1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Trimmer
  5. 326HD60 X-series
  6. Operator's manual

Husqvarna 326HD60 X-series Operator's Manual

Cutter
Hide thumbs Also See for 326HD60 X-series:
Table of Contents

Advertisement

Quick Links

Operator's manual (CARB II, EPA II)
326HD60
326HD75
Please read the operator's manual carefully and make sure you
understand the instructions before using the machine.
X-series
X-series
E E E E n n n n g g g g l l l l i i i i s s s s h h h h

Advertisement

Table of Contents
loading

Related Manuals for Husqvarna 326HD60 X-series

Summary of Contents for Husqvarna 326HD60 X-series

  • Page 1 Operator’s manual (CARB II, EPA II) 326HD60 X-series 326HD75 X-series Please read the operator’s manual carefully and make sure you E E E E n n n n g g g g l l l l i i i i s s s s h h h h understand the instructions before using the machine.

  • Page 2: Key To Symbols

    KEY TO SYMBOLS Symbols WARNING! Incorrect or careless use of a hedge trimmer can turn it into a dangerous tool that can cause serious or even fatal injury. It is extremely important that you read and understand the contents of this operator’s manual.

  • Page 3: Table Of Contents

    CONTENTS Contents Note the following before starting: KEY TO SYMBOLS Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the Symbols ............... design and appearance of products without prior notice. CONTENTS Contents ..............

  • Page 4: Safety Instructions

    SAFETY INSTRUCTIONS Personal protective equipment FIRST AID KIT Always have a first aid kit nearby. IMPORTANT! Incorrect or careless use of a hedge trimmer can turn it into a dangerous tool that can cause serious or even fatal injury. It is extremely important that you read and understand the contents of this operator’s manual.
  • Page 5 SAFETY INSTRUCTIONS Vibration damping system WARNING! The inside of muffler contain chemicals that may be carcinogenic. Avoid Your machine is equipped with a vibration damping system contact with these elements in the event of a that is designed to minimise vibration and make operation damaged muffler.

  • Page 6: Checking, Maintaining And Servicing The Machine S Safety Equipment

    SAFETY INSTRUCTIONS Checking, maintaining and servicing • See instructions under the heading Start. Start the hedge trimmer and apply full throttle. Release the throttle trigger the machine s safety equipment and check that the blades stop and remain stationary. If the blades move when the throttle trigger is in the idle position then the carburettor idle setting must be adjusted.

  • Page 7: Gear Housing

    SAFETY INSTRUCTIONS Muffler Blade guard • Never use a machine that has a faulty muffler. • Check that the blade guard is not damaged or distorted. • Replace the blade guard if it is bent or damaged. • Regularly check that the muffler is securely attached to the machine.

  • Page 8: General Safety Precautions

    SAFETY INSTRUCTIONS General safety precautions Fuel safety IMPORTANT! The machine is only designed for cutting branches and twigs. • Always use a fuel container with an anti-spill valve. Never use the machine if you are tired, if you have drunk •...

  • Page 9: Safety Instructions When Using The Hedge Trimmer

    SAFETY INSTRUCTIONS Safety instructions when using the Safety instructions while working hedge trimmer WARNING! The machine can cause serious • Always ensure you have a safe and stable working personal injury. Read the safety instructions position carefully. Learn how to use the machine. •...

  • Page 10: Basic Working Techniques

    SAFETY INSTRUCTIONS Safety instructions after completing work • The transport guard should always be fitted to the cutting attachment when the machine is not in use. • Make sure the cutting attachment has stopped before cleaning, carrying out repairs or an inspection. Disconnect the HT lead from the spark plug.

  • Page 11: What Is What

    WHAT IS WHAT? What is what? 1 Operator’s manual (EPA) 13 Lock for handle 2 Grease filler cap 14 Fuel tank 3 Gear housing 15 Fuel cap 4 Blades 16 Air purge 5 Blade guard 17 Choke control 6 Front handle 18 Air filter cover.

  • Page 12: Fuel Handling

    Always stop the engine and let it cool for a few minutes before refuelling. • For best results and performance use HUSQVARNA two- stroke oil, which is specially formulated for our two-stroke When refuelling, open the fuel cap slowly so engines.

  • Page 13: Starting And Stopping

    STARTING AND STOPPING Check before starting Starting and stopping Starting • Inspect the working area. Remove any objects that could be thrown out. • Check the cutting attachment. Never use blades that are dull, cracked or damaged. WARNING! The gear housing and clutch drum must be fitted before the machine is started, otherwise the clutch can come loose and cause personal injury.

  • Page 14: Warm Engine

    STARTING AND STOPPING Warm engine Stopping Ignition: Set the stop switch to the start position. The engine is stopped by switching the ignition off using the stop switch. Choke: Set the choke control in the choke position and then back to its original position. This only engages the start throttle setting without any choke.

  • Page 15: Maintenance

    Basic setting • The basic carburettor settings are adjusted during testing Your Husqvarna product has been designed and at the factory. The basic setting is richer than the optimal manufactured to specifications that reduce harmful setting and should be maintained for the first few hours the emissions.

  • Page 16: Muffler

    MAINTENANCE Fine adjustment of the idle speed T Correctly adjusted carburettor Adjust the idle speed with the idle adjustment screw T, if When the carburettor is correctly adjusted the machine adjustment is necessary. First turn the idle adjustment screw accelerates without hesitation and burbles a little at maximum T clockwise until the blades start to move.

  • Page 17: Cooling System

    See instructions under the heading Oiling the air filter. Oiling the air filter Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The The cooling system consists of: filter oil contains a solvent to make it spread evenly through the filter.

  • Page 18: Gear Housing

    There is a grease nipple on the gearbox. Use a grease gun to correctly tightened. top up with grease. This should be carried out after approximately every 20 working hours. Use Husqvarna • Check that the transport guard for the blade is intact and special grease, No.

  • Page 19: Technical Data

    TECHNICAL DATA Technical data Technical data 326HD60 326HD75 Engine Cylinder volume, cu.in/cm 1,55/25,4 1,55/25,4 Cylinder bore, inch/mm 1,34/34 1,34/34 Stroke, inch/mm 1,10/28 1,10/28 Idle speed, rpm 2700 2700 Recommended max. speed, rpm 11000-11700 11000-11700 Max. engine output, acc. to ISO 8893 0,9/9000 0,9/9000 Catalytic converter muffler...

  • Page 20: Federal Emission Control Warranty Statement

    Husqvarna servicing dealer or call Husqvarna Forest & Garden at 1-800- Forest & Garden cannot deny warranty solely for the lack of 487-5963 receipts or for your failure to ensure the performance of all scheduled maintenance.
  • Page 22 ´®z+H7)¶5h¨ ´®z+H7)¶5h¨...
  • Page 24 1140230-95 ´®z+H7)¶5h¨ ´®z+H7)¶5h¨ 2003-09-25...

This manual is also suitable for:

326hd75 x-series

Table of Contents