Configuring Time And Date Settings Manually - Casio 3311 Operation Manual

❚ Elapsed Time Measurement
Start Stop
Pressing the A button while timing is stopped resets the stopwatch to all zeros.
Cumulative Time Measurement
Pressing the D button to restart the stopwatch without resetting it to all zeros causes the elapsed time measurement to resume from
where it was last stopped.
❚ Split Time Measurement
Start Record Split
Pressing the A button while timing is being performed displays the split time screen, but timing continues internally.
• Changing to another mode while a split time is displayed clears the split time operation.
❚ 1st and 2nd Place Finishers
Start 1st Finish
(Displays time of 1st finisher.)
Pressing the D button while the split time screen is on the display stops elapsed time measurement, and leaves the split time screen on
the display. Press the A button to exit the split time screen and display the elapsed time when the measurement was stopped.
Split Time Screen
The split time screen cycles alternately cycle through
the split indicator, a minute/second screen, and a
1/100 second screen.
❚ To configure digital settings
1.
Timekeeping Mode
In the Timekeeping Mode
hold down the A A A A A button
for about two seconds.
• This will display the
transmitter selection mode
setting screen and cause the
second hand to move to the
12 o'clock position.
(Enters/Exits Setting Screen) (Scrolls Back)
(Changes Selection) (Scrolls Forward)
2.
(Changes Setting Group)
Press the A A A A A button to
advance to the next group
of settings.
• This causes the 12/24-hour
timekeeping setting to flash.
Example: 12H (12-hour timekeeping)
Operation Guide 3311/3356
Reset
Clear Split Stop
2nd finish Displays time of 2nd finisher.
Split Indicator Minutes Seconds
3.
Press the C C C C C button so the
setting you want to
change is flashing on the
display.
• Use the C button to cycle
(Selects Setting)
through the settings shown
below. Each press of the C
button causes the next setting
to flash.
12/24-hour
Second Hour Minute
Timekeeping
Power Saving Language Day
4.
While the 12/24-hour
timekeeping setting is
flashing, press the D D D D D
button to select the
setting you want.
• Pressing the D button
toggles the timekeeping
format between 12-hour (12H)
and 24-hour (24H).

Configuring Time and Date Settings Manually

If you are planning to manually adjust both the digital and analog settings, be sure to adjust the digital setting first.
Time and Date Settings
Timekeeping Mode
Reset
(Hold down about two seconds.)
Transmitter Selection
Mode
Reset Auto Receive
12/24-hour
timekeeping
1/100 Second
Power
Saving
• While the setting screen (the one with a flashing setting) is on the
display, use the C and A buttons to move the flashing between
settings.
5.
To restart the seconds
count to 00, press the D
button.
• While the seconds are
selected, press the D button
to reset them to 00 in
accordance with the time
signal on the radio, TV, etc.
• Pressing the D button while the seconds count is in the range
of 30 to 59 resets it to 00 and also adds 1 to the minutes.
Pressing the D button in the range of 00 to 29 resets the
Year
seconds count without changing the minutes.
• Pressing the B button while the seconds count is flashing
changes the display illumination duration. See "To specify
display illumination duration" for more information.
Month
6.
While the hour, minutes,
year, month, or day setting
is flashing, use the D D (+) D D D
and B B B B B (–) buttons to
change the setting.
• Holding down either button
changes the setting at high
(Toggles) speed.
• When setting the hour, make sure you specify AM (no
indicator) or PM (P) correctly, or that you specify the correct
24-hour time.
• You can set a date in the range of January 1, 2000 to
December 31, 2099.
• The day of the week is set automatically in accordance with
the date you set.
• The watch automatically makes adjustments for leap years
and month lengths.
• Displays Setting Screen
• Changes Setting Group
• Exits Setting Screen
Home City Code
(Selects Setting)
You can select either Japanese (kanji) or English for the day of the
Summer Time
week indicator.
• For more information, see "To configure digital settings".
Day of the Week Indicators
Sunday: SU/
Seconds Hour Minute Year
Wednesday: WE/
Saturday: SA/
Language Day Month
See "Signal Reception Settings" for information about
calibration signal, Home City, summer time, and auto
receive settings.
7.
While the day of the week
D D D D setting is flashing, press
the D D D D button to toggle it D
between Japanese (kanji)
and English.
(Zero Reset)
8.
While the Power Saving
setting is flashing, press
the D D D D button to toggle it D
on (ON) or off (OF).
(Back)
Use the C button to select each of the settings and the D
and B buttons to change them.
9.
(Forward) When all of the settings
are the way you want,
press the A
• This exits the setting screen.
• The display also will exit the
setting screen automatically if
you do not perform any
operation for about two or
three minutes.
Monday: MO/ Tuesday: TU/
Thursday: TH/ Friday: FR/
Japanese (Kanji)
(Toggles)
(Toggles)
A button. A A A
8