Table of Contents
Advertisement
8 Troubleshooting Guide
8.1. About Operation of Set
General operation
To return to the factory defaults.
Select "Restore" in "Default" in the Setup
menu. (
17)
To return all settings to the factory preset.
Reset the unit as follows:
Turn the unit on.
Press [ ] to open the disc tray.
Press and hold [ ] and [ / ] on the main
unit at the same time for more than
5 seconds.
You have forgotten your ratings password.
You want to cancel the ratings level.
The ratings level returns to the factory defaults.
Restore the default settings following the
steps described in "To return all settings to
the factory preset.". (
This unit does not recognize the USB
connection correctly.
Disconnect and re-connect the USB cable. If
it still does not recognize the connection, turn
this unit off and on again.
USB devices may not be recognized by this
unit when connected using the following :
a USB hub
a USB extension cable
If you connect USB HDD to this unit, use the
USB cable that is supplied with the HDD.
Picture
The images from this unit do not appear on
the TV.
Picture is distorted.
Jittering occurs.
The "Resolution" setting is incorrect or the
"TV System" setting of the unit and that of the
TV do not match.
Restore the default settings following the
steps described in "To return all settings to
the factory preset.". (
PAL discs cannot be correctly viewed on an
NTSC TV.
If irregular colouring occurs on your TV, turn
the TV off for about 30 minutes.
If it persists, move the speakers further away
from the TV.
Sound
No sound.
Low volume.
Distorted sound.
Cannot hear the desired audio type.
Depending on the connected equipment, the
sound may be distorted if this unit is
connected with an HDMI cable.
The multi-channel audio from a device
connected to the TV is not output in it's
original multi-channel form.
If the device has an optical audio output
terminal, connect the device to this unit's
DIGITAL AUDIO IN terminal. (
No sound from the TV.
If there is no sound from the equipment
connected to this unit's DIGITAL AUDIO IN
terminal, please make sure that the optical
audio output of the equipment is set to PCM.
above)
left)
7)
16
Playback
Disc cannot be played.
The disc is dirty. (
3)
Alternative subtitles cannot be selected.
You may not be able to use the Option menu
to change the subtitles on some discs. Use
the disc's menus to make changes.
Bluetooth
®
Pairing cannot be done.
Check the Bluetooth
®
device condition.
The device cannot be connected.
Try pairing the device again.
This system might be connected to a different
device. Disconnect the other device and try
pairing the device again.
The device is connected but audio cannot be
heard through this system.
For some built-in Bluetooth
®
have to set the audio output to "Panasonic
XH" manually. Read the operating instructions
for the device for details.
The sound is interrupted.
The communication range is 10 m. Bring the
Bluetooth
device closer to the main unit.
®
Other devices that use the 2.4 GHz frequency
band (wireless router, microwaves, cordless
phones, etc.) are interfering. Bring the
Bluetooth
device closer to the main unit and
®
distance it from the other devices.
Radio
Distorted sound or noise is heard.
Adjust the position of the antenna.
A beat sound is heard.
Try to keep a certain amount of distance
between the antenna and the TV.
Messages on the screen
Error Disc
You inserted an incompatible disc.
The disc may be upside down.
This operation is not available.
Some operations are unsupported by the unit.
Unit's display list
This list only contains displays that are difficult to read.
Display
Reading
Display
OFF
LOAD
STOP
DISC
AUX
ERASE
DONE
ERR (Error)
BLUETOOTH
devices, you
Reading
OPEN
MUTE
SETUP
USB
OPT (Optical)
UPD (Update)
No DISC,
No PLAY,
No READ,
UNSUPPORT
Advertisement
Table of Contents
