Dear customer! Thank you for purchasing our product. For safety, it is strongly recommended to read this manual carefully before connecting, operating and/or adjusting the product and keep the manual for reference in the future. Table of contents Table of contents ...............................2 Important safeguards ............................3 Installation/ connection............................4 Panel controls ..............................8...
Important safeguards Using the device at temperature below -10º may cause the breakage of the device. BEFORE USING PLEASE HEAT UP THE PASSENGER COMPARTMENT TO THE RECOMMENDED TEMPERATURE! Read carefully through this manual to familiarize yourself with this high-quality sound system. Disconnect the vehicle's negative battery terminal while mounting and connecting the unit.
Installation/ connection Attention: REMOVE THE TRANSPORT CD STOPPER (2 SCREWS) BEFORE USE. Din front-mount (method 1) After inserting the holder into the dashboard, select the appropriate tab and bend them inwards to secure the holder in place. Insert fingers into the groove in the front of frame and remove it. Insert the levers supplied with the unit to the grooves at both sides.
Page 5
Din rear-mount (method 2) Installation using the screw holes at both sides of the unit. 1. Select a position where the screw holes of the main unit are fitted for aligned, and tighten the screws at 2 positions at each sides. Use either truss screws (5 x 8mm) or flush surface screws (4 x 8mm), depending on the shape of the screw holes in the bracket.
Page 6
Attaching the control panel Insert the right side of the control panel into the main unit. Note: the control panel must be attached into the T-Joint. Press the control panel on to the left side of middle of it until a click sound is heard. Caution: DO NOT insert the control panel from the left side.
Electrical connection Caution: Do not interchange the connection of the wiring!!! For some car models you may need to modify wiring of the supplied power cord. Contact your authorized car dealer before installing this unit.
Panel controls Front panel 1. RELEASE button Press it to detach the front panel. 2. VOL knob/ SEL button Rotate VOL knob clockwise to increase the volume level; rotate anticlockwise to decrease the volume level. Press SEL button once to enter the Audio select menu. Press it repeatedly to select the modes: VOLUME =>...
Page 9
3. IR sensor 4. PWR button Press PWR button to turn the power on, press again to turn the power off. 5. MODE button Press to select the mode: TUNER => CD => SD/MMC => USB => NAND => AUX. 6.
Page 10
16. PAUSE button Use this button to pause playback. Under the pause status, press it to play. 17. PRESET STATION [1-6] buttons 18. AF/REG button Press it to enter the AF mode. Press and hold for 2 seconds to enter the REG mode. 19.
Page 11
Remote control 1. DIS/REC button Press shortly to display current mode and time. Press and hold for 2 seconds to enter the Record function. 2. MODE button Press to select the mode: TUNER => CD => SD/MMC => USB => NAND => AUX. 3.
Page 12
8. TA/TP button Press it to activate the TA function. 9. PTY button Press it to activate the PTY function. 10. AF/REG button Press it to enter the AF mode. Press and hold for 2 seconds to enter the REG mode. buttons Press to go to the previous/ next track.
Page 13
Changing the battery 1. Press the catch and at the same time pull out the battery tray. 2. Insert the 1 x lithium battery, type CR 2025 3V battery with the stamped (+) mark facing upward. Insert the battery tray into the remote control. Warning: Store the battery where children cannot reach.
Page 14
Back of the front panel Press the OPEN button on the front panel to flip it down. 1. MINI USB socket; 2. SD CARD socket; 3. Panel status indicator; 4. RESET button; 5. Disc slot; 6. EJECT button. Note: Pressing the RESET button will erase the clock setting and stored stations. Panel status indicator lights up when you slide the panel down;...
General operation Reset the unit Operating the unit for the first time or after replacing the car battery, you must reset the unit. Press OPEN button on the panel to open the panel and press the RESET buttont to restore the unit to the original factory settings.
Page 16
Setting other characteristics During FM mode, keep pressing SEL button for 2 seconds to enter another mode. Shortly and repeatedly press the SEL button to select the setting: DSP => IN VOL => STEREO => LOC => LOUD => CT => TA VOL => EON =>...
Display operations 1. Press the DIS/ REC button to show the following current tuning information and time in any play mode: PS (Default) => PTY => Radio frequency => CT. 2. Press and hold for 2 seconds to enter the RECORD mode. Setting the time 1.
Page 18
Programming tuner stations You can store up to a total of 30 radio stations in the memory (18 FM, 12 MW), manually or automatically. To store a station: Select a band (if needed) Select a station by T-UP/ T-DN buttons Hold a Preset button (1-6) which you want store the station for at least 2 seconds.
Page 19
The RDS program will be automatically searched and received. After turning on, if the RDS signal is week or even no signal, the unit will search another frequency with this RDS program. Default setting is ON. Region mode: Press and hold AF/REG button for 2 seconds, the unit will be under REGION ON or REGION OFF mode: - REGION ON: PI code will be searched during AF searching.
CD/ NAND/ SD/ MMC/ USB operations Loading a disc 1. Turn the power on. 2. Press the OPEN button on the panel. 3. Insert the disc with the printed side facing upward into the slot. 4. Press EJECT button on the inner side to eject the disc. Inserting the SD/ MMC card/ USB device Insert the MMC/ SD card or USB device into MMC/ SD compartment or USB socket.
Page 22
3. Use the T-DN or T-UP / buttons to go to the previous/ next track by one. Scanning forward and backward Press and hold for 2 seconds the T-DN or T-UP buttons to fast the playing in backward or forward direction. Note: During the disc playback when Fast/ Reverse Playback gets to the beginning of the playing another track, it resumes normal playback.
Page 23
Search function In CD/ NAND/ MMC/ SD/ USB mode, press AS/PS button to enter the Music file search menu. Press again to select the search mode: FILE NUMBER SEARCH => FILE NAME SEARCH => FOLDER SEARCH. Audio CD supports the FILE NUMBER SEARCH only. File number search 1.
File managing Encoding (recording) function Encoding (Recoding) function enables sound source from Tuner, CD, AUX-in, NAND flash memory, USB device, SD socket to record directly to NAND flash memory, USB device or SD/MMC card. Note: Default recoding location is NAND flash memory. Recoding at tuner/ AUX-in mode 1.
Page 25
NAND ALL: Recording all tracks from disc to NAND Flash memory. MMC ALL: Record all tracks from disc to SD/MMC card. USB ALL: Record all tracks from disc to USB storage device. NAND ONE: Recording current track to NAND flash memory. MMC ONE: Record current track to SD/MMC card.
Page 26
Select intended location by pressing DIS/REC button in the sequence of MMC => USB. To exit recording mode, press DIS/REC more than 2 seconds. To start recording, press BAND. Press again to stop recording. 2. In SD/MMC mode: encoding to NAND flash memory or USB socket is available. In USB mode, encoding to NAND Flash Memory or SD/MMC socket is available.
Page 27
File download to front panel You can enjoy the music from pre-recorded memory on flash memory of the front panel. Copy music files from computer using USB cable provided. 1. Check your operation system of your computer - supporting operation system is Windows 98, 2000, XP. Note: Windows XP supports Plug-N-Play, but Windows 2000 and 98 needs install driver before downloading.
MP3 overview Notes on MP3: MP3 is short for MPEG Audio Layer 3 and refers to an audio compression technology standard. This product allows playback of MP3 files on CD-ROM, CD-R or CD-RW discs. The unit can read MP3 files written in the format compliant with ISO 9660. However it does not support the MP3 data written by the method of packet write.
Make sure that when MP3 CD-R or CD-RW is burned that it is formatted as a data disc and NOT as an audio disc. You should not write non-MP3 files or unneeded folders along with MP3 files on the disc otherwise it takes a long time until the unit starts to play MP3 files.
Handling discs Dirty, scratched or warped discs may cause skip ping or noise. Handle the disc only by the edges. To keep clean do not touch its surface. Discs should be stored in their cases after use to avoid scratches. Do not expose discs to direct sunlight, high humidity, high temperature or dust.
Troubleshooting guide Cause Solution Symptom General The car ignition is not on. If the power supply is properly connected to the car No power The fuse is blown. accessory switch the ignition key to ACC . Replace the fuse. Disc Presence of disc inside the player.
Specification General Power supply: 11-16 V DC Current consumption: max. 10 A Maximum power output: 50 W x 4 channels Dimensions (L x W x H): 178 x 175 x 50 mm Working temperature range: -10º - +60º Built-in flash memory: 1 Gb FM Stereo Radio Frequency range:...