REPAIRS AND / OR SERVICE TO THIS TOOL MUST ONLY BE DONE BY AN AUTHORIZED AND CERTIFIED DEALER. For the nearest authorized and certified dealer, call Stanley Hydraulic Tools at the number listed on the back of this manual and ask for a Customer Service Representative.
Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULATIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel. 4 ► CS05/CS06 User Manual...
The model CS05/CS06 Hydraulic Chain Saw will provide bestos, silica or lead. Inhalation of dust containing safe and dependable service if operated in accordance these or other hazardous substances could result with the instructions given in this manual.
Page 6
– Only use replacement bars and chains specified the tension on the limb is released. by Stanley Hydraulic Tools. Chains must meet the requirements of ANSI B175.1 for low kick- • Keep the handles dry, clean and free of oil.
345.0 to 362.0 13–02 4.02 15–00 4.58 16–03 4.96 500.0 to 550.0 19–00 5.80 21–09 6.63 23–06 7.17 765.0 to 800.0 27–04 8.34 31–03 9.53 33–10 10.32 Exceeds phase-to-ground; elevation factor per 29 CFR 1910.269. CS05/CS06 User Manual ◄ 7...
Page 8
Aerial devices and attached equipment (such as chip- pers) contacting energized electrical conductors shall be considered energized. Contact shall be avoided, except where emergency rescue procedures are being carried out. Emergency rescue should be performed in accor- dance with 4.3. 8 ► CS05/CS06 User Manual...
OR OTHER TOOL FAILURE. CONTACT AT A LEAK OR BURST CAN CAUSE OIL INJECTION INTO THE BODY. FAILURE TO OBSERVE THESE PRECAUTIONS CAN RESULT IN SERIOUS PERSONAL INJURY. 03782 GPM Decal – CS05 Model 03786 13907 GPM Decal – CS06 Model (Not Shown) Kickback Warning Decal...
HOSE SAFETY TAGS To help ensure your safety, the following DANGER tags are attached to all hose purchased from Stanley Hydraulic Tools. DO NOT REMOVE THESE TAGS.
2000 psi 2000 psi 2000 psi (at the power supply outlet) (172 bar) (138 bar) (138 bar) (138 bar) (138 bar) NOTE: These are general hydraulic system requirements. See tool specification page for tool specific requirements 12 ► CS05/CS06 User Manual...
4-6 gpm/15-23 lpm at 1500-2000 psi/105- beyond the point of initial resistance. 140 bar for the CS05 or a flow of 7-9 gpm/26-34 lpm at 1000-2000 psi/70-140 bar for the CS06. OPERATING PROCEDURES 2.
Make a diagonal cut down to meet the hori zontal cut the guide bar will not get pinched. and remove the wood from the notch. 14 ► CS05/CS06 User Manual...
4. Cut from the bottom. Make a boring cut if the log is close to the ground. 5. Finish with a bottom cut. Figure 4. Crosscutting Logs Larger than Bar Length With Pressure on Top CS05/CS06 User Manual ◄ 15...
3. Pull the saw towards you and cut from the top. 4. Cut from the bottom. Make a boring cut if the log is close to the ground. 5. Finish with a top cut. Figure 6. Crosscutting Thick Logs with Pressure on Bottom 16 ► CS05/CS06 User Manual...
Never force a dull chain to cut. 4. Clean out the bar groove and keep the oil hole open. Turn the bar over to equalize wear on the rails. 5. Always install a new sprocket with a new chain. CS05/CS06 User Manual ◄ 17...
This can cause damage to internal seals. • Always replace hoses, couplings and other parts with replacement parts recommended by Stanley Hydraulic Tools. Supply hoses must have a mini- mum working pressure rating of 2500 psi/172 bar. 18 ► CS05/CS06 User Manual...
Tool does not run. Power unit not functioning. Check power unit for proper flow and pressure (4 gpm/15 lpm at 1500 psi/104 bar minimum for the CS05 and 7 gpm/26 lpm at 1000 psi/70 bar for the CS06). Coupler or hoses blocked.
CIRCUIT TYPE D DECAL (CE ONLY) 07639 SAW BAR 20 IN. 10535 ON/OFF VALVE SPOOL 08348 SAW CHAIN – 12 IN. 07626 O-RING 07641 SAW CHAIN – 15 IN. 07609 SPRING WASHER 07642 SAW CHAIN – 20 IN. 22 ► CS05/CS06 User Manual...
Page 23
GPM STICKER (7–9 GPM) 03782 GPM STICKER (4–6 GPM) 05144 BAR & CHAIN GUARD 00767 GREASE FITTING U/W MODEL ONLY 00936 ADAPTER (NOT SHOWN) 26414 LOCK OUT KIT, SHIPPED INSTALLED (NOT SHOWN) 03971 COUPLER SET 07830 SEAL KIT CS05/CS06 User Manual ◄ 23...
Page 24
Stanley Hydraulic Tools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www.stanleyhydraulic.com IMPORTANT To fill out a Product Warranty Recording form, and for information on your warranty, visit Stanleyhydraulic.com and select the Warranty tab.