Related Manuals for PARKZONE Sport Cub
Summary of Contents for PARKZONE Sport Cub
- Page 1 Sport Cub Instruction Manual / Bedienungsanleitung Manuel d’utilisation / Manuale di Istruzioni...
- Page 2 NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit www.horizonhobby.com and click on the support tab for this product. Meaning of Special Language: The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product: NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND little or no possibility of injury.
-
Page 3: Table Of Contents
9. Perform the AS3X Control Direction Test with the aircraft. 10. Adjust the fl ight controls and transmitter. 11. Perform a radio system Range Check. 12. Find a safe and open area. 13. Plan fl ight for fl ying fi eld conditions. To register your product online, visit www.parkzone.com... -
Page 4: Transmitter And Receiver Binding
Battery Charging Battery Charging Process NOTICE: Charge only batteries that are cool to the touch and are not damaged. Look at the battery to make sure it is not damaged e.g., Refer to the charging warnings. It is recommended to charge the battery while swollen, bent, broken or punctured. -
Page 5: Battery Installation And Esc Arming
Receiver Selection and Installation The Spektrum AR636 receiver is recommended for this airplane. For an AR636 ® receiver purchased separately, download the setup for the ParkZone Sport Cub from www.spektrumrc.com and load it in the receiver, before installing the receiver in the aircraft. If you choose to install another receiver, ensure that it is at least a 4-channel full range (sport) receiver, or 5 or more channels with fl... -
Page 6: Landing Gear Installation
Landing Gear Installation 1. Install 2 tires (A) on the strut (B) using 2 wheel collars (C) and 2 set screws (D). Tighten the set screws on the fl at spots of the strut. Tip: Threadlock may be required to keep the collar on the strut. 2. -
Page 7: Wing Assemby And Installation
Wing Assemby and Installation Assembly 1. Install the vortex generators (A) in the wing channels (B) by using double- sided tape (C). CAUTION: DO NOT crush or otherwise damage the wiring when attaching the wing to the fuselage. 2. Slide the wing tube (D) in the hole in the left wing. 3. -
Page 8: Control Horn And Servo Arm Settings
Flap Installation OPTIONAL IMPORTANT: If desired, install the optional fl aps before installing the wing. Fig. A 1. Install a tube on each clevis (Fig. A). 2. Connect the fl ap servo (PKZ1090, sold separately) to a servo extension (PKZ5403, sold separately). 3. -
Page 9: Dual Rates
Transmitter Setup IMPORTANT: The AR636 receiver installed in the Bind-N-Fly aircraft has been Transmitters DX4e and DX5e pre-programmed for operation in this aircraft. Refer to the receiver manual for correct setup if the receiver is replaced or is used in another aircraft. Before binding for Non-computerized Transmitters (DX4e, DX5e): 1. -
Page 10: Center Of Gravity (Cg)
Center of Gravity (CG) The CG location is 63 - 66mm back from the leading edge of the wing at the root. Make sure the fl ight battery is secured using the hook and loop strap. Aircraft CG and weight is based on an E-fl ite 11.1V 1300mAh 30C battery (EFLB13003S20) installed. -
Page 11: As3X Control Direction Test
AS3X Control Direction Test Perform the Control Direction Test to ensure the aircraft responds cor- Aircraft rectly to your transmitter. Once you are sure the aircraft responds cor- AS3X Reaction movement rectly, move the aircraft as shown to ensure the AS3X system moves the control surfaces in their proper direction. -
Page 12: Flying Tips
Flying Tips Consult local laws and ordinances before choosing a fl ying location. NOTICE: If a crash is imminent, reduce the throttle and trim fully. Failure to do so could result in extra damage to the airframe, as well as damage to the Range Check your Radio System ESC and motor. -
Page 13: Motor Service
Motor Service Disassembly Assembly CAUTION: Always disconnect the fl ight battery from the aircraft before Assemble in reverse order. removing the propeller. • Correctly align and connect the motor wire colors with the ESC wires. 1. Remove the screw (A) and spinner (B) from the collet (C). •... -
Page 14: Troubleshooting Guide
Troubleshooting Guide Problem Possible Cause Solution Aircraft will not re- Throttle not at lowest position or throttle trim too high Reset controls with throttle stick and throttle trim at lowest setting spond to throttle but Throttle servo travel is lower than 100% Make sure throttle servo travel is 100% or greater responds to other Throttle channel is reversed... -
Page 15: Limited Warranty
Limited Warranty What this Warranty Covers you may need any assistance. For questions or assistance, please visit our Horizon Hobby, LLC. (“Horizon”) warrants to the original purchaser that the website at www.horizonhobby.com, submit a Product Support Inquiry, or call product purchased (the “Product”) will be free from defects in materials and the toll free telephone number referenced in the Warranty and Service Contact workmanship at the date of purchase. -
Page 16: Compliance Information For The European Union
Compliance Information for the European Union Declaration of Conformity Declaration of Conformity (in accordance with ISO/IEC 17050-1) (in accordance with ISO/IEC 17050-1) No. HH2014041002 No. HH2014041001 Product(s): Sport Cub BNF Product(s): Sport Cub PNP Item Number(s): PKZ6880 Item Number(s): PKZ6875 Equipment class:... -
Page 17: Replacement Parts
Cône : Sport Cub Ogiva: Sport Cub PKZ6806 Landing gear set: Sport Cub Fahrwerk-Set: Sport Cub Jeu de train d'atterrissage principal : Sport Cub Set del carrello di atterraggio: Sport Cub PKZ6804 Tail Set: Sport Cub Leitwerk: Sport Cub Empennages : Sport Cub... -
Page 18: Optional Parts
Set de fl otteurs : Super Cub LP Set galleggianti: Super Cub LP Cub LP Servo digitale DSV130, ingranaggi PKZ1090 DSV130 digital servo, metal gear Parkzone DSV130 Digitalservo MG Servo DSV130 digital, pignons métal metallo PKZ5403 Servo Extension Querruderservoverlängerung Rallonge de servo Prolunga per servo 1.5A AC Power Supply... - Page 19 Futaba is a registered trademark of Futaba Denshi Kogyo Kabushiki Kaisha Corporation of Japan. Cub Crafters, Sport Cub, associated emblems and logos, and body designs of vehicles are either registered trademarks or trademarks of Cub Crafters, Inc. and are used with permission.