Majestic fireplaces CR36R Homeowner's Installation And Operating Manual

Cr series corner woodburning fireplace

Hide thumbs Also See for CR36R:

Homeowner's installation and operating manual (24 pages)

Table Of Contents

Quick Links

Download this manual

For use in U.S./Canada

Underwriter's Laboratories

Report No. MH6018

DO NOT DISCARD THIS MANUAL: Retain for future use.

CR Series

Corner Woodburning Fireplace

Homeowner's Installation

and Operating Manual

For Models:

CR36R

CR36L

20001316 4/07 Rev. 14

Table of Contents

Need help?

Do you have a question about the CR36R and is the answer not in the manual?

Questions and answers

Summary of Contents for Majestic fireplaces CR36R

Page 1 CR Series Corner Woodburning Fireplace Homeowner’s Installation and Operating Manual For Models: CR36R CR36L 36R, CR36L 99 djt For use in U.S./Canada Underwriter’s Laboratories Report No. MH6018 DO NOT DISCARD THIS MANUAL: Retain for future use. 20001316 4/07 Rev. 14...
Page 2: Table Of Contents
ﬁreplace surround. Description Burn only solid wood fuel or gas logs. The CR36R/L Series ﬁreplaces are multi-sided solid fuel, Do not install a solid fuel burning insert or other woodburning ﬁreplaces. These are radiant models only products not speciﬁed for use with this ﬁreplace.
Page 3: Speciﬁcations And Framing
36" (914mm) (203mm) Access (172mm) 40��" (1019mm) 7" 14��" (178mm) (362mm) (CR36R Shown) Fig. 1 CR36R/L Series speciﬁcations and framing. CR Specs 3/3/99 djt 25¹⁄₂" (648 mm) 25¹⁄₂" (648 mm) 15⁵⁄₈" 15⁵⁄₈" (397 mm) (397 mm) 32³⁄₈" (822 mm) 32³⁄₈" (822 mm)
Page 4: Parts Identiﬁcation
CR Series Woodburning Fireplaces Chase Installation Insulation methods shown are optional Termination Cap for cold climates, not a requirement for unit operation. Storm Collar Pan Flashing Batt Insulation (cut out around ﬁrestop) Draftstop Firestop Ceiling Level Outer Dome Finish Wall See Figure 20 on page 15 for clearance information Ledge Bracket...
Page 5: Chimney Requirements
CR Series Woodburning Fireplaces Chimney Requirements - Offset Installations OFFSET Chimney Flue Exit RISE Chimney Section FP282 IWF282 Elbow 30° 30˚ Elbow Offsets MBUF Return 5/26/96 Elbow 1’ 1¹⁄₂' 3’ 4’ Offset Rise 30° Offset 0 0 0 0 3” 11”...
Page 6: Planning Information
CR Series Woodburning Fireplaces Planning Information Preplanning an installation is very important to ensure The Ten Foot Rule safety and to save time and money. An installer must Major U.S. building codes specify a minimum chimney predetermine where a ﬁreplace will be set and how the height above the roof top.
Page 7: Installation
CR Series Woodburning Fireplaces Angled chimney runs require a support every 6’ (1.8 m) Installation in addition to the elbow straps. Chimney supports are used for this function. (Fig. 6) Insulating Fireplace Enclosure For Chase Installation Cold Climates A chase is a vertical box-like structure which encloses If you live in a cold climate, it is not required but the ﬁreplace and/or chimney.
Page 8 CR Series Woodburning Fireplaces Offset Installation Framing In order to clear an obstruction, it may be necessary Framing can be constructed before or after the ﬁreplace to offset chimney from vertical. This is accomplished is set in place, however, most installers build the frame by using CFM Corporation elbows.
Page 9 ¹⁄₂" (13mm) Plat- Members Min. Overlap Hearth Ext. form 1¹⁄₂" (38mm) 1¹⁄₂" (38mm) FPR557 FP551A Fig. 11 Safety strip installation. Fig. 10 Typical frame for ceiling chimney hole FPR557 CR36R,L 20001316 FP551a Safety strip installa CR36 Series 2/3/99 djt 2/22/99 djt...
Page 10 CR Series Woodburning Fireplaces Pipe Section Pipe Rim Lance Pipe Nail Top Standoffs STR100 Fig. 12 Fasten ﬁreplace in position. FP558CR STR100 standoffs, corner Installing the Chimney System Fig. 13 Install pipe, listening for the snap-lock to fasten. 2/18/99 djt Start by attaching the ﬁrst chimney section to the collar Support Structure on top of the ﬁreplace.
Page 11 CR Series Woodburning Fireplaces Hole sizes listed in Figure 10 for angled ﬁrestop spac- ers provide minimum required air space to chimney pipe for ceiling thickness up to 8” (203mm). When combined thickness of ceiling material, ceiling joists Attic Insulation and ﬂooring material exceeds 8”...
Page 12 CR Series Woodburning Fireplaces Check the chimney top installation instructions for Cut and Frame Roof Hole details on how high above the roof top the chimney Size of roof hole varies with the type of chimney sections (all pipes) should extend. termination installed.
Page 13 CR Series Woodburning Fireplaces Mantel Clearance - Mantel Clearance - No Noncombustible Facing Material with Noncombustible Facing Material Combustible 12" Combustible 12" Mantel and (305mm) Mantel and (305mm) Trim Finished Wall Finished Max. Trim Max. Wall Header Header 1¹⁄₂" 1¹⁄₂" Standoff Standoff 12"...
Page 14 CR Series Woodburning Fireplaces Hearth Installation Finish Wall Finish the wall with material of your choice. Do not A hearth extension is required to protect a combustible install a combustible mantel shelf less than 12” ﬂoor in front of the ﬁreplace. Refer to Figure 20 for mini- (305mm) from the top of the ﬁreplace opening.
Page 15 Combustible Model with SP40 Non-protected Wall Floor Min. wall covering distances 3/3/99 djt CR36L 12” 16” Safety Strips CR36R Minimum Must Overlap Insulation ¹⁄₂” Min. Value “R” Minimum Hearth Extension Dimensions FS107a Fig. 22 Hearth extension. 22” Min. Trim Molding...
Page 16 Majestic Fireplaces CR36R/L Series ﬁreplace is de- signed to accept a 1/2” gas line for an approved gas ap- pliance. (CFM Corporation manufactures a wide variety of gas logs for use in Majestic Fireplaces.) Have the Ceramic appliance installed by a qualiﬁed plumber in accordance or Metal with all building codes.
Page 17: Replacement Parts
CR Series Woodburning Fireplaces CFM Corporation reserves the right to make changes in design, materials, speciﬁcations, prices and discontinue colors and products at any time, without notice. CR36R/L Woodburning Fireplace Units: FG10R7, FG10R8 Parts page CR36L/R Ref. Description CR36L CR36R 3/17/99 djt 1.
Page 18: Accessories
CR Series Woodburning Fireplaces Accessories The following accessory parts can be obtained from Majestic Fireplaces Dealer. The fan kit, top terminations, outside air kit, glass doors and hearth patching kits are supplied with installation instructions packaged with the unit. Should you need additional information beyond what your dealer can furnish, contact CFM Corporation, 410 Admiral Blvd.
Page 19 CR Series Woodburning Fireplaces Accessory Description Model No. Chimney Support Used to support the chimney at each SKCS8 30 feet of vertical height above the (8” ﬂue) hearth and at every 6 feet of inclined chimney run. Each support adds 2¹⁄₂ inches to chimney length.
Page 20 CR Series Woodburning Fireplaces Accessory Model No. Description Contemporary Flashing Required for contemporary round top 8-6-12 termination on the roof to prevent (8” ﬂue; 0 to 6/12 pitch) rain entry. 8-12-12 (8” ﬂue; 6/12 to 12/12/ pitch) Chimney Sections P325k Used to build “SK”...
Page 21 CR Series Woodburning Fireplaces Accessory Description Model No. SKDSBL Used to terminate chimney at the top of a chase. Flashing is not PKDSBL included. Appropriate adapter is required. See Sections 2 and 3. Chase Top P325p CT100 Used to terminate Type “SK8” 2 wall chimney at the top of a chase.
Page 22 CR Series Woodburning Fireplaces 20001316...
Page 23 PRE-ENGINEERED Fireplace Systems ® the Fireplace, and operated at all times under normal condi- CFM Corporation warrants its MAJESTIC FIREPLACES® Pre- tions, use and service according to the operative instructions Engineered Fireplace (“Fireplace”) and the CFM Corporation furnished with the Fireplace, and only if and so long as the supplied ﬁregrate, glass doors, outside air system, fan motor,...
Page 24 CFM Corporation 410 Admiral Blvd. • Mississauga, Ontario, Canada L5T 2N6 800-668-5323 • www.cfmcorp.com...

This manual is also suitable for:

Cr36l