU.

  • Page 16

    www.battery-adapter.com Table 13. Removal steps of palm rest (continued) Note: Step 2 is only for models with the fingerprint reader. For models without the fingerprint reader, skip step 2 . ThinkPad X200, X200s, X200si, X201, X201i, and X201s Hardware Maintenance Manual www.battery-adapter.com...

  • Page 17

    www.battery-adapter.com Table 13. Removal steps of palm rest (continued) When installing: 1. In models with the fingerprint reader, attach the fingerprint reader connector firmly to the system board. 2. Press the left and right top edges of the palm rest to fit it into place. 3.

  • Page 18: Backup Battery

    www.battery-adapter.com 1060 Backup battery DANGER Use only the battery specified in the parts list for your computer. Any other battery could ignite or explode. For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1040 Keyboard” on page 94 v “1050 Palm rest or palm rest with fingerprint reader”...

  • Page 19

    www.battery-adapter.com Table 14. Removal steps of backup battery (continued) When installing: Make sure that the battery connector is attached firmly. Removing and replacing a FRU www.battery-adapter.com...

  • Page 20: Table Of Contents

    www.battery-adapter.com 1070 PCI Express Mini Card for wireless LAN/WiMAX For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1040 Keyboard” on page 94 v “1050 Palm rest or palm rest with fingerprint reader” on page 97 Table 15.

  • Page 21

    www.battery-adapter.com Table 15. Removal steps of PCI Express Mini Card for wireless LAN/WiMAX (continued) When installing: v In models with wireless LAN card that has two antenna connectors, plug the gray cable into the jack labeled MAIN or M on the card, and the black cable into the jack labeled AUX or A.

  • Page 22: Them In Direction Of The Arrow

    www.battery-adapter.com Table 15. Removal steps of PCI Express Mini Card for wireless LAN/WiMAX (continued) Harf size PCI Express Mini Card: In step 1 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow.

  • Page 23: Pci Express Mini Card For Wireless Wan

    www.battery-adapter.com 1080 PCI Express Mini Card for wireless WAN For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1040 Keyboard” on page 94 v “1050 Palm rest or palm rest with fingerprint reader” on page 97 Table 16.

  • Page 24

    www.battery-adapter.com Table 16. Removal steps of PCI Express Mini Card for wireless WAN (continued) When installing: Plug the red cable into the jack labeled MAIN on the card, and the blue cable into the jack labeled AUX. ThinkPad X200, X200s, X200si, X201, X201i, and X201s Hardware Maintenance Manual www.battery-adapter.com...

  • Page 25: For Access, Remove These Frus In Order: V "1010 Battery Pack

    www.battery-adapter.com 1090 Intel Turbo Memory Minicard or Wireless USB PCI Express Half-Mini Card For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1040 Keyboard” on page 94 v “1050 Palm rest or palm rest with fingerprint reader” on page 97 Table 17.

  • Page 26

    www.battery-adapter.com Table 17. Removal steps of Intel Turbo Memory Minicard or Wireless USB PCI Express Half-Mini Card (continued) When installing: In models with the Wireless USB PCI Express Half-Mini Card, plug the yellow cable into the jack on the card. ThinkPad X200, X200s, X200si, X201, X201i, and X201s Hardware Maintenance Manual www.battery-adapter.com...

  • Page 27: Keyboard Bezel

    www.battery-adapter.com 1100 Keyboard bezel For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1040 Keyboard” on page 94 v “1050 Palm rest or palm rest with fingerprint reader” on page 97 Table 18. Removal steps of keyboard bezel Step Screw (quantity) Color...

  • Page 28

    www.battery-adapter.com 1110 Monaural speaker assembly (for X200, X200s, X201s, and X201si) For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1040 Keyboard” on page 94 v “1050 Palm rest or palm rest with fingerprint reader” on page 97 Table 19.

  • Page 29

    www.battery-adapter.com 1120 I/O card assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1040 Keyboard” on page 94 v “1050 Palm rest or palm rest with fingerprint reader” on page 97 v “1110 Monaural speaker assembly (for X200, X200s, X201s, and X201si)” on page Table 20.

  • Page 30

    www.battery-adapter.com Table 20. Removal steps of I/O card assembly (continued) Note: The cable is secured with a double-faced adhesive tape. Note: Step a is only for ThinkPad X201. For the other models, skip the step Step Screw (quantity) Color Torque M2 ×...

  • Page 31

    www.battery-adapter.com Table 20. Removal steps of I/O card assembly (continued) Turn the I/O card over, and then disconnect the cable from the flip-lock ZIF connector. Removing and replacing a FRU www.battery-adapter.com...

  • Page 32: Lcd Assembly

    www.battery-adapter.com 1130 LCD assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1040 Keyboard” on page 94 v “1050 Palm rest or palm rest with fingerprint reader” on page 97 v “1070 PCI Express Mini Card for wireless LAN/WiMAX” on page 102 v “1080 PCI Express Mini Card for wireless WAN”...

  • Page 33

    www.battery-adapter.com Table 21. Removal steps of LCD assembly (continued) Step Screw (quantity) Color Torque M2 × 5 mm, wafer-head, nylon-coated (2) Black 0.181 Nm (1.85 kgfcm) Before step 3 , strip off the tapes securing the antenna cables, and release the cables from the cable guides of the frame.

  • Page 34

    www.battery-adapter.com Table 21. Removal steps of LCD assembly (continued) ThinkPad X200, X200s, X200si, X201, X201i, and X201s Hardware Maintenance Manual www.battery-adapter.com...

  • Page 35

    www.battery-adapter.com Table 21. Removal steps of LCD assembly (continued) When installing: 1. Route the antenna cables along the cable guides and secure them with the tapes. As you route the cables, make sure that they are not subjected to any tension.

  • Page 36: Base Cover Assembly And Stereo Speaker Assembly For X201 And X201i

    www.battery-adapter.com 1140 Base cover assembly and stereo speaker assembly for X201 and X201i For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1020 Hard disk drive (HDD) cover, HDD, and HDD rubber rails or solid state drive (SSD) and storage converter”...

  • Page 37

    www.battery-adapter.com Table 22. Removal steps of base cover assembly for ThinkPad X200, X201, and X201i (continued) Step Screw (quantity) Color Torque M2 × 3.5 mm, wafer-head, nylon-coated (1) Black 0.181 Nm (1.85 kgfcm) Note: Step 4a is only for X201 and X201i. Step Screw (quantity) Color...

  • Page 38

    www.battery-adapter.com Table 22. Removal steps of base cover assembly for ThinkPad X200, X201, and X201i (continued) In step 5 and 6 , remove the system board, the DC-in connector, and the fan assembly together from the base cover assembly. When installing: Check the position of the wireless switch a , and firmly fit the system board into the base cover assembly.

  • Page 39: Step Screw (quantity) M2 × 3 Mm, Wafer-head, Nylon-coated

    www.battery-adapter.com Table 23. Removal steps of base cover assembly for ThinkPad X200s, X200si, and X201s ThinkPad X200s, X200si and X201s: Remove the top shielding assembly at first. Step Screw (quantity) Color Torque M2 × 3 mm, wafer-head, nylon-coated (1) Black 0.181 Nm (1.85 kgfcm) Step...

  • Page 40

    www.battery-adapter.com Table 23. Removal steps of base cover assembly for ThinkPad X200s, X200si, and X201s (continued) Step Screw (quantity) Color Torque M2 × 3.5 mm, wafer-head, nylon-coated (4) Silver 0.181 Nm (1.85 kgfcm) M2 × 3 mm, large-head, nylon-coated (1) Silver 0.181 Nm (1.85 kgfcm)

  • Page 41: Removing And Replacing A Fru

    www.battery-adapter.com Applying labels to the base cover: The new base cover FRU is shipped with a kit containing labels of several kinds. When you replace the base cover, you need to apply the following labels: Product label Homologation label Non-mercury label Note: If the computer you are servicing is an LED-backlight LCD model, you need to paste this label so that the notice for mercury is covered.

  • Page 42

    System board with Intel Core 2 Duo mobile processor P8600 (2.4 GHz), non-AMT, non-TPM, 4-MB ROM v To identify the system board originally installed in your computer, go to PEW at the following web site: http://www.lenovo.com/support/site.wss/ document.do?lndocid=LOOK-WARNTY Select Warranty Lookup. Input the machine type and the serial number. Use the system board listed on PEW.

  • Page 43

    www.battery-adapter.com Important notices for handling the system board: When handling the system board, bear the following in mind. v The system board has an accelerometer, which can be broken by applying several thousands of G-forces. Note: Dropping a system board from a height of as little as 6 inches so that it falls flat on a hard bench can subject the accelerometer to as much as 6,000 G’s of shock.

  • Page 44

    www.battery-adapter.com Table 24. Removal steps of system board, DC-in connector, fan, and ExpressCard slot assembly for ThinkPad X200, X201, and X201i Following components soldered on the system board are extremely sensitive. When you service the system board, avoid any kind of rough handling. ThinkPad X200: ™...

  • Page 45

    www.battery-adapter.com Table 24. Removal steps of system board, DC-in connector, fan, and ExpressCard slot assembly for ThinkPad X200, X201, and X201i (continued) ThinkPad X201 and X201i: PCH (Platform Controller Hub) Accelerometer chip for the HDD Active Protection System Bottom Note: The DC-in connector and the fan assembly are attached to the underside of the system board.

  • Page 46

    www.battery-adapter.com Table 24. Removal steps of system board, DC-in connector, fan, and ExpressCard slot assembly for ThinkPad X200, X201, and X201i (continued) Turn the system board over, and then disconnect the DC-in connector and the fan connector from the system board. When installing: Make sure that the DC-in connector and the fan connector are attached to the system board firmly.

  • Page 47

    www.battery-adapter.com Table 24. Removal steps of system board, DC-in connector, fan, and ExpressCard slot assembly for ThinkPad X200, X201, and X201i (continued) When installing: v Before you attach the fan assembly to the computer, apply thermal grease, at an amount of 0.2 grams, on the part marked a as in the following figure. Either too much or too less application of grease can cause a thermal problem due to imperfect contact with a component.

  • Page 48

    www.battery-adapter.com Table 24. Removal steps of system board, DC-in connector, fan, and ExpressCard slot assembly for ThinkPad X200, X201, and X201i (continued) Note: The ExpressCard slot assembly is attached to the system board. Step Screw (quantity) Color Torque M2 × 3.5 mm, flat-head, nylon-coated (1) Silver 0.181 Nm (1.85 kgfcm)

  • Page 49

    www.battery-adapter.com Table 25. Removal steps of system board, DC-in connector, fan, and ExpressCard slot assembly for ThinkPad X200s and X201s ThinkPad X200s: Following components soldered on the system board are extremely sensitive. When you service the system board, avoid any kind of rough handling. ICH (I/O Controller Hub) MCH (Memory Controller Hub) Accelerometer chip for the HDD Active Protection System...

  • Page 50

    www.battery-adapter.com Table 25. Removal steps of system board, DC-in connector, fan, and ExpressCard slot assembly for ThinkPad X200s and X201s (continued) ThinkPad X201s: PCH (Platform Controller Hub) Accelerometer chip for the HDD Active Protection System Bottom ThinkPad X200, X200s, X200si, X201, X201i, and X201s Hardware Maintenance Manual www.battery-adapter.com...

  • Page 51

    www.battery-adapter.com Table 25. Removal steps of system board, DC-in connector, fan, and ExpressCard slot assembly for ThinkPad X200s and X201s (continued) Note: Step 1 in only for ThinkPad X201s. Step Screw (quantity) Color Torque M2 × 3.5 mm, wafer-head, nylon-coated (1) Silver 0.181 Nm (1.85 kgfcm) Note: The DC-in connector and the fan assembly are attached to the underside...

  • Page 52

    www.battery-adapter.com Table 25. Removal steps of system board, DC-in connector, fan, and ExpressCard slot assembly for ThinkPad X200s and X201s (continued) Step Screw (quantity) Color Torque M2 × 3.5 mm, wafer-head, nylon-coated (1) Silver 0.181 Nm (1.85 kgfcm) ThinkPad X200, X200s, X200si, X201, X201i, and X201s Hardware Maintenance Manual www.battery-adapter.com...

  • Page 53

    www.battery-adapter.com Table 25. Removal steps of system board, DC-in connector, fan, and ExpressCard slot assembly for ThinkPad X200s and X201s (continued) When installing: v Before you attach the fan assembly to the computer, apply thermal grease, at an amount of 0.2 grams, on the part marked a as in the following figure. Either too much or too less application of grease can cause a thermal problem due to imperfect contact with a component.

  • Page 54

    www.battery-adapter.com Table 25. Removal steps of system board, DC-in connector, fan, and ExpressCard slot assembly for ThinkPad X200s and X201s (continued) Note: The ExpressCard slot assembly is attached to the system board. For ThinkPad X200s: For ThinkPad X201s: Step Screw (quantity) Color Torque M2 ×...

  • Page 55

    www.battery-adapter.com Table 25. Removal steps of system board, DC-in connector, fan, and ExpressCard slot assembly for ThinkPad X200s and X201s (continued) Turn the system board over, and then remove the ExpressCard slot assembly from the system board. Removing and replacing a FRU www.battery-adapter.com...

  • Page 56: Lcd Front Bezel

    www.battery-adapter.com 2010 LCD front bezel For access, remove this FRU: v “1010 Battery pack” on page 85 Table 26. Removal steps of LCD front bezel for 12.1-in. WXGA LCD model 12.1-in. WXGA LCD model: Step Screw cap Screw (quantity) Color Torque M2.5 ×...

  • Page 57

    www.battery-adapter.com Table 27. Removal steps of LCD front bezel for 12.1-in. WXGA+ LCD model 12.1-in. WXGA+ LCD model: Step Screw cap Screw (quantity) Color Torque M2.5 × 4 mm, wafer-head, Black 0.392 Nm nylon-coated (2) (4 kgfcm) M2.5 × 4 mm, wafer-head, Black 0.392 Nm nylon-coated (5)

  • Page 58

    www.battery-adapter.com Table 27. Removal steps of LCD front bezel for 12.1-in. WXGA+ LCD model (continued) In step 4 and 5 , detach the claws. Then remove the LCD front bezel. When installing: Make sure that all the claws are attached firmly. ThinkPad X200, X200s, X200si, X201, X201i, and X201s Hardware Maintenance Manual www.battery-adapter.com...

  • Page 59: Inverter Card Or Led Board

    www.battery-adapter.com 2020 Inverter card or LED board For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “2010 LCD front bezel” on page 138 Table 28. Removal steps of inverter card or LED board For ThinkPad X200, X200s, and X200si: Step Screw (quantity) Color...

  • Page 60

    www.battery-adapter.com Table 28. Removal steps of inverter card or LED board (continued) For ThinkPad X201, X201i, and X201s: Step Screw (quantity) Color Torque M2 × 3.5 mm, wafer-head, nylon-coated (1) Silver 0.181 Nm (1.85 kgfcm) When installing: Make sure that the connector 2 is attached firmly. ThinkPad X200, X200s, X200si, X201, X201i, and X201s Hardware Maintenance Manual www.battery-adapter.com...

  • Page 61

    www.battery-adapter.com 2030 Bluetooth daughter card (BDC-2.1) For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “2010 LCD front bezel” on page 138 Table 29. Removal steps of Bluetooth daughter card When installing: Make sure that the connector 1 is attached firmly. Removing and replacing a FRU www.battery-adapter.com...

  • Page 62: Integrated Camera

    www.battery-adapter.com 2040 Integrated camera For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “2010 LCD front bezel” on page 138 Table 30. Removal steps of Integrated camera Step Screw (quantity) Color Torque M2 × 3.5 mm, wafer-head, nylon-coated (2) Silver 0.181 Nm (1.85 kgfcm) ThinkPad X200, X200s, X200si, X201, X201i, and X201s Hardware Maintenance Manual...

  • Page 63

    www.battery-adapter.com 2050 LCD panel, LCD brackets, and LCD cable For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1040 Keyboard” on page 94 v “1050 Palm rest or palm rest with fingerprint reader” on page 97 v “1070 PCI Express Mini Card for wireless LAN/WiMAX”...

  • Page 64

    www.battery-adapter.com Table 31. Removal steps of LCD panel, LCD brackets, and LCD cable for 12.1-in. WXGA LCD model (continued) Note: Step 3 is only for models without the integrated camera. For models with the integrated camera, skip step 3 . Step Screw (quantity) Color...

  • Page 65

    www.battery-adapter.com Table 31. Removal steps of LCD panel, LCD brackets, and LCD cable for 12.1-in. WXGA LCD model (continued) Remove the LCD bracket a . Step Screw (quantity) Color Torque M2 × 2 mm, wafer-head, nylon-coated (4) Black 0.181 Nm (1.85 kgfcm) Removing and replacing a FRU www.battery-adapter.com...

  • Page 66

    www.battery-adapter.com Table 31. Removal steps of LCD panel, LCD brackets, and LCD cable for 12.1-in. WXGA LCD model (continued) Turn the LCD panel over, and then remove the LCD cable b from the LCD panel. When installing: Make sure that the LCD cable connector is attached firmly. ThinkPad X200, X200s, X200si, X201, X201i, and X201s Hardware Maintenance Manual www.battery-adapter.com...

  • Page 67

    www.battery-adapter.com Table 32. Removal steps of LCD panel, LCD brackets, and LCD cable for 12.1-in. WXGA+ LCD model 12.1-in. WXGA+ LCD model: Step Screw (quantity) Color Torque M2 x 2 mm, wafer-head, nylon-coated (1) Silver 0.181 Nm (1.85 kgfcm) Removing and replacing a FRU www.battery-adapter.com...

  • Page 68

    www.battery-adapter.com Table 32. Removal steps of LCD panel, LCD brackets, and LCD cable for 12.1-in. WXGA+ LCD model (continued) Turn the LCD panel over, and then remove the LCD cable c from the LCD panel. When installing: Make sure that the LCD cable connector is attached firmly. ThinkPad X200, X200s, X200si, X201, X201i, and X201s Hardware Maintenance Manual www.battery-adapter.com...

  • Page 69: Hinges And Hinge Brackets

    www.battery-adapter.com 2060 Hinges and hinge brackets For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1040 Keyboard” on page 94 v “1050 Palm rest or palm rest with fingerprint reader” on page 97 v “1070 PCI Express Mini Card for wireless LAN/WiMAX” on page 102 v “1080 PCI Express Mini Card for wireless WAN”...

  • Page 70

    www.battery-adapter.com Table 34. Removal steps of hinges and hinge brackets for 12.1-in. WXGA+ LCD model 12.1-in. WXGA+ LCD model: In step 1 , release the antenna cables from the cable guides. ThinkPad X200, X200s, X200si, X201, X201i, and X201s Hardware Maintenance Manual www.battery-adapter.com...

Comments to this Manuals

Symbols: 0
Latest comments: