Related Manuals for Intel SRCSATAWB
Summary of Contents for Intel SRCSATAWB
- Page 1 ® Intel RAID Controller SRCSATAWB Hardware User’s Guide Intel Order Number: D92006-001...
- Page 2 Intel may make changes to specifications and product descriptions at any time, without notice. Intel is a trademark or registered trademark of Intel Corporation or its subsidiaries in the United States and other countries. *Other names and brands may be claimed as the property of others.
-
Page 3: Preface
SRCSATAWB. • Chapter 2 describes the procedures for installing the RAID controller. • Chapter 3 provides the characteristics and technical specifications for the Intel RAID Controller SRCSATAWB. • Appendix A explains drive roaming and how to do a drive migration. - Page 4 Intel® RAID Controller SRCSATAWB Hardware User’s Guide...
-
Page 5: Table Of Contents
SATA Features of the 1078 Controller ... 4 Beep Codes ... 5 ® Chapter 2, Intel RAID Controller SRCSATAWB Hardware Installation ... 6 Requirements ... 6 Install the RAID Controller ... 6 Configure the RAID Controller ... 9 Replacing a Controller, Resolving a Config Mismatch ... 9 ®... -
Page 6: Chapter 1, Overview
SATA media. As a third generation PCI Express storage controller, the Intel SRCSATAWB addresses the demand for increased data throughput and scalability requirements across entry-level and midrange server platforms. The controller can be connected to up to eight drives directly and allows the use of expanders to connect to additional drives. -
Page 7: Operating System Support
The operating systems supported may not be supported by your server board. See the tested operating system list for your server board at http://support.intel.com/support/motherboards/server/. See also the tested hardware and operating system list for the RAID Controller SRCSATAWB to make sure the RAID card supports your operating system. Usability •... -
Page 8: Redundancy And Error Handling
Firmware provides best effort to recognize an error and recover if possible. • Failures are logged from controller and drive firmware, and SMART monitor. • Failures are logged in NVRAM, viewable from OS Event Log, Intel Console 2; CIM, LEDs, and via alarm. • Multiple cache options allow configuration-specific performance optimization: —... -
Page 9: Sata Features Of The 1078 Controller
Allows addressing of multiple SATA targets through an expander if using SATA 2.0- compliant hard disk drives. • Allows multiple initiators to address a single target (in a fail-over configuration) through an expander. Intel® RAID Controller SRCSATAWB Hardware User’s Guide... -
Page 10: Online Capacity Expansion And Raid Level Migration Rules
To disable the alarm, choose Disable Alarm. To enable alarm, choose Enable Alarm. To disable alarm only until the next event or until next power cycle, choose Silence Alarm. Intel® RAID Controller SRCSATAWB Hardware User’s Guide... -
Page 11: Chapter 2, Intel Raid Controller Srcsatawb Hardware Installation
The Resource CD, which contains drivers and documentation. • SATA hard drives. Note: Intel Corporation strongly recommends using an uninterruptible power supply (UPS). Install the RAID Controller 1. Turn off the power to the system and all drives, enclosures, and system components. - Page 12 Do not attempt to install a SAS drive. Only connect to a SATA drive or to a SAS/SATA backplane. The RAID Controller SRCSATAWB uses an advanced software stack that allows connections to SATA drives either directly or via SAS or SATA backplanes with or without expanders.
- Page 13 AF002211 Figure 3. Connecting Cables between the RAID Controller and Drives/Backplane 6. Install the server system cover and connect the power cords. See your server system documentation for instructions. Intel® RAID Controller SRCSATAWB Hardware User’s Guide...
-
Page 14: Configure The Raid Controller
After you press the keys to enter the Intel firmware takes several seconds to initialize and then display the RAID Controller SRCSATAWB number and firmware version. The numbering of the RAID controller follows the PCI slot scanning order used by the server board. -
Page 15: Chapter 3, Intel ® Raid Controller Srcsatawb Characteristics
C header (SES2) Battery connector Internal SAS/SATA port connector Internal SAS/SATA port connector Firmware recovery jumper Intel® RAID Controller SRCSATAWB Hardware User’s Guide Embedded RAM J1 J2 LSI* 1078 ROC Type 2-pin Provides signal to indicate cache needs to write header data. -
Page 16: Technical Specifications
Small, thin cables do not restrict airflow; Shared connectors for multiple drives 32 Kb NVRAM and config-on-disk (COD) In-band and out-of-band SES2 Assumes one SEP per enclosure 128 arrays per controller; 16 drives per array; 16 virtual drives per array. Intel® RAID Controller SRCSATAWB Hardware User’s Guide... -
Page 17: Array Performance Features
Optional Battery Backup Drive Replacement Drive Rebuild Using Hot Spares Error Checking and Indication Intel® RAID Controller SRCSATAWB Hardware User’s Guide 2.5 Gigabit/s per PCI Express* lane 3 Gigabit/s per lane 26 elements 6.4 Mbytes in 64 Kbyte stripes... -
Page 18: Electrical Characteristics
® The Intel RAID Controller SRCSATAWB meets or exceeds the requirements of UL flammability rating 94 V0. Each bare board is marked with the supplier name or trademark, type, and UL flammability rating. For the boards installed in a PCI bus slot, all voltages are lower than the SELV 42.4 V limit. - Page 19 Intel® RAID Controller SRCSATAWB Hardware User’s Guide...
-
Page 20: Appendix A: Drive Roaming And Drive Migration Install
6. Follow the instructions that came with your server system to remove the server cover. 7. Plug in and power on the system. The controller detects the RAID configuration from the configuration data on the drives (COD). Migration Install Intel® RAID Controller SRCSATAWB Hardware User’s Guide... -
Page 21: Drive Migration
9. Follow the instructions that came with your server system to remove the server cover. 10. Plug in and power on the system. When you start the system, the controller detects the RAID configuration from the configuration data on the drives. Intel® RAID Controller SRCSATAWB Hardware User’s Guide... -
Page 22: Appendix B: Installation / Assembly Safety Instructions
When working inside your computer: • Do not attempt to service the computer system yourself, except as explained in this guide and elsewhere in Intel documentation. Always follow installation and service instructions closely. • Turn off your computer and any peripherals. - Page 23 • When transporting a sensitive component, first place it in an antistatic container or packaging. • Handle all sensitive components in a static-safe area. If possible, use antistatic floor pads and workbench pads. Intel® RAID Controller SRCSATAWB Hardware User’s Guide...
-
Page 24: English
English Read all caution and safety statements in this document before performing any of the instructions. See also Intel Server Boards and Server Chassis Safety Information on the Resource CD and/or at http:\\support.intel.com\support\motherboards\server\sb\cs- 010770.htm. The power button on the system does not turn off system AC power. -
Page 25: Deutsch
Deutsch Lesen Sie zunŠchst sŠmtliche Warn- und Sicherheitshinweise in diesem Dokument, bevor Sie eine der Anweisungen ausfŸhren. Beachten Sie hierzu auch die Sicherheitshinweise zu Intel-Serverplatinen und -ServergehŠusen auf der Ressourcen-CD oder unter http:\\support.intel.com\support\motherboards\server\sb\cs-010770.htm. Intel® RAID Controller SRCSATAWB Hardware User’s Guide A microprocessor and heat sink may be hot if the system has been running. - Page 26 Der Mikroprozessor und der Kühler sind möglicherweise erhitzt, wenn das System in Betrieb ist. Außerdem können einige Platinen und Gehäuseteile scharfe Spitzen und Kanten aufweisen. Arbeiten an Platinen und Gehäuse sollten vorsichtig ausgeführt werden. Sie sollten Schutzhandschuhe tragen. Intel® RAID Controller SRCSATAWB Hardware User’s Guide...
-
Page 27: Français
Français Lisez attention toutes les consignes de sŽcurité et les mises en garde indiquŽes dans ce Intel® RAID Controller SRCSATAWB Hardware User’s Guide Notez que le commutateur CC de mise sous tension /hors tension du panneau avant n'éteint pas l'alimentation CA du système. Pour mettre le système hors tension, vous devez débrancher chaque... -
Page 28: Español
Consultez Intel Server Boards and Server Chassis Safety Information sur le CD Resource CD ou bien rendez-vous sur le site http:\\support.intel.com\support\motherboards\server\sb\cs-010770.htm. Español Lea todas las declaraciones de seguridad y precaucion de este documento antes de realizar cualquiera de las instrucciones. -
Page 29: Italiano
Italiano Intel® RAID Controller SRCSATAWB Hardware User’s Guide Después de completar las seis instrucciones de SEGURIDAD mencionadas, ya puede extraer las tapas del sistema. Para ello: 1. Desbloquee y extraiga el bloqueo de seguridad de la parte posterior del sistema, si se ha instalado uno. - Page 30 Se il sistema è stato a lungo in funzione, il microprocessore e il dissipatore di calore potrebbero essere surriscaldati. Fare attenzione alla presenza di piedini appuntiti e parti taglienti sulle schede e sul telaio. È consigliabile l'uso di guanti di protezione. Intel® RAID Controller SRCSATAWB Hardware User’s Guide...
-
Page 31: Product Regulatory Compliance Markings
• ETL NRTL Mark (US/Canada) • FCC Mark (US) • ICES-003 (Canada) • CE Mark (Europe) • VCCI Mark (Japan) • MIC Mark (Korea) Intel® RAID Controller SRCSATAWB Hardware User’s Guide Regulatory and Certification Information... - Page 32 (2) This device must accept any interference received, including interference that may cause undesired operation. Canada CANADA ICES-003 CLASS A CANADA NMB-003 CLASSE A Canada CANADA ICES-003 CLASS B CANADA NMB-003 CLASSE B Japan Japan Intel® RAID Controller SRCSATAWB Hardware User’s Guide...
-
Page 33: Electromagnetic Compatibility Notices
• Reorient or relocate the receiving antenna. • Increase the separation between the equipment and the receiver. Intel® RAID Controller SRCSATAWB Hardware User’s Guide Country Marking Taiwan Korea Australia... - Page 34 • Consult the dealer or an experienced radio/TV technician for help. Intel is not responsible for any radio or television interference caused by unauthorized modification of this equipment for substitution or attachment of connecting cables and equipment other than those specified by Intel. The correction of interferences caused by such unauthorized modification, substitution, or attachment will be the responsibility of the user.
Need help?
Do you have a question about the SRCSATAWB and is the answer not in the manual?
Questions and answers