Using The Cr224 Remote Control - Arcam CD73 Handbook

Using the CR224 remote control

You can program a selection of up to 24 tracks
from a disc to play in any order. Select a track by
using the and buttons, then press
program the track into memory ('PROGRAM' appears
on the display to indicate that you have started
programming a sequence). Repeat these steps to
program the remaining tracks in your selection.
Alternatively, press once and enter your track
PROG
selection using the 0–9 keypad.
The display shows the track numbers programmed,
the total length of the programmed sequence and
the number of tracks programmed (shown by a
number below the word 'STEP').
Each time you enter a track the number below 'STEP'
increments by one and flashes until you press
to confirm. If you fail to press
seconds the display stops flashing and you will have
Press to play the program. Press
the entire sequence from the start. Press
again to exit the program facility: the display flashes
'CONTINUE' and shows '0'.
Skip and Search Track
Skip track backwards and forwards; search
backwards and forwards (see page 5)
Press once to display the remaining time of the
TIME
currently playing track. Press again to display the
time remaining on the disc. Press a third time to turn
Press again and the display reverts to its
TIME
original setting, showing the time elapsed for the
For CDs with text, pressing
TIME
is loaded but not playing displays the artist's name.
Pressing a second time displays the total
TIME
number of tracks and the total playing time.
Turns the display on or off. Turning the display off
generally produces a slight improvement in sound
Opens and closes the CD tray.
These operate in the same way as the source
selector on the front panel of an Arcam integrated
CD73
6
PROG (Program)
to
PROG
PROG
within about five
PROG
to reselect the track.
again to replay
PROG
TIME
the text display on.
current track.
once while the disc
DISP (Display)
quality.
OPEN
Source selection
amplifier.
0–9 keypad
This allows direct access to individual tracks on
the disc. To select a track, press the corresponding
keypad button. For tracks greater than 9, enter the
digits in sequence. For example, to play track 15,
press and hold until the number on the display
1
moves to the left, then press
Playback control
Play, Stop and Pause (see page 5).
REPEAT
To repeat the entire CD or a pre-programmed
selection of tracks press
REPEAT
lights on the display. To repeat a particular track,
select that track and then press
that 'REPEAT 1' is shown on the display. If you now
select a different track, that track is repeated
instead.
To cancel the repeat function press
time.
A–B
This button enables you to repeat any section of
music within a track. Whilst the disc is playing, press
the button at the start of the section you wish
A–B
to repeat. 'REPEAT' is shown on the display and the
letter 'A–' flashes. Press the button a second time
when you reach the end of the section you wish to
repeat. The 'A–B' letters stop flashing and remain
lit. This section will repeat until you press
. The forward search button (
within the selected loop.
SHUFFLE
Press once to shuffle play CD tracks (i.e. play them
in a random order). Press again to cancel shuffle
play.
MUTE
Stops sound to the speaker outputs of certain Arcam
amplifiers.
VOL (Volume) +/–
Adjusts the volume on Arcam remote-controllable
amplifiers.
Note that the volume (+/–) controls and
button have no effect on the audio output level of the
CD players.
NOTE: Remember to install the two AAA batteries
supplied before trying to use your remote control.
Do not place anything in front of the display area
on the CD player (where the IR receiver is located),
or the remote control may not work.
.
5
once: 'REPEAT'
twice so
REPEAT
a third
REPEAT
or or
) moves forward
MUTE