Husqvarna 326C Operator's Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Trimmer
  5. 326C, 326L, 326LX-Series, 326LDX-Series
  6. Operator's manual
Husqvarna 326C Operator's Manual

Husqvarna 326C Operator's Manual

Trimmers
Hide thumbs Also See for 326C:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Owner's Manual, Operator's Manual
Operator's manual (EPA)
326C 326L 326L
X-SERIES
326LD
X-SERIES
Please read the operator's manual carefully and make sure you
E E E E n n n n g g g g l l l l i i i i s s s s h h h h
understand the instructions before using the machine.

Advertisement

Table of Contents
loading

Related Manuals for Husqvarna 326C

Summary of Contents for Husqvarna 326C

  • Page 1 Operator’s manual (EPA) 326C 326L 326L X-SERIES 326LD X-SERIES Please read the operator’s manual carefully and make sure you E E E E n n n n g g g g l l l l i i i i s s s s h h h h...

  • Page 2: Key To Symbols

    KEY TO SYMBOLS Symbols Only intended for trimmer heads. WARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. Please read the operator’s manual carefully Other symbols/decals on the machine and make sure you understand the refer to special certification requirements for certain...

  • Page 3: Table Of Contents

    CONTENTS Contents Note the following before starting: KEY TO SYMBOLS Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the Symbols ............... design and appearance of products without prior notice. CONTENTS Contents ..............

  • Page 4: Safety Instructions

    SAFETY INSTRUCTIONS Personal protective equipment Machine ′ ′ ′ ′ s safety equipment This section describes the machine ′ s safety equipment, its IMPORTANT! You must use approved personal protective purpose, and how checks and maintenance should be carried equipment whenever you use the machine. Personal out to ensure that it operates correctly.

  • Page 5: Cutting Equipment

    SAFETY INSTRUCTIONS Vibration damping system For mufflers it is very important that you follow the instructions on checking, maintaining and servicing your machine. See Your machine is equipped with a vibration damping system instructions under the heading Checking, maintaining and that is designed to minimize vibration and make operation servicing the machine’s safety equipment.

  • Page 6: Checking, Maintaining And Servicing The Machine ' S Safety Equipment

    SAFETY INSTRUCTIONS Checking, maintaining and servicing Cutting attachment guard the machine ′ ′ ′ ′ s safety equipment IMPORTANT! All servicing and repair work on the machine • Ensure that the guard is undamaged and is not cracked. requires special training. This is especially true of the machine ′...

  • Page 7: Cutting Equipment

    SAFETY INSTRUCTIONS • If the muffler on your machine is fitted with a spark WARNING! Never use a machine with faulty arrestor mesh then it should be cleaned regularly. A safety equipment. The machine’s safety blocked mesh causes the engine to overheat, which can equipment must be checked and maintained lead to serious damage.

  • Page 8: General Safety Precautions

    SAFETY INSTRUCTIONS General safety precautions (CAUTION! Not with your foot). Then grip the starter handle with your right hand and pull the starter cord. Never wrap the starter cord around your hand IMPORTANT! The machine is only designed for trimming grass. The only accessories you can operate with this engine unit are the cutting attachments we recommend in the chapter on Technical data.

  • Page 9: General Working Instructions

    SAFETY INSTRUCTIONS Basic working techniques • The transport guard must always be fitted to the cutting attachment when the machine is being transported or in storage. • Always slow the engine to idle speed after each working operation. Long periods at full throttle without any load on the engine can lead to serious engine damage.
  • Page 10 SAFETY INSTRUCTIONS Cutting • The trimmer is ideal for cutting grass that is difficult to reach using a normal lawn mower. Keep the cord parallel to the ground when cutting. Avoid pressing the trimmer head against the ground as this can ruin the lawn and damage the tool.

  • Page 11: What Is What

    WHAT IS WHAT? What is what? 1 Trimmer head 13 Choke control 2 Grease filler cap, bevel gear 14 Air purge 3 Bevel gear 15 Air filter cover 4 Cutting attachment guard 16 Handle adjustment 5 Shaft 17 Locking nut 6 Loop handle 18 Support flange 7 Throttle control...

  • Page 12: Assembly

    • Align the cut-out in the lower part of the shaft with the coupling locking tab on the upper part of the shaft. Then lock the sections together. (326C) • Tighten the knob. • Position the handle on the shaft. Note that the handle must be mounted below the arrow on the shaft.

  • Page 13: Fitting A Trimmer Guard And Superauto Ii 1" Trimmer Head

    Fitting the trimmer guard and kit. Hold the shaft of the spanner as close to the blade trimmer head guard as possible. (326C) To tighten the nut, turn the spanner in the opposite direction to the direction of rotation (Caution! left-hand thread).

  • Page 14: Fuel Handling

    Fuel Two-stroke oil • For best results and performance use HUSQVARNA two- CAUTION! The machine is equipped with a two-stroke engine stroke oil, which is specially formulated for our two-stroke and must always been run using a mixture of gasoline and engines.

  • Page 15: Fuelling

    FUEL HANDLING Fuelling WARNING! Taking the following precautions, will lessen the risk of fire: Do not smoke or place hot objects near fuel. Always shut off the engine before refuelling. Always stop the engine and let it cool for a few minutes before refuelling.

  • Page 16: Starting And Stopping

    STARTING AND STOPPING Check before starting Starting and stopping • Check that the support flange is not cracked due to fatigue or due to being tightened too much. Discard the support WARNING! The complete clutch cover and flange if it is cracked. shaft must be fitted before the machine is started, otherwise the clutch can come loose and cause personal injury.
  • Page 17 STARTING AND STOPPING some resistance (the starter pawls grip), now quickly and powerfully pull the cord. Never wrap the starter cord around your hand Repeat pulling the cord until the engine starts. When the engine starts. return choke control to run position and apply full throttle;...

  • Page 18: Maintenance

    CAUTION! If the cutting attachment rotates when the engine is idling the idle adjustment screw T should be turned anti- clockwise until the cutting attachment stops. Your Husqvarna product has been designed and manufactured to specifications that reduce harmful Rec. idle speed 2700 rpm emissions.

  • Page 19: Muffler

    MAINTENANCE Correctly adjusted carburettor will run smoothly in every position. The idle speed should also be well below the speed at which the cutting attachment starts When the carburettor is correctly adjusted the machine will to rotate. accelerate without hesitation and burble a little at maximum speed.

  • Page 20: Cooling System

    MAINTENANCE Cooling system Shaft To keep the working temperature as low as possible the The drive shaft end in the lower shaft should be lubricated machine is equipped with a cooling system. with grease every 30 hours. There is a risk that the drive shaft ends (splined coupling) on models with two-piece shafts will seize if they are not lubricated regularly.

  • Page 21: Maintenance Schedule

    • A non-balanced blade/trimmer head induces heavy vibrations that may damage the machine. Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The filter oil contains a solvent to make it spread evenly through • Check that nuts and screws are tight.

  • Page 22: Technical Data

    TECHNICAL DATA Technical data 326C 326L 326Lx/326LDx Engine Cylinder volume, cu.in/cm 1,50/24,5 1,50/24,5 1,50/24,5 Cylinder bore, inch/mm 1,34/34,0 1,34/34,0 1,34/34,0 Stroke, inch/mm 1,06/27 1,06/27 1,06/27 Idle speed, rpm 2700 2700 2700 Recommended max. speed, rpm 11000-11700 11000-11700 11000-11700 Speed of output shaft, rpm...
  • Page 23 TECHNICAL DATA Approved accessories Type Cutting attachment guard, Art. no. 326C Blade shaft thread 3/8 R Plastic blades Tricut Ø 230 mm (R) 537 02 61-01 / 537 07 67-01 Trimmer head Trimmy Hit VI (R) 537 02 61-01 / 537 07 67-01...

  • Page 24: Federal Emission Control Warranty Statement

    Forest & Garden cannot deny warranty solely for the lack of responsibilities, you should contact your nearest authorized receipts or for your failure to ensure the performance of all servicing dealer or call Husqvarna Forest & Garden at 1-800- scheduled maintenance. As the small nonroad engine owner, 487-5963.
  • Page 25 Super Auto II Super Auto II 1 " 4,0 m 15 cm ~2,0 m 6 " 6,5 ' 15 cm 6 "...
  • Page 27 Trimmy H II 15 cm 6" 7,5 m ~ 3,7 m 15 cm 6"...
  • Page 28 Trimmy Hit “Click” 7,0 m 12 cm 5" ~ 3,5 m “Click” ~ 15 cm " 15 cm 6 "...
  • Page 29 Trimmy Hit Pro 7,5 m 15 cm 6" ~ 3,7 m 15 cm 6" 15 cm “Click” 6"...
  • Page 30 8,5 m 10 cm 4" 4,2 m "Clic" 15 cm 6"...
  • Page 31 4,25 m 4,25 m 15 cm 6" 15 cm 6"...
  • Page 32 8,5 m 10 cm 4" 4,3 m "Clic" 15 cm 6"...
  • Page 33 Trimmy VII 7,0 m 23" 12 cm 5" ~ 3,5 m 11" ~ 15 cm 6" 15 cm 6"...
  • Page 34 ´®z+H;3¶5Q¨ ´®z+H;3¶5Q¨...
  • Page 36 1140271-95 ´®z+H;3¶5Q¨ ´®z+H;3¶5Q¨ 2004-03-23...

This manual is also suitable for:

326lx-series326ldx series326lx series326l

Table of Contents