Advertisement
Quick Links
Advertisement
Related Manuals for Prism RevEAL Studio3
Summary of Contents for Prism RevEAL Studio3
-
Page 1: User Manual
User Manual RevEAL Studio3 User Manual – April 2013 - Prism Projection, Inc. -
Page 2: Basic Installation
• It is not intended for use on dimming circuits. • Contact Prism Projection Service and Support prior to any service work or the product warranty may be voided. Basic Installation Before installing this product please make sure that you have read all warnings and safety information provided in this manual. -
Page 3: Product Overview
The air vents located around the top portion of the fixture body should be clear of obstructions. Product Overview Beam Angles Adjustment 10‐90 Degrees 9 5/8” Accessory Slot Barn Doors Yoke Slide Adjustment Screw (2) Set Knob Yoke Position Knob RevEAL Studio3 User Manual – April 2013 - Prism Projection, Inc. -
Page 4: User Interface
Navigation Buttons can be used to access control settings and display fixture status on the Navigation Screen. Intensity or CCT Adjustment Knob Air Filter – Remove screws (4) to clean Navigation Buttons Power O LCD Menu Screen Switch (Con R36 Ethernet Jack DMX 5‐Pin In and Out PowerCon connector power in and out. RevEAL Studio3 User Manual – April 2013 - Prism Projection, Inc. - Page 5 Light output is reduced by approximately 40%. Set Refresh Rate to Medium for most applications. High is intended for high frame rate uses. Fixture options will vary depending on model number. RevEAL Studio3 User Manual – April 2013 - Prism Projection, Inc.
- Page 6 X,Y coordinate values to assure TrueSource active color calibration is active and monitoring performance. Yoke Bolt – Detaches yoke from housing Yoke Slide – Loosen hex screws to adjust position RevEAL Studio3 User Manual – April 2013 - Prism Projection, Inc.
- Page 7 RevEAL Studio3 DMX Chart Variable White Menu Settings: Channel Personality> White (Full White, Variable White) Channel Personality> Intensity (Linear, Standard) Channel Personality> Advanced Settings > Energy (Full, Eco) Channel Personality> Advanced Settings > Refresh Rate Advanced Settings > Algorithm Advanced Settings >...
- Page 8 RevEAL Studio3 DMX Chart Fixed White Menu Settings: Channel Personality> White (Full White) Channel Personality> Intensity (Linear, Standard) Channel Personality> Advanced Settings > Energy (Full, Eco) Channel Personality> Advanced Settings > Refresh Rate Advanced Settings > Algorithm Control 8 Bit...
- Page 9 RevEAL Studio3 DMX Chart Variable White + Correction Menu Settings: Channel Personality> White (Variable CCT, CCT + Correction) Channel Personality> Intensity (Linear, Standard) Channel Personality> Advanced Settings > Energy (Full, Eco) Channel Personality> Advanced Settings > Refresh Rate Advanced Settings > Algorithm...
- Page 10 RevEAL Studio3 DMX Chart Color + Variable White + Correction Menu Settings: Channel Personality> Color (X,Y) Channel Personality> White (Variable CCT, CCT + Correction) Channel Personality> Intensity (Linear, Standard) Channel Personality> Advanced Settings > Energy (Full, Eco) Channel Personality> Advanced Settings > Refresh Rate Advanced Settings >...
- Page 11 Modes and DMX Channels Operating modes are set by using the button pad to navigate to the Personality and Fixture Address Menus. The menu allows the user to adjust; Color Mode, Color Temperature, Intensity (dimmer curve) and select Advanced Features such as power control. Remote power setting permits the user to control ECO and FULL power setting via DMX.
- Page 12 If CCT is at any value other than 0 and the Color Mode is any setting other than None, the instrument will ignore the color channels and only create white light. Moving the CCT channel to 0 will bump the instrument to wherever the color channels are set.
- Page 13 Standalone Control Navigating to Standalone Control allows the user to create light without DMX present. To ensure there is no change in the light being produced it is recommended that DMX cables be removed while using standalone control. Use the up and down arrows to select the parameter to change, then use the left right arrows to change the parameter.
- Page 14 Prism Projection, Inc. 8228 East 124 Street South Sully, IA 50251 +1 (641) 594‐3356 info@prismprojection.com To receive an electronic copy of this user manual, please scan the QR code below. ...