Din Front/Rear-Mount; Removing The Unit - Pioneer Super Tuner IIID DEH-P5000UB Operation Manual

(~I "_s_t_a_lIa_t_io_"
)
(~
E------,,"g=--I_i s _h)
3. Install the unit as illustrated.
Removing the Unit
1. Extend top and bottom of the trim
ring outwards to remove the trim
ring. When reattaching the trim ring,
push the trim ring onto the unit until
it clicks. (If the trim ring is attached
upside down, the trim ring will not
fit properly.)
• It becomes easy to remove the trim ring if the
front panel is released.
DIN Front-mount
• Check all connections and systems before final in-
sta Ilation.
• Do not use unauthorized parts. The use of unau-
thorized parts may cause malfunctions.
• Consult with your dealer if installation requires drill-
ing of holes or other modifications of the vehicle.
• Do not install this unit where:
- it may interfere with operation of the vehicle.
- it may cause injury to a passenger as a result
of a sudden stop.
• The semiconductor laser will be damaged if it over-
heats. Install this unit away from hot places such as
nea r the heater outlet.
• Optimum performance is obtained when the unit is
installed at an angle of less than 60°.
DIN Front/Rear-mount
This unit can be properly installed either from
"Front" (conventional DIN Front-mount) or
"Rear" (DIN Rear-mount installation, utilizing
threaded screw holes at the sides of unit
chassis). For details, refer to the following
installation methods.
Installation with the rubber bush
1. Insert the mounting sleeve into the
dashboard.
• When installing in a shallow space. use a
supplied mounting sleeve. If there is enough
space behind the unit. use factory supplied
mounting sleeve.
2. Secure the mounting sleeve by
using a screwdriver to bend the
metal tabs (90°) into place.
2. Insert the supplied extraction keys
into both sides of the unit until they
cI
ick into place.
3. Pull the unit out of the dashboard.
(~I "_s_t_a_lIa_t_io_"
)
(~
E------,,"g=--I_i s _h)
3. Install the unit as illustrated.
Removing the Unit
1. Extend top and bottom of the trim
ring outwards to remove the trim
ring. When reattaching the trim ring,
push the trim ring onto the unit until
it clicks. (If the trim ring is attached
upside down, the trim ring will not
fit properly.)
• It becomes easy to remove the trim ring if the
front panel is released.
DIN Front-mount
• Check all connections and systems before final in-
sta Ilation.
• Do not use unauthorized parts. The use of unau-
thorized parts may cause malfunctions.
• Consult with your dealer if installation requires drill-
ing of holes or other modifications of the vehicle.
• Do not install this unit where:
- it may interfere with operation of the vehicle.
- it may cause injury to a passenger as a result
of a sudden stop.
• The semiconductor laser will be damaged if it over-
heats. Install this unit away from hot places such as
nea r the heater outlet.
• Optimum performance is obtained when the unit is
installed at an angle of less than 60°.
DIN Front/Rear-mount
This unit can be properly installed either from
"Front" (conventional DIN Front-mount) or
"Rear" (DIN Rear-mount installation, utilizing
threaded screw holes at the sides of unit
chassis). For details, refer to the following
installation methods.
Installation with the rubber bush
1. Insert the mounting sleeve into the
dashboard.
• When installing in a shallow space. use a
supplied mounting sleeve. If there is enough
space behind the unit. use factory supplied
mounting sleeve.
2. Secure the mounting sleeve by
using a screwdriver to bend the
metal tabs (90°) into place.
2. Insert the supplied extraction keys
into both sides of the unit until they
cI
ick into place.
3. Pull the unit out of the dashboard.