Advertisement
To toggle the Home City time between standard time and daylight saving time
1.
Perform the step 1 under "To configure Home City settings".
•
Each time you select a city code, the
z Hour Hand and c Minute Hand move to the current time for that
city code. Do not perform the next operation until these hands stop moving.
•
The short end of the
v Day of the Week Hand will indicate whether the currently selected city code is
configured for standard time (STD) or daylight saving/summer time (DST).
B to toggle the time for the city code of the currently selected Home City between STD (standard
2.
Press
time)/DST (daylight saving time).
•
Note that you cannot switch between
STD (standard time)/DST (daylight saving time) while UTC is
selected as your Home City.
3.
After the setting is the way you want, press
Note
•
After you specify a city code, the watch will use UTC* offsets to calculate the World Time based on the
current time in your Home City.
*
Coordinated Universal Time, the world-wide scientific standard of timekeeping. The reference point for
UTC is Greenwich, England.
•
Selecting some city codes automatically makes it possible for the watch to receive the time calibration
signal for the corresponding area. See "Radio Controlled Atomic Timekeeping" for details.
Configuring Current Time and Date Settings Manually
You can configure current time and date settings manually when the watch is unable to receive a time
calibration signal.
To change the current time setting manually
1.
In the regular timekeeping mode, keep
the x Second Hand goes through the following sequence.
•
Moves to
YES (or Y for some models) or NO (N) to indicate the last signal
reception result, then to READY (R), and then to the city code of the currently
selected Home City.
•
The short end of the
currently selected city code is configured for standard time (STD) or daylight
saving/summer time (DST).
2.
Change the Home City and daylight saving time (DST) settings, if you want.
•
For details about these settings, see steps 2 and 3 under "To configure Home
City settings".
•
In the following steps, each press of
below.
Home city/DST
3.
Press
C.
•
The
v Day of the Week Hand will move to Su. This is the time setting mode.
•
The
x Second Hand indicates whether the current time is a.m. (A) or p.m. (P).
4.
Use
D (+) and B (–) to change the time (hour and minute) setting.
•
Each press of either button will move the hands (
•
Holding down
D or B will start high-speed z Hour Hand and c Minute Hand movement in the
applicable direction. To stop high-speed hand movement, press any button.
•
When setting the time, make sure that the
for the time you are setting.
•
If you want to change the date setting at this time, press
step 3 under "To change the current date setting manually".
5.
After the time setting is the way you want, press
•
This will cause the
x Second Hand to move automatically to 12 o'clock and resume movement from
there.
To change the current date setting manually
1.
In the regular timekeeping mode, keep
00
seconds) as the x Second Hand goes through the following sequence.
10
•
Moves to
signal reception result, then to READY (R), and then to the city code of
the currently selected Home City.
20
2.
Press
C twice.
•
The
x Second Hand will move to the tens digit of the current year
90
30
setting. This is the year setting mode.
80
40
•
The year can be set in the range of 2000 to 2099.
3.
Press
D to move the x Second Hand clockwise until it is pointing at the
year tens digit you want to select.
70
50
60
Setting the year (tens digit)
0
4.
After you select the year tens digit, press
•
The
x Second Hand will move to the ones digit of the current year.
1
5.
Press
D to move the x Second Hand clockwise until it is pointing at the
year ones digit you want to select.
2
6.
After you select the year ones digit, press
•
The
x Second Hand will move to the currently selected month. This is
9
3
the month setting mode.
8
4
•
7
5
6
Setting the year (ones digit)
Operation Guide 5076 (OC)
A to return to regular timekeeping.
A depressed (for about five seconds) as
v Day of the Week Hand will indicate whether the
C cycles between settings as shown
Hour/Minute
Day
z Hour Hand and c Minute Hand) one minute.
x Second Hand is in the correct A (a.m.) or P (p.m.) position
C and perform the procedure starting from
A to return to regular timekeeping.
A depressed (for about five
YES (or Y for some models) or NO (N) to indicate the last
C.
C.
Dec
•
•
Nov
Oct
Sep
Aug
Jul
Jun
Setting the month
Checking the Current Time in a Different Time Zone
You can use World Time to view the current time in one of 29 time zones around the globe. The currently
selected city is called the "World Time City".
Year (tens digit)
Year (ones digit)
Changing the World Time City
Month
Starting from the regular timekeeping mode, press C to enter the World Time setting mode. You can use the
World Time setting mode to select a World Time City, and to specify daylight saving/summer time (DST) or
standard time for the selected city.
To view the time in another time zone
C to move the v Day of the Week Hand to STD or DST.
1.
Use
•
This indicates the World Time setting mode.
2.
Use
D to move the x Second Hand to the city code you want to select as the World Time City.
•
The
n World Time Hour Hand and m World Time Minute Hand will move to the current time in the time
zone of the current city code. At this time, the
z Hour Hand and c Minute Hand will continue to indicate the current time in the Home City.
•
For full information on city codes, see the "City Code Table".
•
If you think that the time indicated for the selected time zone is not correct, it probably means that there
is something wrong with your Home City settings. Use the procedure under "To configure Home City
settings" to correct the Home City settings.
3.
Press
C to return to regular timekeeping.
To specify standard time or daylight saving time (DST) for a city
Hold down
A for two
seconds.
Swapping your Home City and World Time City
You can use the procedure below to swap your Home City and World Time City. This capability can come in
handy when you frequently travel between two locations in different time zones.
The following example shows what happens when the Home City and World Time City are swapped while the
Home City originally is TOKYO (TYO) and the World Time City is NEW YORK (NYC).
Before swapping
After swapping
7.
Use
D to move the x Second Hand to the month setting you want.
Jan
8.
After the month setting is the way you want, press
•
The x Second Hand will move to 12 o'clock, and the watch will enter
Feb
the day setting mode.
9.
Use
D (+) and B (–) to change the b Day setting.
Mar
•
If you want to change the time setting at this time, press
Apr
then perform the procedure starting from step 3 under "To change
the current time setting manually".
10.
After the settings are the way you want, press
May
timekeeping.
•
This will cause the
x Second Hand to move automatically to
12 o'clock and resume movement from there.
•
The day of the week indicated by the
changes automatically in accordance with the date (year, month,
and day).
Note
•
The watch's built-in full automatic calendar makes allowances for
different month lengths and leap years. Once you set the date,
there should be no reason to change it except after you have the
watch's rechargeable battery replaced or after power drops to
Level 3.
Hand Functions
n World Time Hour Hand:
Indicates the current time in the World Time City in 24-hour format.
m World Time Minute Hand
Hand Functions
x Second Hand: Indicates the currently selected World Time City.
v Day of the Week Hand:
The short end of the hand indicates whether the time for the currently selected
World Time City is standard time (STD) or daylight saving/summer time (DST).
n World Time Hour Hand:
Indicates the current time in the World Time City in 24-hour format.
m World Time Minute Hand
1.
In the regular timekeeping mode, press
mode.
2.
Use
D to select the city code whose setting you want to change.
•
Wait until the
n World Time Hour Hand and m World Time Minute Hand
complete their move to the time in the currently selected World Time City.
You will not be able to perform step 3 of this procedure until the hands stop
moving.
3.
Hold down
A for about two seconds until the short end of the v Day of the
Week Hand toggles to STD (standard time) or DST (daylight saving/summer
time).
•
Note that you cannot switch between
saving/summer time) while UTC is selected as the World Time City.
•
Note that the
STD (standard time)/DST (daylight saving/summer time)
setting affects only the currently selected time zone. Other time zones are
not affected.
4.
Press
C to return to regular timekeeping.
Home City
TOKYO
10:08 p.m.
(Standard time)
(Daylight saving time)
NEW YORK
9:08 a.m.
(Daylight saving time)
C.
C and
A to return to regular
v Day of the Week Hand
C to enter the World Time setting
STD (standard time)/DST (daylight
World Time City
NEW YORK
9:08 a.m.
TOKYO
10:08 p.m.
(Standard time)
3
Advertisement
