Alto PA MONITOR PROCESSOR User Manual page 6

3. CONTROL ELEMENTS
3. CONTROL ELEMENTS
Rear Panel
AC INPUT
95-120V /210-240V 60-50Hz
Rated Power Consumption 8W
FUSE:
210-240V: T200mAL 250VAC
95-120V: T315mA 250VAC
REPLACE FUSE WITH CORRECT
TYPE ONLY
Apparaten skall anslutas till
jordat uttag nar den ansluts
till ett natverk
17
17 AC Inlet and Fuse Holder
Standard IEC receptacle. Connect your
supplied AC power cord. Before powering up your
first time, make certain the stated power requirement of the unit matches the
voltage supplied by the AC socket.
If the fuse blows, replaced with a fuse of the correct type only.
18 Input Connectors
The input connectors are supplied with XLR and 1/4" TRS jack, it is used to
input the signal.
19 Output Connectors
The output connectors are supplied with XLR and 1/4" TRS jack, it is used to
output the signal.
3. CONTROL ELEMENTS
4. APPLICATION IN MONITOR SYSTEM
AC INPUT
95-120V /210-240V 60-50Hz
Rated Power Consumption 8W
FUSE:
210-240V: T200mAL 250VAC
95-120V: T315mA 250VAC
REPLACE FUSE WITH CORRECT
TYPE ONLY
Apparaten skall anslutas till
jordat uttag nar den ansluts
till ett natverk
Output
Monitor AMP Input
D1
500W 2
SIG CLIP PROT SIG CLIP PROT
20 20
18 22 18 22
16 24 16 24
12 26 12 26
6 28 6 28
CH1 30 (dB) CH2 30 (dB)
Monitor AMP Output
Monitor Speaker
4
TIP/PIN 2 TIP/PIN 2
RING/PIN 3 RING/PIN 3
SLEEVE/PIN 1 SLEEVE/PIN 1
OUTPUT INPUT
INPUT
19 18
LTO MONITOR to the AC with the
LTO MONITOR
TIP/PIN 2 TIP/PIN 2
RING/PIN 3 RING/PIN 3
SLEEVE/PIN 1 SLEEVE/PIN 1
OUTPUT INPUT INPUT
Input
AUX Send
MIC level signal
Ok, you have got to this point and you are now in the position to operate your
LTO MONITOR
following section to be the real master of your own unit. Not paying attention
enough to the input signal level, to the routing of the signal and the assignment
of the signal will result in unwanted distortion, a corrupted signal or no sound
at all. So you should follow these procedures for every single channel:
5.1 Mains Connection
Please ensure that the
plugging the power cord into the wall outlet, use the same fuse as marked on
for the
the fuse holder at the AC power connection. The mains connection of the
MONITOR
It meets all of the international safety certification requirements.
5.2 Audio Connection
The
can be interfaced in several ways to support a variety of applications without
any signal loss. The
connecting to the mixing console's main inserts, or on an entire mix "in-line" between
a mixing console's outputs and a power amplifier. The defective wiring may degrade
the performance of
cables only. Please follow the guide below to interface
experiencing any noise or signal loss.
3. CONTROL ELEMENTS 5. INSTALLATION AND CONNECTION
successfully. However, we advise you to read carefully the
LTO MONITOR is set to the correct supply voltage before
is made by using the enclosed mains cord and a standard IEC receptacle.
LTO MONITOR presents with balanced XLR&1/4" TRS
LTO MONITOR can be used on a single instrument by
LTO MONITOR , so please use good quality screened audio
Ring=Right Signal
Tip
Sleeve
Ring
Strain Clamp
Sleeve=Ground/Screen
Use for Headphone
1/4" Stereo (TRS) Jack Plug
Tip
Sleeve
Strain Clamp
Sleeve=Ground/Screen
Use for Mono Line In, Mono 1/4" Jack Plugs
1/4" Mono (TS) Jack Plug
LTO
connectors. It
LTO MONITOR without
Tip=Left Signal
Tip=Signal
5