PARKZONE Typhoon 3D Instruction Manual
  1. Manuals
  2. Brands
  3. PARKZONE Manuals
  4. Toy
  5. Typhoon 3D
  6. Instruction manual

PARKZONE Typhoon 3D Instruction Manual

Plug-n-play charge-and-fly park flyer
Hide thumbs Also See for Typhoon 3D:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Instruction Manual

Instruction Manual

Charge-and-Fly
Typhoon 3D
Park Flyer
™
Wingspan: 39.5 in (1000mm)
Required: 4-channel transmitter (minimum)
Overall Length: 34 in (862mm)
Flying Weight: 26 oz (740 g)
Motor: ParkZone BL400-15T
brushless with gearbox
4-channel receiver (minimum)
3S 2100mAh Li-Po battery or
9-cell 1000mAh Ni-MH battery

Advertisement

Table of Contents
loading

Related Manuals for PARKZONE Typhoon 3D

Summary of Contents for PARKZONE Typhoon 3D

  • Page 1: Instruction Manual

    Typhoon 3D Instruction Manual Wingspan: 39.5 in (1000mm) Required: 4-channel transmitter (minimum) Charge-and-Fly Park Flyer Overall Length: 34 in (862mm) 4-channel receiver (minimum) ™ Flying Weight: 26 oz (740 g) 3S 2100mAh Li-Po battery or Motor: ParkZone BL400-15T 9-cell 1000mAh Ni-MH battery...
  • Page 2 Warning This airplane comes almost fully assembled in order to allow you to get in the air quickly. Your Typhoon 3D Although your ParkZone Typhoon 3D PNP comes almost Plug-N-Play (PNP) already has the 3-wire servos, a ready to fly, this aircraft is for experienced RC pilots only...

  • Page 3: Installing Landing Gear

    Wing Tab Wing Tab in order to do more extreme maneuvers with your Typhoon 3D PNP. Always check ailerons prior to flight to make sure they are not reversed! Trim adjustments to the ailerons may be necessary prior to flight.
  • Page 4 Step 4 Attaching the Horizontal Stabilizer and Rudder 1. Locate horizontal stab. 2. Carefully slide horizontal stab into fuselage, making sure control surface horn is on top. 3. Use included strips (4 pieces) of clear tape to secure stab to tail fillet. You should use 1 strip for top and bottom of each side.

  • Page 5: Installing The Propeller And Spinner

    (PKZ1027), or by the Thunder Power 3S 2100mAh Aileron, Elevator, and Rudder Throws battery pack (THP21003S). The center of gravity (CG) for your Typhoon 3D PNP, with The recommended throws in low rate are: the 9-cell Ni-MH pack, is approximately 3.50 inches Ailerons: +/- .75 inches (20mm)

  • Page 6: Programming Your Esc

    Li-Po battery pack. Using the Thunder Power 3S battery Li-Po – up (see above) will greatly increase the power, performance, and flight time of your Typhoon 3D PNP. Ni-MH – down (stock setting) The ESC comes with the auto-cut voltage set for the After the setting of this parameter, the controller will 9-cell Ni-MH battery pack.

  • Page 7: Range Checking Your Radio System

    Flying Always choose a wide-open space to fly your ParkZone Typhoon 3D PNP. It is ideal for you to fly at an AMA sanctioned flying field. If you are not flying at an AMA approved site, always avoid flying near houses, trees, wires, and buildings.

  • Page 8: Non-Warranty Service

    Horizon Hobby, Inc. directly Champaign, IL 61822 regarding any warranty questions. Please do not We suggest you ship your Typhoon 3D PNP via a carrier contact your local hobby shop regarding warranty that provides package tracking and/or signature required.

  • Page 9: Replacement Parts

    PKZ4130 Mini Servo (3W) with Arms: Typhoon 3D $12.99 PKZ1131 Servo Gear with Accessories $2.49 PKZ4167 Bare Fuselage with Tube and Parts: Typhoon 3D $28.99 PKZ4176 Instruction Manual: Typhoon 3D PNP $.99 Optional Parts THP21003SPL Thunder Power 3S 2100mAh Li-Po Battery Pack $84.95...
  • Page 10 PKZ4176 0 5 4 8 2 1 4 5 5 3 ParkZone products are distributed exclusively by Horizon Hobby, Inc. 4105 Fieldstone Road Champaign, IL 61822 ©2005 Horizon Hobby, Inc. www.parkzone.com 7899.1...

Table of Contents