Sharp UX-8 Service Manual
  1. Manuals
  2. Brands
  3. Sharp Manuals
  4. Fax Machine
  5. UX-8
  6. Service manual
Sharp UX-8 Service Manual

Sharp UX-8 Service Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Illustration: UX-8
This service manual is omitted because it is partly common to UX-60TH/FO-70TH of the service manual of the
previous issue. Those common parts are to refer to the service manual of UX-60TH/FO-70TH (00ZUX60TH/SME).
[1] Specifications ............................................ 1-1
[2] Operation panel ......................................... 1-2
[3] Transmittable documents .......................... 1-3
[4] Installation ................................................. 1-4
[5] Quick reference guide ............................... 1-9
[1] Adjustments .............................................. 2-1
[3] Troubleshooting ...................................... 2-18
[4] Error code table ....................................... 2-19
[1] General description ................................... 3-1
[2] Disassembly and assembly
procedures ....................................... 3-3
[1] Block diagram ............................................4-1
[2] Wiring diagram .......................................... 4-2
[3] Point-to-point diagram ............................... 4-3
Parts marked with "
" is important for maintaining the safety of the set. Be sure to replace these parts with specified ones for
maintaining the safety and performance of the set.
SERVICE MANUAL
CONTENTS
SHARP CORPORATION
FACSIMILE
MODEL
CHAPTER 5. CIRCUIT DESCRIPTION
[1] Refer to the service manual of UX-60TH.
[2] Refer to the service manual of UX-60TH.
[3] Refer to the service manual of UX-60TH.
[4] Refer to the service manual of UX-60TH.
[5] Refer to the service manual of UX-60TH.
CHAPTER 6. CIRCUIT SCHEMATICS AND
PARTS LAYOUT
[1] Control PWB circuit ................................... 6-1
[2] TEL/LIU PWB circuit .................................. 6-9
[3] Power supply PWB circuit ...................... 6-13
[4] Operation panel PWB circuit ................... 6-15
CHAPTER 7. OPERATION FLOWCHART
[1] Refer to the service manual of UX-60TH.
[2] Refer to the service manual of UX-60TH.
CHAPTER 8. OTHERS
[1] Refer to the service manual of UX-60TH.
[2] Refer to the service manual of UX-60TH.
PARTS GUIDE
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
UX-8TH/UX-40TH
GQ-5TH/FO-50TH
No. 00ZUX8TH//SME
UX-8
UX-40
GQ-5
FO-50

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the UX-8 and is the answer not in the manual?

Questions and answers

林美惠
April 11, 2025

螢幕出現Document Jammed 無法排除

0
1 comments:
Mr. Anderson
April 11, 2025

To fix a Document Jammed error on the Sharp UX-8:

1. Grasp the finger hold and pull up to open the operation panel.
2. Flip up the green levers on each side of the white roller.
3. Remove the jammed document.
4. Close the operation panel, pressing down on both front corners until it clicks into place.

Important: Do not try to remove the document before releasing it using the steps above, as this may damage the feeder mechanism.

This answer is automatically generated

0

Subscribe to Our Youtube Channel

Related Manuals for Sharp UX-8

Summary of Contents for Sharp UX-8

  • Page 1: Table Of Contents

    UX-40 GQ-5 FO-50 MODEL Illustration: UX-8 This service manual is omitted because it is partly common to UX-60TH/FO-70TH of the service manual of the previous issue. Those common parts are to refer to the service manual of UX-60TH/FO-70TH (00ZUX60TH/SME). CONTENTS CHAPTER 1.
  • Page 2 UX-8TH/UX-40TH GQ-5TH/FO-50TH CAUTION FOR BATTERY REPLACEMENT (Danish) ADVARSEL ! Lithiumbatteri-Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. (English) Caution ! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer.

  • Page 3: Chapter 1. General Description

    Length: 140 to 600 mm As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for procduct improvement without prior notice. The performance specifications figures indicated are nominal values of production units. There may be some deviation from these values in individual units.

  • Page 4: Operation Panel

    Press one of these keys to dial a fax number automatically. a copy of a document. At any other time, press this key to Note for UX-8/GQ-5: Rapid Key Dialing is not available. print out the Help List, a quick reference guide to the 2.

  • Page 5: Transmittable Documents

    UX-8TH/UX-40TH GQ-5TH/FO-50TH [3] Transmittable documents 5. Automatic Document Feeder Capacity Number of pages that can be placed into the feeder at anytime is as 1. Document Sizes follows: Normal size: max. ADF 5 sheets width 148 – 216 mm Normal size Special size: single sheet only (manual feed) length 140 –...

  • Page 6: Installation

    UX-8TH/UX-40TH GQ-5TH/FO-50TH TELEPHONE JACK 7. Use of Document Carrier Sheet A standard telephone jack must be located near the machine. A document carrier sheet must be used for the following documents. This is the telephone jack commonly used in most homes and offices. •...
  • Page 7 UX-8TH/UX-40TH GQ-5TH/FO-50TH Insert one end of the line cord into the jack on the back of the ma- Flip up the front paper guide. chine marked TEL. LINE. Insert the other end into a standard single- line wall telephone jack. Note: Do not peel off or bend this strip of film.
  • Page 8 UX-8TH/UX-40TH GQ-5TH/FO-50TH 4. Loading the fax paper (FO-20PRw) Insert the leading edge of the paper into the slot as shown. Continue to push the paper through the slot until it comes out the opening in • Your fax machine prints incoming faxes on a special kind of paper the front of the machine.
  • Page 9 UX-8TH/UX-40TH GQ-5TH/FO-50TH 5. Clearing a jammed document Flip down the green levers on each side of the white roller. If the original document doesn’t feed properly during transmission or copying, or DOCUMENT JAMMED appears in the display, first try press- ing the START key.
  • Page 10 UX-8TH/UX-40TH GQ-5TH/FO-50TH 6. Clearing jammed paper Cut off the wrinkled part of the paper. If the fax paper jams, PAPER JAMMED will appear in the display. Follow the steps below to clear the jam. Grasp the finger hold and pull up to open the operation panel. Reload the paper.

  • Page 11: Quick Reference Guide

    3. Enter a 2-digit Speed Dial number (from 01 to 05 for Rapid Key Dialing, or 06 to 40 for Speed Dialing) (If you are clearing a number, go to Step 7.) (UX-8: 01 to 4. Enter the full fax/telephone number.
  • Page 12 UX-8TH/UX-40TH GQ-5TH/FO-50TH M E M O 1 – 10...

  • Page 13: Chapter 2. Adjustments

    UX-8TH/UX-40TH GQ-5TH/FO-50TH CHAPTER 2. ADJUSTMENTS 3. Settings Dial mode selector [1] Adjustments DIAL mode (Soft Switch No. SWB4 DATA No. 2) (step 1) Select "OPTION SETTING". General KEY : FUNCTION Since the following adjustments and settings are provided for this model, make adjustments and/or setup as necessary.

  • Page 14: Diagnostics And Service Soft Switch

    UX-8TH/UX-40TH GQ-5TH/FO-50TH [2] Diagnostics and service soft switch 1. Operating procedure (1) Entering the diagnostic mode Press FUNC → 9 → → 8 → # → 7 , and the following display will appear. ROM Ver. FZJ0 (FZK0 ) After 2 sec: DIAG MODE FZJ0 (UX-8TH/GQ-5TH) FZK0...
  • Page 15 UX-8TH/UX-40TH GQ-5TH/FO-50TH 3. Diagnostic items description 3. 6. Signal send mode 3. 1. Soft switch mode This mode is used to send various signals to the circuit during FAX com- munication. Every push of START key sends a signal in the following The soft switches are provided so that each operation mode can be set sequence.
  • Page 16 UX-8TH/UX-40TH GQ-5TH/FO-50TH 3. 12. Entry data receive 3. 13. Country select This mode is used to set line connecting parameters which correspond This mode is used to receive the registered data from the other machine to each destination. and to make your machine register the received data. Before receiving When the country select mode is selected, and then the START key is in this mode, it is necessary to set the other machine at the entry data pressed, the destination (country name) currently set will be displayed.
  • Page 17 UX-8TH/UX-40TH GQ-5TH/FO-50TH 5. Soft switch description • Soft switch Switch setting and function DATA Initial ITEM Remarks setting Protect from echo Forced 4800bps reception Footer Print Length limitation of copy/send/receive No limit Copy/Send:60cm Receive:1.5m CSI transmission Not transmitted Transmitted DIS receive acknowledgement during G3 Twice NSF:Once transmission...
  • Page 18 Disconnect the line when DIS is received in RX mode Equalizer freeze control(MODEM) Equalizer freeze control 7200 bps only CNG transmission in manual TX mode Initial compression scheme for sharp fax in MR mode H2 mode TX mode Modem speed automatic down when RX...
  • Page 19 UX-8TH/UX-40TH GQ-5TH/FO-50TH Switch setting and function DATA Initial ITEM Remarks setting Auto dial mode Delay timer of after line 1.7s 2.0s 2.5s 3.0s 3.6s 4.0s 5.5s 7.0s connect No. 1 No. 2 No. 3 Fax signal detection after telephone mode dial Reserved Reserved Reserved...
  • Page 20 UX-8TH/UX-40TH GQ-5TH/FO-50TH Switch setting and function DATA Initial ITEM Remarks setting Reserved Reserved Reserved Reserved Reserved Caller ID function Reserved Reserved CI off detection timer Binary input (0~1550ms setting by 50ms step) No. = 16 8 4 2 1 2 3 4 5 1 1 1 0 Reserved Reserved...
  • Page 21 UX-8TH/UX-40TH GQ-5TH/FO-50TH Switch setting and function DATA Initial ITEM Remarks setting DTMF detection time 50ms 80ms 100ms 120ms No. 1 No. 2 Protection of remote reception(5 detection Remote reception with GE telephone Compatible Not compatible Remote operation code figure by external Binary input OPTION TEL (0~9)
  • Page 22 UX-8TH/UX-40TH GQ-5TH/FO-50TH Switch setting and function DATA Initial ITEM Remarks setting Busy tone continuous sound detect time 5 sec 10 sec Reserved Busy tone detect continuation sound detect Reserved Busy tone detect intermittent sound detect Busy tone detection pulse number 2 pulses 4 pulses 6 pulses...
  • Page 23 UX-8TH/UX-40TH GQ-5TH/FO-50TH Switch setting and function DATA Initial ITEM Remarks setting Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved Reserved...
  • Page 24 UX-8TH/UX-40TH GQ-5TH/FO-50TH Switch setting and function DATA Initial ITEM Remarks setting Communication results printout Error Send only Always No print OPTION (Transaction report) No. 1 No. 2 No. 3 Time format 12 hour 24 hour Date format Month-Day-Year Day-Month-Year Reserved Reserved Reserved Entering diag mode by pressing SPEED key Yes...
  • Page 25 UX-8TH/UX-40TH GQ-5TH/FO-50TH SW-A2 No. 6 H2 mode • Soft switch function description Used to determine reception of H2 mode (15 sec transmission mode). SW-A1 No. 1 Protect from echo When set to OFF, H2 mode reception is inhibited even though the trans- mitting machine has H2 mode function.
  • Page 26 When using the 40% make ratio pulse dial, set to 1. When set to "0", if the other fax is Sharp model, fax transmit the docu- SW-B4 No. 5, No. 6 Auto dial mode Delay timer of before line con- ment by H2 mode.
  • Page 27 UX-8TH/UX-40TH GQ-5TH/FO-50TH SW-B5 No. 1 ~ No. 3 Auto dial mode Delay timer of after line con- SW-C1 No. 5 Line density selection nect Used to set the transmission mode which is automatically selected when Delay time between the line connection and dial data output under the the Resolution key is not pressed.
  • Page 28 UX-8TH/UX-40TH GQ-5TH/FO-50TH SW-D3 No. 1 ~ No. 5 CI off detection timer SW-E3 No. 1 Disconnect the line when DTMF "#" is received during (0~1550ms setting by 50ms step) TEL/FAX automatic switching mode Set the minimum time period of CI signal interruption which affords to be When set to "1", if machine detects the DTMF code # during phone/fax judged as a CI OFF section with 50ms steps.
  • Page 29 UX-8TH/UX-40TH GQ-5TH/FO-50TH SW-G4 No. 1 ~ No. 6 Quiet detect level setting SW-I8 No. 1 ~ No. 8 Reserved (0~-44dBm setting by 1dBm step) Set to "0". This is used to change the quiet detect level setting. SW-J1 No. 1 Sender's phone number setting If quiet detection is difficult due to noise, reduce this setting level.

  • Page 30: Troubleshooting

    UX-8TH/UX-40TH GQ-5TH/FO-50TH [3] Troubleshooting Refer to the following actions to troubleshoot any of the problems men- • Apply line equalization SOFT SWITCH A5-1, 2. tioned in 1-4. May be used in case [1] [2] [3] [4]. [1] A communication error occurs. •...

  • Page 31: Error Code Table

    UX-8TH/UX-40TH GQ-5TH/FO-50TH [4] Error code table 1. Communication error code table G3 Transmission Code Final received signal Error Condition (Receiver side) Incomplete signal frame Cannot recognize bit stream after flag NSF, DIS Cannot recognize DCS signal by echo etc. Cannot recognize NSS signal (FIF code etc) Disconnects line during reception (carrier missing etc) Disconnects line by fall back Disconnects line during reception of multi page...

  • Page 32: Chapter 3. Mechanism Blocks

    UX-8TH/UX-40TH GQ-5TH/FO-50TH CHAPTER 3. MECHANISM BLOCKS 3-2. Automatic document feed 1) Use of the paper feed roller and separation rubber plate ensures er- ror-free transport and separation of documents. The plate spring [1] General description presses the document to the paper feed roller to assure smooth feed- ing of the document.
  • Page 33 UX-8TH/UX-40TH GQ-5TH/FO-50TH 5. Recording block Separation rubber Last page of document (UX-40/FO-50 ONLY) 5-1. General view Back of document Recording paper First page of document Scanner frame Platen roller Feed plate PO guide Paper feed roller (UX-40/FO-50 ONLY) Fig. 4 3-5.

  • Page 34: Disassembly And Assembly Procedures

    UX-8TH/UX-40TH GQ-5TH/FO-50TH [2] Disassembly and assembly procedures • This chapter mainly describes the disassembly procedures. For the assembly procedures, reverse the disassembly procedures. • Easy and simple disassembly/assembly procedures of some parts and units are omitted. For disassembly and assembly of such parts and units, refer to the Parts List.
  • Page 35 UX-8TH/UX-40TH GQ-5TH/FO-50TH Parts list (Fig. 2) CIS unit and scanner frame Part name Q’ty Part name Q’ty Document guide lower Feed roller Back roller gear (UX-40/FO-50 only) Back roller bearing, left Connector CIS release lever, left CIS support, left Back roller CIS support, right CIS release lever, right CIS unit...
  • Page 36 UX-8TH/UX-40TH GQ-5TH/FO-50TH Operation panel unit, drive unit, hopper Parts list (Fig. 3) guide Part name Q’ty Part name Q’ty Mechanism unit Operation panel unit/ Connector document guide upper unit Operation panel unit Screw Connector Pinion gear Screw (3×12) Hopper spring Hopper guide, left Drive unit Screw (3×8)
  • Page 37 Parts list (Fig. 4) upper Part name Q’ty Part name Q’ty Screw (3×8) Document guide piece Connector (UX-8/GQ-5 only) Door sensor Document guide upper Blind sheet Screw (2×6) Document guide upper unit Connector Operation panel unit Operation panel PWB unit...
  • Page 38 UX-8TH/UX-40TH GQ-5TH/FO-50TH Parts list (Fig. 5) Drive unit frame Part name Q’ty Part name Q’ty Cam spring Planet lever B Cam switch Planet gear Cam gear Planet gear spring Mode lever Reduction gear, 17/30Z Planet gear Reduction gear, 17/43Z Planet gear spring Idler gear, 25Z Planet lever A Screw (3×8)
  • Page 39 UX-8TH/UX-40TH GQ-5TH/FO-50TH Parts list (Fig. 6) Release lever, head guide and PO guide Part name Q’ty Mechanism unit Screw (3×8) PO guide Release lever Head guide Fig. 6 3 – 8...
  • Page 40 UX-8TH/UX-40TH GQ-5TH/FO-50TH Head frame unit Parts list (Fig. 7) Part name Q’ty Mechanism unit Screw (3×6) Connector Screw (3×8) Head earth cable Head frame unit Screw (3×8) Panel lock lever spring Control Fig. 7 3 – 9...
  • Page 41 UX-8TH/UX-40TH GQ-5TH/FO-50TH Parts list (Fig. 8) Head frame and thermal head Part name Q’ty Part name Q’ty Platen gear Screw (3×6) Platen bearing Head holder, right Platen roller Thermal head Connector Head spring 2 Screw (3×6) Head spring 1 Head holder, left Head frame Fig.
  • Page 42 UX-8TH/UX-40TH GQ-5TH/FO-50TH PWB case top, bottom, PWB and Parts list (Fig. 9) speaker Part name Q’ty Part name Q’ty Mechanism unit Screw (3×8) Screw (3×8) Hook switch joint lever Connector PWB case, top Connector PWB case, bottom unit PWB case unit Screw (3×6) Screw (3×8) TEL/LIU PWB unit...
  • Page 43 UX-8TH/UX-40TH GQ-5TH/FO-50TH Wire treatment Parts list (Fig. 10) Part name Q’ty Core (F2125) Screw (3×6) Screw (4×6) Screw (3×6) Band (100mm) Band (100mm) (UX-40/FO-50 only) Core (F2123) (UX-40/FO-50 only) Screw (3x8) Door sensor cable Panel Door sensor cable cable Operation Panel cable panel PWB Door...

  • Page 44: Chapter 4. Diagrams [1] Block Diagram

    UX-8TH/UX-40TH GQ-5TH/FO-50TH CHAPTER 4. DIAGRAMS [1] Block diagram 4 – 1...

  • Page 45: Wiring Diagram

    UX-8TH/UX-40TH GQ-5TH/FO-50TH [2] Wiring diagram CNPN 4 – 2...

  • Page 46: Point-To-Point Diagram

    UX-8TH/UX-40TH GQ-5TH/FO-50TH [3] Point- to-point diagram CNMT TPAD TPAD TPBD TPBD TPAD TPAD TX/RX TPBD TPBD MOTOR CNLIUA CNLIUA TELOUT TELOUT TELIN TELIN TEL/LIU TELMUTE TELMUTE CNTH STRB1 STRB1 RXIN RXIN STRB2 STRB2 TXOUT TXOUT N.C. RANK THERMAL +24V +24V HEAD STRB3 STRB3...
  • Page 47 UX-8TH/UX-40TH GQ-5TH/FO-50TH CHAPTER 6. CIRCUIT SCHEMATICS AND PARTS LAYOUT VBAT 270 x 4 C135 2200P RESET PWRDWN (1-1I) C138 XOUT 270 x 4 32.768KHz TSTCLK SYSCLK SYSCLK (3-3A) MIRQ R105 33K C139 MIRQ (3-3B) R106 33K +VREF RESET +VREF (5-2D) –VREF R107 33K DEBUG...
  • Page 48 UX-8TH/UX-40TH GQ-5TH/FO-50TH 6 – 2...
  • Page 49 UX-8TH/UX-40TH GQ-5TH/FO-50TH XTL1 VAA-P(+5VIAA) N.C./SOUT-S AGND5 SR3IN AGND4 SOUT-P AGND3 N.C./ICLK-S AGND2 ICLK-P AGND1 IA1CLK N.C./SIN-S N.C./AVDD-S(+3.3VIAD) SIN-P +3.3V DVAA(+3.3VDA) SR4OUT N.C./MCLK-S VGG(+5VDD) IACLK MCLK-P DGND6 N.C./FSYNC-S DGND5 SA1CLK DGND4 FSYNC-P DGND3 N.C./CTRLSIN-S DGND2 CTRLSIN-P DGND1 SR1IO AVDD-P(+3.3VIAD) EYEXY VDD5(+3.3VDD) EYECLK +3.3V VDD4(+3.3VDD)
  • Page 50 UX-8TH/UX-40TH GQ-5TH/FO-50TH 6 – 4...
  • Page 51 UX-8TH/UX-40TH GQ-5TH/FO-50TH 6 – 5...
  • Page 52 UX-8TH/UX-40TH GQ-5TH/FO-50TH 6 – 6...
  • Page 53 UX-8TH/UX-40TH GQ-5TH/FO-50TH Control PWB parts layout (Top side) 6 – 7...
  • Page 54 UX-8TH/UX-40TH GQ-5TH/FO-50TH Control PWB parts layout (Bottom side) 6 – 8...
  • Page 55 UX-8TH/UX-40TH GQ-5TH/FO-50TH 1SS133 6 – 9...
  • Page 56 UX-8TH/UX-40TH GQ-5TH/FO-50TH 6 – 10...
  • Page 57 UX-8TH/UX-40TH GQ-5TH/FO-50TH TEL/LIU PWB parts layout (Top side) 6 – 11...
  • Page 58 UX-8TH/UX-40TH GQ-5TH/FO-50TH TEL/LIU PWB parts layout (Bottom side) 6 – 12...
  • Page 59 UX-8TH/UX-40TH GQ-5TH/FO-50TH UPC29M05AHF 2SC4210 2SD2114K 6 – 13...
  • Page 60 UX-8TH/UX-40TH GQ-5TH/FO-50TH Power supply PWB parts layout (Top side) Power supply PWB parts layout (Bottom side) Q4 ZD5 6 – 14...
  • Page 61 UX-8TH/UX-40TH GQ-5TH/FO-50TH 6 – 15...
  • Page 62 UX-8TH/UX-40TH GQ-5TH/FO-50TH M E M O 6 – 16...
  • Page 63 UX-8TH/UX-40TH GQ-5TH/FO-50TH PARTS GUIDE UX-8 UX-40 GQ-5 FO-50 MODEL CONTENTS Packing material & Accessories Cabinet, etc. Control PWB unit Scanner unit TEL-Liu PWB unit Upper cabinet Power supply PWB unit Document guide upper Index Drive unit Because parts marked with "...

  • Page 64: Cabinet, Etc

    UX-8TH/UX-40TH GQ-5TH/FO-50TH [1] Cabinet, etc. DOCUMENT GUIDE UPPER B7x2 SCANNER UNIT B7x2 DRIVE UNIT B3x2 – 1 –...
  • Page 65 UX-8TH/UX-40TH GQ-5TH/FO-50TH PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [1] Cabinet etc. DCEKP481BXH18 Operation panel unit DCEKP481BXH04 Operation panel unit [40] DCEKP481BXH19 Operation panel unit DCEKP481BXH05 Operation panel unit [50] CCNW-212AXH01 Panel cable ass’y MSPRC2954XHZZ Hopper spring NGERP2318XHZZ Pinion gear PGIDM2560XHSD Hopper,guide,left PGIDM2561XHSD...
  • Page 66 UX-8TH/UX-40TH GQ-5TH/FO-50TH [2] Scanner unit 20 15 : UX-40/FO-50 ONLY PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [2] Scanner unit LBSHP2110XHZZ Back roller bearing LFRM-2209XHZZ Scanner frame LHLDZ2180XHZZ CIS support,left LHLDZ2181XHZZ CIS support,right MLEVP2317XHZZ CIS release lever MSPRC3117XHZZ CIS spring NGERH2479XHZZ Back roller gear NGERH2480XHZZ...

  • Page 67: Upper Cabinet

    (Unit) DCEKP481BXH18 Operation panel unit DCEKP481BXH04 Operation panel unit [40] DCEKP481BXH19 Operation panel unit DCEKP481BXH05 Operation panel unit [50] [4] Document guide upper UX-8/GQ-5 ONLY UX-40/ FO-50 ONLY PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [4] Document guide upper...

  • Page 68: Drive Unit

    UX-8TH/UX-40TH GQ-5TH/FO-50TH [5] Drive unit PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [5] Drive unit LFRM-2207XHZZ Drive unit frame LPLTM3049XHZZ Motor plate MCAMP2027XHZZ MLEVP2311XHZZ Planet lever A MLEVP2312XHZZ Planet lever B MLEVP2314XHZZ Mode lever MSPRC2735XHZZ Planet gear spring MSPRC3110XHZZ Cam spring NGERH2278XHZZ Planet gear...

  • Page 69: Packing Material & Accessories

    UX-8TH/UX-40TH GQ-5TH/FO-50TH [6] Packing material & Accessories FAX PAPER TAPE TAPE TAPE ORIGINAL DOCUMENT SUPPORT SIDE AC CORD TAPE PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [6] Packing material & Accessories TINST4026XHZZ Operation manual DUNTK468BXHPU Handset QCNW-3976XHBG Handset cord [8/40] QCNW-3976XHOG Handset cord...

  • Page 70: Control Pwb Unit

    UX-8TH/UX-40TH GQ-5TH/FO-50TH PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [7] Control PWB unit UBATL2046SCZZ Battery(CR2032T34) [BAT1] VCKYTV1HB102K Capacitor(50WV 1000PF) [C1] VCKYTV1HB102K Capacitor(50WV 1000PF) [C2] VCKYTV1EF104Z Capacitor(25WV 0.1µF) [C3] VCKYTV1HB103K Capacitor(50WV 0.01µF) [C4] VCEAGA1HW106M Capacitor(50WV 10µF) [C5] VCKYTV1EF104Z Capacitor(25WV 0.1µF) [C6] VCEAGA1HW106M Capacitor(50WV 10µF)
  • Page 71 UX-8TH/UX-40TH GQ-5TH/FO-50TH PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [7] Control PWB unit VCKYTV1HB102K Capacitor(50WV 1000PF) [C172] VCKYTV1HB102K Capacitor(50WV 1000PF) [C173] QCNCM7014SC0G Connector(7pin) [CNCIS] QCNCM2442SC0B Conector(2pin) [CNCSW] QCNCM705BAF06 Connector(2pin) [CNDR] QCNCM7014SC0B Connector(2pin) [CNFRS][40/50] QCNCW2500SC1B Connector(12pin) [CNLIUA] QCNCM7014SC0F Connector(6pin) [CNMT] QCNCM7014SC1F Connector(16pin) [CNPN]...

  • Page 72: Tel-Liu Pwb Unit

    UX-8TH/UX-40TH GQ-5TH/FO-50TH PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [7] Control PWB unit Resistor(1/10W 33KΩ ±5%) VRS-TS2AD333J [R135] Resistor(1/10W 0Ω ±5%) VRS-TS2AD000J [R136] Resistor(1/10W 0Ω ±5%) VRS-TS2AD000J [R138] Resistor(1/10W 220KΩ ±5%) VRS-TS2AD224J [R139] Resistor(1/10W 15KΩ ±5%) VRS-TS2AD153J [R140] Resistor(1/10W 20KΩ ±5%) VRS-TS2AD203J [R141] Resistor(1/10W 30KΩ...

  • Page 73: Power Supply Pwb Unit

    UX-8TH/UX-40TH GQ-5TH/FO-50TH PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [8] TEL/Liu PWB unit QCNCM2548SC1B Connector(12pin) [CNLIUA] QJAKZ2060SC0B Jack [CNLNJ] QJAKZ2060SC0B Jack [CNTLJ] VHDDSS133//-1 Diode(1SS133) [D1] VHDDSS133//-1 Diode(1SS133) [D4] QSW-Z2263XHZZ Hook switch [HOOK SW] VHINJM2904M-2 IC(NJM2904M) [IC101] VHINJM2904M-2 IC(NJM2904M) [IC102] RFILN2027XHZZ Coil(R-5C) [L3A]...
  • Page 74 UX-8TH/UX-40TH GQ-5TH/FO-50TH PRICE PART DESCRIPTION PARTS CODE RANK MARK RANK [9] Power supply PWB unit 0CBUBC0336AZ/ Diode(S3L20U-4004P15) [D7] 0CBUBC0302BZ/ Diode(SR140) [D8] 0CBPJCEJ1601/ Current fuse(21501.6 ME600) [F1] 0CBPJCEJ1601/ Current fuse(21501.6 ME600) [F2] 0CBPZZ0906ZZ/ Circuit protect chip(CCP2E100) [F3] 0CBBFZ89256Z/ Beads core(BL02RNI-R62T4) [FB1] 0CBUCB0199AZ/ IC(UPC29M05AHF) [IC1]...
  • Page 75 UX-8TH/UX-40TH GQ-5TH/FO-50TH I n d e x PRICE PART PRICE PART PRICE PART PARTS CODE PARTS CODE PARTS CODE MARK MARK MARK RANK RANK RANK RANK RANK RANK MSPRC2735XHZZ RCILZ2145XHZZ 7-110 ″ CCNW-212AXH01 MSPRC2954XHZZ 7-111 ″ ″ MSPRC3110XHZZ 5-10 7-112 ″...
  • Page 76 UX-8TH/UX-40TH GQ-5TH/FO-50TH PRICE PART PRICE PART PRICE PART PARTS CODE PARTS CODE PARTS CODE RANK MARK RANK RANK MARK RANK RANK MARK RANK VCEAGA1HW226M VHD1SS355//-1 7-95 VRS-TS2AD271J 7-183 ″ ″ 7-96 VRS-TS2AD3R0J 7-126 ″ ″ 7-98 VRS-TS2AD303J 7-166 ″ VHEHZ27-1//-1 8-79 VRS-TS2AD332J 8-57...
  • Page 77 UX-8TH/UX-40TH GQ-5TH/FO-50TH PRICE PART PRICE PART PRICE PART PARTS CODE PARTS CODE PARTS CODE MARK MARK MARK RANK RANK RANK RANK RANK RANK 0CBUBXAD6R2C/ 9-72 0CBUBY0020AK/ 9-22 0CBUCB0199AZ/ 9-29 0CBUDA0128AK/ 9-38 0CBUDC0163CZ/ 9-35 ″ 9-36 0CBUDC0232AK/ 9-66 0CBUEEC105CH/ 9-44 ″ 9-45 0CBUEEC335CH/ 9-43...
  • Page 78 UX-8TH/UX-40TH GQ-5TH/FO-50TH © COPYRIGHT 1999 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.

This manual is also suitable for:

Gq-5Fo-50Ux-40

Table of Contents