Sharp FO-5700 Service Manual page 35

SW31 No. 6 ~ No. 8 The second priority cassette
To select the second priority cassette.
000: Not used (To set in case of using only paper
feeder that has been set in the first priority
cassette)
001: 1st paper feeder (MP-TRAY)
010: 2nd paper feeder
011: 3rd paper feeder
Except the above Setting forbidden (Not used)
SW32 No. 1 ~ No. 3 The third priority cassette
To select the third priority cassette.
000: Not used (To set in case of using only paper
feeder that has been set in the first /second
priority cassette)
001: 1st paper feeder (MP-TRAY)
010: 2nd paper feeder
011: 3rd paper feeder
Except the above Setting forbidden (Not used)
SW32 No. 4 ~ No. 7 Reserved
Set to "0".
SW32 No. 8 Print hold function
When set to "1", the print hold function is enabled.
SW33 No.1, No. 2 Heater mode
Used to set ON/OFF of the heater. Three settings are available: always
ON, always OFF, and OFF timer. (Only when Off timer is selected, SW34-
SW37 settings are valid.)
To set performance of the heater at the printer fixing part.
00: Normally ON (Off in case of Save Mode,
giving priority to Energy Save Mode)
01: Normally OFF
Except the above Setting forbidden (Normally OFF)
SW33 No. 3 ~ No. 5 Density adjustment of print bias
The density of printing is set.
It can be also set in the print diagnosis mode.
SW33 No. 6, No. 7 Drum life limit
The drum life -over judgment conditions are set.
SW33 No. 8 Reserved
Set to "0".
SW34 No. 1 The default resolution for copying
In case of copying without pressing the RESOLUTION key, resolution
will be super fine.
SW34 No. 2 ~ No. 8 Reserved
Set to "0".
SW35 No. 1 Reserved
Set to "0".
SW35 No. 2 ~ No. 4 Reserved
Set to "1".
SW35 No. 5 Reserved
Set to "0".
SW35 No.6, No. 7 Reserved
Set to "1".
SW35 No.8 Reserved
Set to "0".
SW36 No. 1, No. 2 Reserved
Set to "0".
SW36 No. 3 Reserved
Set to "1".
SW36 No. 4 ~ No. 7 Reserved
Set to "0".
SW36 No. 8 Reserved
Set to "1".
SW37 No. 1 ~ No. 8 Delay time after PC printing (n second )
To insert delay time after PC printing.
SW38 No. 1 ~ No. 8 Reserved
Set to "0".
SW39 No. 1 ~ No. 8 Reserved
Set to "0".
SW40 No. 1 ~ No. 8 Reserved
Set to "0".
SW41 No. 1 ~ No. 8 Reserved
Set to "0".
SW42 No. 1 ~ No. 8 Reserved
Set to "0".
SW43 No. 1 ~ No. 5 Reserved
Set to "0".
SW43 No. 6 ~ No. 8 Data reduction
Reduction ratio of receiving is set .
It can be changed even in the optional mode.
To set printing reduction rate of received images.
000: Automatic
100: 100%
Except the above 100%
SW44 No. 1 Automatic printing of activity report
This soft switch is used to select; whether or not to produce the activity
report when the memory is full (about 50 items). An activity report can
be produced when the following key entry command is made.
"FUNC", "2", "#", "START"
After producing the activity report, all the data in the memory will be
cleared.
When the switch function is set to "0" (NO), the data in memory will be
deleted from the oldest as it reaches the maximum memory capacity
(approx. 50 items).
SW44 No. 2 Printout of total time and total number of pages on
activity report
Used to make a choice of whether the total communication time and
pages are recorded in the activity report.
SW44 No. 3 Reserved
Set to "0".
2 – 31
FO-5700U