Advertisement
Table of Contents
- 1 Read First
- 2 Speaker Placement
- 3 Mounting Options
- 4 Wall Mounting
- 5 Speaker Connections
- 6 Connection Tips
- 7 Dolby* Digital or Dts (or Other Digital Surround Mode) Connection
- 8 Dolby Pro Logic* (Non-Digital) - Line Level
- 9 Dolby Pro Logic (Non-Digital) - Speaker Level
- 10 Operation
- 11 Troubleshooting
- 12 Specifications
- Download this manual
Advertisement
Table of Contents
Related Manuals for JBL SCS200.5/230
Summary of Contents for JBL SCS200.5/230
- Page 1 The SCS200.6 system is shown here. SURROUND CINEMA SPEAKERS SCS200.5/230 and SCS200.6/230 OWNER’S GUIDE ®...
-
Page 2: Read First
READ FIRST! 1. Unpacking: Check the product carefully. If it has been damaged in transit, report the damage immedi- ately by calling your dealer and/or the shipping company that delivered it. 2. Connections: Whenever changing, connecting or disconnecting signal or power cables etc., always turn off all equipment. - Page 3 antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and require- ments for the grounding electrode. See Figure A. 18. An outside antenna system should not be located in the vicinity of over- head power lines or other electric light or power circuits, or where it can fall into such power lines or cir- cuits.
- Page 4 THANK YOU FOR CHOOSING JBL For more than 50 years, JBL has been involved in every aspect of music and film recording and reproduction, from live performances to the recordings you play in your home, car or office. We’re confident that the JBL...
-
Page 5: Speaker Placement
SPEAKER PLACEMENT FRONT SPEAKERS SURROUND SPEAKERS † Alternate placement for surround speakers in SCS200.5 system only. The front speakers should be placed the same distance from each other as they are from the listening position. They should be placed at about the same height from the floor as the listeners’... -
Page 6: Mounting Options
MOUNTING OPTIONS SATELLITES AND SURROUNDS On shelves. ATTACHING THE SHELF STAND TO THE SPEAKER Prepare the speaker wire as described on page 8. Thread the two conductors through the two holes in the stand bracket. Make sure to pre- serve the proper polarity (+ and –... -
Page 7: Wall Mounting
JBL disclaims any liability for the selection of mounting hardware and/or bracket installation. Be sure to follow these bracket assembly and installation instructions carefully. -
Page 8: Speaker Connections
Speakers and elec- tronics terminals have corre- sponding (+) and (–) termi- nals. Most manufacturers of speakers and electronics, including JBL, use red to denote the (+) terminal and black to denote the (–) terminal. the holes in the outer edge of ™... -
Page 9: Dolby* Digital Or Dts (Or Other Digital Surround Mode) Connection
DOLBY* DIGITAL OR DTS (OR OTHER DIGITAL SURROUND MODE) CONNECTION RECEIVER SUBWOOFER LINE LFE OUT LEVEL Use this installation method for Dolby* Digital, DTS ® other digital surround processors: Use the line-level input jack marked “LFE” for the Low- Frequency Effects channel. Connect this jack to the LFE DOLBY PRO LOGIC* (NON-DIGITAL) –... -
Page 10: Dolby Pro Logic (Non-Digital) - Speaker Level
DOLBY PRO LOGIC (NON-DIGITAL) – SPEAKER LEVEL Use this installation method for Dolby Pro Logic applica- tions (not Dolby Digital, DTS or other digital processing), where the receiver/proces- sor does not have a sub- woofer output, or a volume- controlled preamp (line-) level output: Connect your receiver or amplifier’s front left and right... -
Page 11: Operation
OPERATION Move the Master Power å switch (marked “Power” to the “•” (On) position to use the SUB200 subwoofer. If you will be away from home for an extended period of time, or if the subwoofer will not be used, switch the å... -
Page 12: Troubleshooting
If the problem has fol- lowed the speaker, consult your dealer for further assistance or, if that is not possible, visit www.jbl.com. If there is no sound from the center speaker: • Check all wires and con- nections between receiver/ amplifier and speaker. - Page 13 If there is no sound from the surround speakers: • Check all wires and con- nections between receiver/ amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punc- tured, or touching each other.
-
Page 14: Specifications
SURROUND CINEMA SPEAKERS MODEL: SCS200.5/230 and SCS200.6/230 Bring the thrill of live performance and movie sound DESIGN GOAL: to the home environment by calling on JBL’s professional engineering leadership. Titanium-laminate-dome tweeter, SATELLITE TYPE: sealed enclosure Bass-reflex enclosure SUBWOOFER TYPE: FreeFlow ™...