Table of Contents
Advertisement
INSTALLATION INSTRUCTIONS
HB0092
MODELS BC2130SS & BC4130SS
INTENDED FOR DOMESTIC COOKING ONLY
!
!
READ AND SAVE THESE INSTRUCTIONS
INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER.
HOMEOWNER: USE AND CARE INFORMATION ON PAGES 10 AND 11.
Broan-NuTone Canada Inc.; Mississauga, Ontario www.broan.ca
877-896-1119
www.broan.ca
REGISTER YOUR PRODUCT ON LINE AT: www.broan.com/register
SV08969 rev. 05
Advertisement
Table of Contents
Related Manuals for Broan BC2130SS
Summary of Contents for Broan BC2130SS
- Page 1 INTENDED FOR DOMESTIC COOKING ONLY READ AND SAVE THESE INSTRUCTIONS INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER. HOMEOWNER: USE AND CARE INFORMATION ON PAGES 10 AND 11. Broan-NuTone Canada Inc.; Mississauga, Ontario www.broan.ca 877-896-1119 www.broan.ca REGISTER YOUR PRODUCT ON LINE AT: www.broan.com/register SV08969 rev. 05...
-
Page 2: To Reduce The Risk Of Fire, Electric Shock Or Injury To Persons, Observe The Following
9. To reduce the risk of fire and electrical shock, the Broan power pack models BC2130SS d) Use proper pan size. Always use cookware appropriate BC4130SS must be installed only with their own for the size of the surface element. built-in blower(s). Other blowers cannot be substituted. - Page 3 - BC2130SS & BC4130SS POWER PACK SYSTEM - TANDARD TANDARD 3¼” 10” W 3¼” 10” R NOT INCLUDED NOT INCLUDED TANDARD 3¼” 10” D NOT INCLUDED 3¼” 10” DAPTER AMPER INCLUDED BC4130SS BC2130SS POWER PACK POWER PACK HL0133 - 3 -...
-
Page 4: Prepare The Installation
1. PREPARE THE INSTALLATION WARNING When performing installation, servicing or cleaning the unit, it is recommended to wear safety glasses and gloves. NOTE: Before proceeding to the installation, check the contents of the box. If items are missing or damaged, contact the manufacturer. -
Page 5: Custom Hood Preparation
Failure to do so may cause personal injury or damage to countertop or cooktop. TOP VIEW The custom hood must be constructed to fit the shape and total weight of the BC2130SS or BC4130SS power pack models. See chart and illustrations for details. OTAL 5/16”... - Page 6 6. REMOVE THE ADAPTER/DAMPER Using a Phillips no. 2 screwdriver, remove both screws retaining the adapter/damper (A) to the power pack inner panel. Set the adapter/damper aside. NOTE: Though picture at right shows a double blower model, this applies also for single blower model.
-
Page 7: Install The Adapter/Damper
10. REMOVE THE ELECTRICAL KNOCK-OUT INGLE LOWER INGLE LOWER LOWER Punch out the electrical knockout hole on back (A) OR on top (B), to the right side of the power pack. Install the wire clamp (included in parts bag). LOWER Punch out the electrical knockout hole on top (B) OR in front (C) of the power pack. -
Page 8: Connect Wiring
13. CONNECT WIRING WARNING Risk of electric shock. Electrical wiring must be done by qualified personnel in accordance with all applicable codes and standards. Before connecting wires, switch power off at service panel and lock service disconnecting means to prevent power from being switched on accidentally. Position the power pack below the installed custom hood. - Page 9 15. INSTALL THE ADAPTER/DAMPER ON BACK OF POWER PACK (HORIZONTAL DISCHARGE INSTALLATION ONLY) From the outside of the wall, using 2 no. 8 x 3/8’’ screws provided in parts bag, secure the adapter/damper to the back of the power pack. Remove tape from damper flap.
-
Page 10: Light Bulbs
18. REINSTALL FILTER CAUTION Remove protective plastic film covering filter before installing it. Rest rear filter edge on filter springs (A) in the power pack. Using the finger cup, tilt up the filter into position. Make sure filter tabs (B) are securely engaged in power pack front edge after installation. -
Page 11: Operation
EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. During this one-year period, Broan-NuTone will, at its option, repair or replace, without charge, any product or part which is found to be defective under normal use and service. -
Page 12: Service Parts
RANSFORMER good working condition, you must use SV18407 INGLE LOWER EFLECTOR Broan-NuTone genuine replacement SV18408 LOWER EFLECTOR parts only. Broan-NuTone genuine SV01766 OTOR replacement parts are specially designed SV03400 LOWER HEEL for each unit and are manufactured to SV08965 QUARE...