Husqvarna 323LD Operator's Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Trimmer
  5. 323LD
  6. Operator's manual

Husqvarna 323LD Operator's Manual

Husqvarna trimmer operator's manual
Hide thumbs Also See for 323LD:
Table of Contents

Advertisement

Quick Links

Oper ator ' s manual
323L 323LD 325CX
325LX 325LDX
Please r ead the operator's manual carefully and make sure you
E E E E n n n n g g g g l l l l i i i i s s s s h h h h
understand the instructions before using the machine.

Advertisement

Table of Contents
loading

Related Manuals for Husqvarna 323LD

Summary of Contents for Husqvarna 323LD

  • Page 1 Oper ator ′ s manual 323L 323LD 325CX 325LX 325LDX Please r ead the operator’s manual carefully and make sure you E E E E n n n n g g g g l l l l i i i i s s s s h h h h...

  • Page 2: Key To Symbols

    Arro ws which show limits for handle positioning. Alw ays wear approved protective gloves. W ear sturdy, non-slip boots. Only use non-metallic , flexible cutting attachments, i.e. trimmer heads with trimmer cord. 2 – English KEY T O SYMBOLS Only intended f or trimmer heads.

  • Page 3: Table Of Contents

    Fitting the loop handle ... Assembling and dismantling the two-piece shaft ... Fitting the trimmer head ... Fitting a trimmer guard and Superauto II 1” trimmer head ... Fitting other guards and cutting attachments ... Fitting the trimmer guard and trimmer head ...

  • Page 4: Intr Oduction

    Dear Customer , Cong ratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Charles XI ordered the construction of a factory on the banks of the Husqvarna River, for production of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the water-powered plant.

  • Page 5: What Is What

    What is what? 1 Trimmer head 2 Grease filler cap, bevel gear 3 Bevel gear 4 Cutting attachment guard 5 Shaft 6 Loop handle 7 Throttle control 8 Stop switch 9 Throttle lock 10 Cylinder cover 11 Starter handle 12 Fuel tank...

  • Page 6: General Safety Preca Utions

    English Personal protective equipment IMPOR TANT! A clearing saw, brushcutter or trimmer can be dangerous if used incorrectly or carelessly, and can cause serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of this operator’s manual.

  • Page 7: Machine ' S Safety Equipment

    GENERAL SAFETY PRECA UTIONS FIRST AID KIT Alw ays have a first aid kit nearby. Mac hine ′ ′ ′ ′ s safety equipment This section descr ibes the machine ′ s safety equipment, its purpose, and how checks and maintenance should be carried out to ensure that it operates correctly.
  • Page 8 GENERAL SAFETY PRECAUTIONS Cutting attachment guard This guard is intended to prevent loose objects from being thrown towards the operator. The guard also protects the operator from accidental contact with the cutting attachment. Check that the guard is undamaged and not cracked. Replace the guard if it has been exposed to impact or is cracked.

  • Page 9: Cutting Equipment

    • Make sure that the cutter on the trimmer guard is intact. This is used to cut the cord to the correct length. • To increase the life of the cord it can be soaked in water for a couple of days.

  • Page 10: Assembly

    fitted between the arrows on the shaft. • Slide the spacer into the slot in the loop handle. • 323L/323LD: Fit the nut, washer and screw. 325Lx/325LDx: Fit the nut, knob and screw. Do not overtighten. •...

  • Page 11: Fitting The Trimmer Head

    (Caution! left-hand thread). • Fit the bottom half of the trimmer head (K) to the cover (I) by pressing them together, with the cut-outs on the bottom half aligned with the catches on the cover.

  • Page 12: Fitting The Trimmer Guard And Trimmer Head

    Fit the dust cup on the shaft. The nut must be completely covered by the dust cup. • Hold the dust cup with a spanner to prevent the shaft from rotating. • Screw the trimmer head onto the shaft. 12 – English ASSEMBLY...

  • Page 13: Fuel Handling

    When working at continuous high revs a higher octane rating is recommended. Two-stroke oil • For best results and performance use HUSQVARNA two- stroke engine oil, which is specially formulated for our air- cooled two-stroke engines. • Never use two-stroke oil intended for water-cooled engines, sometimes referred to as outboard oil (rated TCW).

  • Page 14: Fuelling

    Mixing • Always mix the petrol and oil in a clean container intended for fuel. • Always start by filling half the amount of the petrol to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of petrol. •...

  • Page 15: Starting And Stopping

    • Check that the trimmer head and trimmer guard are not damaged or cracked. Replace the trimmer head or trimmer guard if they have been exposed to impact or are cracked. • Never use the machine without a guard nor with a defective guard.
  • Page 16 STARTING AND STOPPING CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended. This can damage the machine. CAUTION! Do not put any part of your body in marked area. Contact can result in burns to the skin, or electrical shock if the spark plug cap has been damaged.

  • Page 17: Working Techniques

    General working instructions IMPORTANT! This section takes up the basic safety precautions for working with a trimmer. If you encounter a situation where you are uncertain how to proceed you should ask an expert. Contact your dealer or your service workshop.

  • Page 18: Grass Trimming With A Trimmer Head

    Clearing • The clearing technique removes all unwanted vegetation. Keep the trimmer head just above the ground and tilt it. Let the end of the cord strike the ground around trees, posts, statues and the like. CAUTION! This technique increases the wear on the cord.

  • Page 19: Maintenance

    Carburettor Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in. To ensure that it continues to run at peak performance and to minimise harmful exhaust emissions...

  • Page 20: Muffler

    Fine adjustment of the idle speed T Adjust the idle speed using the idle adjustment screw T, if it is necessary to readjust. First turn the idle adjustment screw T clockwise until the cutting attachment starts to rotate. Then turn the screw anticlockwise until the cutting attachment stops.

  • Page 21: Cooling System

    Check that the spark plug is fitted with a suppressor. MAINTENANCE Two-piece shaft (323LD, 325LDx) The drive shaft end in the lower shaft should be lubricated with grease every 30 hours. There is a risk that the drive shaft ends (splined coupling) on models with two-piece shafts will seize if they are not lubricated regularly.

  • Page 22: Bevel Gear

    MAINTENANCE Oiling the air filter Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The filter oil contains a solvent to make it spread evenly through the filter. You should therefore avoid skin contact. Put the filter in a plastic bag and pour the filter oil over it.

  • Page 23: Maintenance Schedule

    Check that the guard is undamaged and not cracked. Replace the guard if it has been exposed to impact or is cracked. Check that the trimmer head is undamaged and not cracked. Replace the trimmer head if necessary. Check that the locking nut of the cutting equipment is tighten correctly.

  • Page 24: Technical D Atat Echnical Data

    NOTE! The noise pressure level at operator’s ear and vibrations on the handles are measured with all the approved cutting attachments for the machine. The table indicates the lowest and highest values. 24 – English TECHNICAL DATA 323L 323LD 24,5 24,5 34,0 34,0 2700...
  • Page 25 Technical data Engine Cylinder displacement, cm Cylinder bore, mm Stroke, mm Idle speed, rpm Recommended max. fast idle speed, rpm Speed of output shaft, rpm Max. engine output, acc. to ISO 8893, kW/ rpm Catalytic converter muffler Speed-regulated ignition system Ignition system Manufacturer/type of ignition system Spark plug...

  • Page 26: Ec-Declaration Of Conformity (Applies To Europe Only)

    We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare that the clearing saws Husqvarna 323L, 323LD, 325Cx, 325Lx and 325LDx with serial numbers dating from 2002 onwards (the year is clearly stated on the rating plate, followed by the serial number), comply with the requirements of the COUNCIL’S DIRECTIVE: of June 22, 1998 ”relating to machinery”...
  • Page 27 Super Auto II Super Auto II 1 " 4,0 m 15 cm ~2,0 m 6 " 6,5 ' 15 cm 6 "...
  • Page 29 8,5 m 10 cm 4" 4,2 m "Clic" 15 cm 6"...
  • Page 30 4,25 m 4,25 m 15 cm 6" 15 cm 6"...
  • Page 31 15 cm 6" 8,5 m 10 cm 4" 4,3 m "Clic"...
  • Page 32 15 cm 6" 6,0 m 10 cm 4" 3,05 m "Clic"...
  • Page 33 T25C 2,75 m 2,75 m 15 cm 6"...
  • Page 34 T25C 15 cm 6" ´®z+R-T¶63¨ ´®z+R-T¶63¨ 2,75 m x 2 9' x 2 2,75 m 2,75 m "Clic"...
  • Page 36 1150135-26 ´®z+R-T¶63¨ ´®z+R-T¶63¨ 2005-10-25...

This manual is also suitable for:

323l325cx325lx325ldx326c326l ... Show all

Table of Contents