Troubleshooting Guide; To Reset Unit; Power; Operation - Panasonic SC-BT205 Operating Instructions Manual

Troubleshooting guide

Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the solutions indicated in the chart
do not solve the problem, consult your dealer for instructions.
The following do not indicate a problem with this unit:
≥Regular disc rotating sounds.
≥Image disturbance during search.
To reset this unit
To restore the unit if it freezes
due to one of the safety
devices being activated
To return all settings other than
some settings to the factory
preset
To return to the factory preset
(No setting)

Power

No power.
The unit switches to standby mode.
Power of this unit is turned off
when the input for the TV is
changed.

Operation

The remote control doesn't
work properly.
The unit is on but cannot be
operated.
Play fails to start even when
[1PLAY] is pressed.
Play starts but then stops
immediately.
Cannot eject disc.
Startup is slow.
It takes time before play starts.
Played back image is distorted
or does not playback correctly.
([AVCHD])
Cannot set "On" in "24p
Output".
RQT9516
48
48
≥Press and hold [Í/I] on the main unit for 3 seconds. (The settings remain unchanged.)
≥Select "Yes" in "Default Settings" in the Setup menu.
This returns all values in the Setup menu and the on-screen menu, except for "Remote
Control", "On-Screen Language", "IP Address / DNS Settings", "Proxy Server Settings",
"DVD-Video Ratings", "BD-Video Ratings" and "Network Service" to the default settings.
≥Reset the unit as follows:
1 Press [Í/I] on the unit to turn off the unit.
2 Press and hold [5/9] and press [Í/I] and [< OPEN/CLOSE] on the unit at the same
time for more than 5 seconds until "PLEASE WAIT" is displayed on the unit.
3 The power is turned on and then turned off automatically.
≥Insert the AC mains lead securely into a household mains socket.
≥When the time set for the sleep timer has passed, the power will be turned off.
≥One of the unit's safety devices is activated. Press [Í/I] on the main unit to turn the unit on.
≥If connected with an HDAVI Control 4 compatible TV (VIERA) with the "Intelligent Auto
Standby" setting activated on the TV, when switching the TV input, the unit will be
automatically turned to standby if the TV audio is not output from the unit's speakers. For
details please read the operating instructions of the TV.
≥The remote control and main unit are using different codes.
Change the code on the remote control.
Press and hold [OK] and the indicated number button at the
same time for more than 5 seconds.
≥The batteries are depleted. Replace them with new ones.
≥It may be necessary to set the code of the remote control again after changing the batteries
for remote control.
≥You are not pointing the remote control at the main unit's remote control signal sensor during
operation.
≥Coloured glass may obstruct the signal reception/transmission.
≥Don't place the signal sensor in direct sunlight or in areas that may be subject to sunlight exposure.
≥Confirm the correct drive is selected.
≥Some operations may be prohibited by the disc.
≥The unit is hot ("U59" appears on the display). Wait for "U59" to disappear.
≥One of the unit's safety devices may have been activated.
Reset the unit as follows:
1 Press [Í/I] on the main unit to switch the unit to standby.
If the unit doesn't switch to standby, press and hold [Í/I] on the main unit for about 3
seconds. The unit is forcibly switched to standby.
Alternatively, disconnect the AC mains lead, wait one minute, then reconnect it.
2 Press [Í/I] on the main unit to switch it on. If the unit still cannot be operated, consult the
dealer.
≥Condensation has formed. Wait 1 to 2 hours for it to evaporate.
≥Insert the disc correctly with the label facing up.
≥The disc is dirty.
≥You tried to play a blank disc or unplayable media on this unit.
≥[DivX] If playing DivX VOD content, refer to the homepage where you purchased it.
≥The producers of the disc can control how discs are played. So you may not always be able
to control play as described in these operating instructions. Read the disc's instructions
carefully.
≥The unit may have a problem. While the unit is off, press and hold [5/9] and [< OPEN/
CLOSE] on the main unit at the same time for about 5 seconds. Remove the disc and consult
the dealer.
≥Startup takes time in the following situations.
– Immediately after a power failure or the AC mains lead is connected.
– When the unit is connected with an HDMI cable.
≥High definition video (transfer rate of 18 Mbps or faster) cannot be played back correctly if it
was recorded on a DVD compatible to double speed or slower.
≥Only when the unit is connected to the HDMI terminal of a TV supporting 24p you can select
"On".
Page
—
40
—
13
20
—
29
51
5
5, 51
5
—
—
16
—
53
—
—
18
3
44, 45
22
—
—
—
—
39