Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Rocktron Bass 200
Summary of Contents for Rocktron Bass 200
- Page 1 200 Watt Bass Amplifier Instruction Manual May be covered by one or more of the following: U.S. Patents #4538297, 4647876, 4696044, 4745309, 4881047, 4893099, 5124657, 5263091, 5268527, 5319713, 5333201, 5402498 and 5493617. Other patents pending. Foreign patents pending.
- Page 2 Your Rocktron Bass200 Bass Amplifier has been tested and complies with the following Standards and Directives as set forth by the European Union: Standard(s): IEC60065 Professional Audio/Video or Similar Equipment, EN55013:1997, EN61000-3-2 (1995) EN61000-3-3(1995), EN55020:1995, CSA E65-94 This means that this product has been designed to meet stringent guidelines on how much RF energy it can emit, and that it should be immune from other sources of interference when properly used.
-
Page 3: Operating Temperature
PRECAUTIONS NOTE: IT IS VERY IMPORTANT THAT YOU READ THIS SECTION TO PROVIDE YEARS OF TROUBLE FREE USE. THIS UNIT REQUIRES CAREFUL HANDLING. • All warnings on this equipment and in the operating instructions should be adhered to and all operating instructions should be followed. •... -
Page 4: Grounding Instructions
WARNING: To reduce the risk of fire or electric shock, do not expose this unit to rain or moisture. The lightning flash with an arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of un-insulated “dangerous voltage” within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock. - Page 5 Introduction Congratulations on your purchase of the Rocktron Bass200 amplifier! You will feel the low-end power and thump on this gig ready amp. We have included many features into the Bass200: High and Low Inputs Gain and Master Volume Controls with clip indicating LEDs...
-
Page 6: Front Panel
Front Panel HIGH Input Jack Using a standard guitar cable with a 1/4” jack - plug your bass into this jack. This input jack was designed for passive basses (without batteries), however, you may plug your active bass into this input for a higher gain structure. LOW Input Jack Using a standard guitar cable with a 1/4”... -
Page 7: Volume Control
BASS Control This control provides a 15dB of cut or boost at 100Hz. Rotating this control clockwise will increase the lower frequencies and, depending on other settings, will generally make your tone warmer and heavier. MID-LOW Control This control provides approximately 15dB of cut or boost at 220Hz. MID (MIDDLE) Control This control allows your getting 15dB of cut or boost at 660Hz. -
Page 8: Back Panel
Back Panel AC POWER CORD Using the included power cable connect the amplifier to a standard wall outlet. See “Fuse Replacement” section for details on how to replace the fuse. SPEAKER OUTPUT Jack The socket is situated on the rear panel of the unit. It connects to the in- ternal speaker, you can also connect it to an external speaker cabinet. -
Page 9: Fuse Replacement
Fuse Replacement We recommend that you use an authorized repair person to change the fuse in this unit. To access the fuse, first power down the unit and unplug the cable from the wall outlet and the amplifier. Using a small screw driver, open the fuse tray by prying open the small tab as shown in the drawing above. -
Page 10: General Specifications
Specifications INPUTS High Input Impedance 3.9M Ohms Input range 150mV to 20V p-p Low Input Impedance 10K Ohms Input range 300mV to 40V p-p Effects Return Impedance 4.7K Ohms OUTPUTS Effects Send Impedance 4.7K Ohms Line Out Impedance 22K Ohms Speaker Outputs Min. - Page 12 Rocktron - A Division of GHS Corporation 2813 Wilber Ave. Battle Creek MI 49037 Tel: 1-269-968-3351 Fax: 1-249-968-6913 (8am to 5pm Eastern Standard Time) www.rocktron.com Rev. 12/26/07...