SecurityMan ® Economical 4-Ch Standalone Digital Video Recorder MENU EDIT PAUSE PLAY STOP DOWN User's Manual DVR-04...
Page 2
Limitation of Liability The liability of SecurityMan Inc,. arising from this warranty and sale shall be limited to a refund of the purchase price. In no event shall SecurityMan be liable for costs of procurement of substitute products or services, or for any lost profits, or for any consequential, incidental, direct or indirect damages, however caused and on any theory of liability, arising from this warranty and sale.
One ATA-100 Hard Disk Interface, Support Over 200G Byte • Time Schedule Record / Sensor Triggered Record / Motion Triggered Record 1.2 Package Includes: • DVR-04, 4 Channel Digital Video Recorder • Power Cable and 12V DC adapter • USB Cable •...
DVR Installation 3.1 Install Hard Disk (For DVR model without HDD installed) Connect power cord and data cable to hard disk, use screws to mount hard disk and tighten well to the iron of the DVR housing. CAUTION: Do not open the cover while DVR is on!!!! 3.2 Connect Camera and Monitor There are 4 camera input and 2 monitor output with BNC connector.
DVR Installation 4.1 Detect Installed Hard Disk Connect the power cord and turn the DVR switch on. The system will boot-up and detect installed hard disk. The monitor display will show Master and Slave HDD Checking....hard-disk information. MASTER HARD DRIVE Please refer to the hard disk section of the manual to IBM-DHEA-36481 configure hard disk sequence.
DVR Installation 4.4 Main Screen When the DVR is turned on for the first time all cam- era will be OFF by default. Please refer to section 5.2 to switch on all cameras. • Upper left -> Percentage of Hard Disk Space Used •...
DVR Setup 5.1 Setup Menu Press “ Menu” to enter setup menu MAIN MENU Use “ Up” and “ Down” to browse > CAMERA SELECT 1234 RECORD SELECT 1234 Press “ Select” to modify setting RECORD MODE EACH Press “ Menu”...
DVR Setup 5.4 Record Mode There are two modes for video recording. Each Mode Compress and record each channel video separately, therefore, user can enlarge single channel video to full screen display. For example, user can turn off record function of CH1 and CH2 to have the system only record CH3 and CH4 video.
DVR Setup 5.8 Sub Menu—Password Change System default password : Press six times the “ CH1” button All keys can be used to set the password except the “ Menu” key, which is used for confirming and exit. If you forget the password, please do not worry. Just CURRENT PASSWORD :..
Notice: Please use this function to format the HDD at the time of installation, otherwise a PC will not recognize the DVR’s HDD when connecting to it through the USB cable. SLAVE HDD SIZE (For DVR-04 Pro Series) It shows the space of the secondary hard disk drive installed in the DVR.
DVR Setup 5.14 Sensor Setup SENSOR RECORD TIME SENSOR SETUP This number indicates the recording duration after the sensor is triggered. > SENSOR RECORD TIME ALARM OUT TIME ALARM OUT TIME It controls how long (in seconds) the alarm sound CHANNEL~1 TYPE:NORMAL-OPEN lasts after it is set off.
DVR Setup 5.15 Motion setup The first step is to setup video record method by Motion Triggered. Please refer back to 5.7 Record Schedule. MOT LEVER: User can press “ Select” to adjust sensitivity grade MOTION SET of motion detection. MOT LEVEL MOT REC TIME High(1----------10)Low...
Record 6.1 Start Recording Press “ Record” to start recording. System will display some information on screen. Only EACH MODE can enlarge single channel to full screen display • 1 Hard Disk Percentage Used • 2 “ ” Recording Symbol •...
Record 6.3 Recording Length Estimated record time based on 80GB/200GB/250GB HDD Unit: Hour 80GH Format Quality Frame Rate 1165 NTSC NORMAL 1153 1942 200GH Format Quality Frame Rate 2913 NTSC NORMAL 3884 4855 250GH Format Quality Frame Rate 3641 NTSC NORMAL 4855 6068...
Playback Press “ Play” and the system will list all the recorded video files from the HDD. The newest video file will appear as 01 on the list, press “ Move Up” and “ Move Down” to select the start time and press “...
USB Programming 8.1 Install 1. Put the USB Driver Program CD in your CD-ROM 2. Go to the CD-ROM and execute “setup.exe” 3. Use default destination folder 4. Execute: start>Program>DVR Play Note: This software currently supports Windows 2000 and Windows XP! 8.2 Program Interface Run the program (double click “...
Page 18
USB Programming Button Function 1 Save Frame 13 Backward play 2 Save Video Clip 14 Pause 3 Config 15 Play 4 Print (print the screen) 16 Step forward (frame by frame) 5 Event List 17 Fast forward 6 Channel 2 18 Status Bar 7 Channel 1 19 Play DVR video file...
Page 19
USB Programming Press to open the event video list. Press to change the recorded video location, directory, and other software settings.
Page 20
USB Programming Press to play the video...