SOYO SY-6IWM/L User Manual
  1. Manuals
  2. Brands
  3. SOYO Manuals
  4. Motherboard
  5. SY-6IWM/L
  6. User manual

SOYO SY-6IWM/L User Manual

Pentium iii, pentium ii & celeron processor supported fw82810 agp/pci/amr 66/100 mhz front side bus supported micro atx form factor
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
SY-6IWM/L
Motherboard
****************************************************
®
®
Pentium
III, Pentium
II & Celeron™
Processor supported
FW82810 AGP/PCI/AMR
66/100 MHz Front Side Bus supported
Micro ATX Form Factor
****************************************************
User's Manual

Advertisement

Table of Contents
loading

Related Manuals for SOYO SY-6IWM/L

Summary of Contents for SOYO SY-6IWM/L

  • Page 1 SY-6IWM/L Motherboard **************************************************** ® ® Pentium III, Pentium II & Celeron™ Processor supported FW82810 AGP/PCI/AMR 66/100 MHz Front Side Bus supported Micro ATX Form Factor **************************************************** User's Manual...
  • Page 2 It is the policy of Soyo Computer Inc. to respect the valid patent rights of third parties and not to infringe upon or to cause others to infringe upon such rights.

  • Page 3: Table Of Contents

    Table of Contents CHAPTER 1 MOTHERBOARD DESCRIPTION ........1 INTRODUCTION ............1 KEY FEATURES .............1 HANDLING THE MOTHERBOARD ......3 ELECTROSTATIC DISCHARGE PRECAUTIONS ..3 SY-6IWM/L MOTHERBOARD LAYOUT.......4 SY-6IWM/L MOTHERBOARD COMPONENTS ....5 CHIPSET .................7 I/O INTERFACE CONTROLLER ........13 AUDIO SUBSYSTEM ...........15 1-10 HARDWARE MONITOR..........16 1-11 WAKE ON LAN TECHNOLOGY........16...
  • Page 4 Table of Contents SY-6IWM/L INTEGRATED PERIPHERALS ........65 POWER MANAGEMENT SETUP ........69 PNP/PCI CONFIGURATION SETUP......72 PC HEALTH STATUS............75 LOAD OPTIMIZED DEFAULTS........77 3-10 LOAD FAIL-SAFE DEFAULTS........78 3-11 SUPERVISOR PASSWORD...........79 3-12 USER PASSWORD............80 3-13 IDE HDD AUTO DETECTION ........81 CHAPTER 4 DRIVERS INSTALLATION ..........82...

  • Page 5: Chapter 1 Motherboard Description

    Supports 66/100 MHz Front Side Bus Frequency Ø Auto-detect CPU voltage Ø Chipset integrated 3D AGP Accelerator Ø Easy CPU settings in BIOS with the “SOYO COMBO Setup” Ø PC98, ACPI Ø Ultra DMA33/66 (ATA 33/66) Ø Supports Wake-On-LAN (WOL) Ø...
  • Page 6 Motherboard Description SY-6IWM/L Ø Fan speed control Ø Battery Low voltage Detect Ø Supports multiple-boot function Ø Y2K Complaint Ø Supports Audio Modem Riser slot (AMR 1.0 compliant) * Ø 3 x 32-bit bus mastering PCI slots Ø 2 x USB ports onboard (USB3 share USB1) Ø...

  • Page 7: Handling The Motherboard

    Motherboard Description SY-6IWM/L 1-3 HANDLING THE MOTHERBOARD To avoid damage to your Motherboard, follow these simple rules while unpacking: Ø Before handling the Motherboard, ground yourself by grasping an unpainted portion of the system's metal chassis. Ø Remove the Motherboard from its anti-static packaging. Hold the Motherboard by the edges and avoid touching its components.

  • Page 8: Sy-6Iwm/L Motherboard Layout

    Motherboard Description SY-6IWM/L 1-5 SY-6IWM/L MOTHERBOARD LAYOUT ATX Power PS/2 KB PS/2 Mouse Connector Connector CPUFAN Slot 1 USB 1 USB 2 Intel Lithium COM 1 FW82810 Battery USB3 COM2 IDE 2 IDE 1 SDRAM SDRAM JOYSTICK JP44 LINE-OUT Header...

  • Page 9: Sy-6Iwm/L Motherboard Components

    Motherboard Description SY-6IWM/L 1-6 SY-6IWM/L MOTHERBOARD COMPONENTS...
  • Page 10 Motherboard Description SY-6IWM/L COM 2 Connector Power On by Keyboard Jumper Wake-On-LAN( WOL) Header Slot 1 Connector CPU Cooling Fan Connector Intel FW82810 Chip ATX Power Supply Connector DIMM Bank Floppy Disk Drive (FDD) Port 3V Lithium Battery USB3 Connector...

  • Page 11: Chipset

    Motherboard Description SY-6IWM/L 1-7 CHIPSET To compliment the Intel ® Celeron processor, the Intel ® 810 chipsets delivers a balanced platform solution for value computing. The 810 chipset is a highly-integrated three-chip solution consisting of a Graphics & Memory Controller (Intel 82810), an I/O Controller (Intel82801), and a Firmware Hub (Intel 82802).
  • Page 12 Motherboard Description SY-6IWM/L technology. The 82810 chip optimizes system memory arbitration, similar to AGP technology, resulting in a more responsive and cost-effective system. The 82810 Graphics Memory Controller Hub (GMCH) features Intel ® graphics technology and software drivers, using Direct AGP (integrated AGP) to create vivid 2D and 3D effects and images.
  • Page 13 Motherboard Description SY-6IWM/L The Integrated Audio-Codec 97 controller enables software audio and modem by using the processor to run sound and modem software. By reusing existing system resources, this feature adds flexibility, and improves sound quality. The 82802 Firmware Hub (FWH) stores system BIOS and video BIOS, eliminating a redundant nonvolatile memory component.
  • Page 14 Motherboard Description SY-6IWM/L Ø Intel ® 3D graphics with Direct AGP Vivid 2D and 3D graphics, efficient use of system memory for graphics, O/S and applications Ø Optional 4MB of dedicated display cache video memory Enables SKU differentiation with increased 3D graphics performance improvement over Direct AGP Ø...
  • Page 15 Motherboard Description SY-6IWM/L computer is running Automatic mapping of function to driver and configuration Support for isochronous and asynchronous transfer types over the same set of wires Support for up to 127 physical devices Guaranteed bandwidth and low latencies appropriate for telephony,...
  • Page 16 Motherboard Description SY-6IWM/L 1-7.2 IDE Support The motherboard has two independent bus-mastering PCI IDE interfaces. These interfaces support PIO Mode3, PIO Mode 4, ATAPI devices (e.g., CD-ROM), and Ultra DMA/66 synchronous-DMA mode transfers. The BIOS supports logical block addressing (LBA) and extended cylinder head sector (ECHS) translation modes.

  • Page 17: I/O Interface Controller

    Motherboard Description SY-6IWM/L 1-7.3 Real-Time Clock, CMOS SRAM, and Battery The real-time clock is compatible with DS1287 and MC146818 components. The clock provides a time-of-day clock and a multicentury calendar with alarm features and century rollover. The real-time clock supports 256 bytes of battery-backed CMOS SRAM in two banks that are reserved for BIOS use.
  • Page 18 Motherboard Description SY-6IWM/L Compatible (standard mode) Bi-directional (PS/2 compatible) Bi-directional EPP. A driver from the peripheral manufacturer is required for operation. Bi-directional high-speed ECP 1-8.3 Diskette Drive Controller The I/O controller is software compatible with the 82077 diskette drive controller and supports both PC-AT and PS/2 modes. In the Setup program, the diskette drive interface can be configured for the following diskette drive capacities and sizes.

  • Page 19: Audio Subsystem

    Motherboard Description SY-6IWM/L <Ctrl><Alt><Del>, software reset. This key sequence resets the computer’s software by jumping to the beginning of the BIOS code and running the Power On Self Test (POST). 1-8.5 Infrared Support The IR connection can be used to transfer files to or from portable devices like laptops, PDAs, and printers.

  • Page 20: Hardware Monitor

    Motherboard Description SY-6IWM/L 1-10 HARDWARE MONITOR The optional hardware monitor subsystem provides low-cost instrumentation capabilities. The features of the hardware monitor subsystem include: Ø An integrated ambient temperature sensor Ø Fan speed sensors, which monitor the fan 1 and fan 2 connectors Ø...

  • Page 21: Chapter 2 Hardware Installation

    SY-6IWM/L Chapter 2 HARDWARE INSTALLATION Congratulations on your purchase of SY-6IWM/L Motherboard. You are about to install and connect your new Motherboard. Note: Do not unpack the Motherboard from its protective anti- static packaging until you have made the following preparations.

  • Page 22: Unpacking The Motherboard

    The SY-6IWM/L FW82810 AGP/PCI/AMR Motherboard u This Quick Start Guide u The Installation CD-ROM u SOYO 3-in-1 Bonus Pack CD-ROM (Norton AntiVirus, Ghost and Virtual Drive) u The Foldable URM (Universal Retention Mechanism) Set (Factory installed on this motherboard)

  • Page 23: Installation Guide

    Hardware Installation SY-6IWM/L 2-3 INSTALLATION GUIDE We will now begin the installation of the Motherboard. Please follow the step-by-step procedure designed to lead you to a complete and correct installation. Warning: Turn off the power to the Motherboard, system chassis, and peripheral devices before performing any work on the Motherboard or system.

  • Page 24: 2-3.1 Cpu Installation

    Hardware Installation SY-6IWM/L 2-3.1 CPU Installation Your SY-6IWM/L motherboard comes with a CPU retention set kit. The retention set is used to hold the processor attached to the Slot 1 CPU connector on the motherboard. Mark your CPU Frequency: Record the working frequency of your CPU that should be clearly marked on the CPU cover.
  • Page 25 Hardware Installation SY-6IWM/L Open the two sides by folding them up. Push the locks on top of the CPU inward.
  • Page 26 Hardware Installation SY-6IWM/L Insert the CPU into the retention module. The CPU fits in the CPU slot in only ONE way, do not try to force it in. After completely inserting the CPU, push the two locks on top of the CPU outward.
  • Page 27 Hardware Installation SY-6IWM/L Note: Installing a heat sink and cooling fan on top of your CPU is necessary for proper heat dissipation. Failing to install these items may result in overheating and possible burn-out of your CPU. 2-3.1.1 CPU Fan Installation Your Slot 1 processor kit comes with a cooling fan.

  • Page 28: 2-3.2 Sdram Memory Module Installation

    Hardware Installation SY-6IWM/L 2-3.2 SDRAM Memory Module Installation Your board comes with three DIMM sockets, and supports up to 512MB main memory using industry standard Synchronous DRAM (SDRAM), single or double-sided, 3.3V unbuffered DIMM modules from 8MB to 256MB. Registered DIMMs or DIMMs populated with 4 bit wide SDRAM devices are not supported.
  • Page 29 Hardware Installation SY-6IWM/L Number of Memory DIMM 1 DIMM 2 DIMM 3 Modules Double-sided/ Double-sided/ Single-sided Single-sided Double-sided/ Single-sided Single-sided² Single-sided RAM Type SDRAM¹ Memory Module Size (MB) 8/16/32/64/256 Mbytes Note: 1. PC100 Compliant DIMM module is required regardless of 66 or 100 MHz FSB speed.

  • Page 30: 2-3.3 Motherboard Connector

    Hardware Installation SY-6IWM/L 2-3.3 Motherboard Connector 2-3.3.1 IDE Device Installation (HDD, CD-ROM) Pin -1 IDE 2 IDE 1 Secondary Primary This Motherboard offers two primary and secondary IDE device connectors (IDE1, IDE2.) It can support up to four high-speed HDD or CD-ROM.
  • Page 31 Hardware Installation SY-6IWM/L 2-3.3.2 Floppy Drive Installation Pin -1 Floppy Drive Connector The system supports 5 possible floppy drive types: 720 KB, 1.2 MB, 1.44 MB, 2.88 MB, and LS-120. In addition, this Motherboard supports a 3-mode (720KB/1.2MB/1.44MB) floppy commonly used in Japan.
  • Page 32 Hardware Installation SY-6IWM/L 2-3.3.3 Front Panel Connections HDD LED Speaker ACPI LED Key Lock PWRBT Power LED Reset Plug the computer case's front panel devices to the corresponding headers on the Motherboard. 1. Power LED & KeyLock Plug the Power LED cable into the 5-pin Keylock header.
  • Page 33 Hardware Installation SY-6IWM/L 2. Reset Plug the Reset push-button cable into the 2-pin Reset header on the Motherboard. Pushing the Reset button on the front panel will cause the system to restart the boot-up sequence. Reset Pin Assignment Power Good 3.
  • Page 34 Hardware Installation SY-6IWM/L 5. IDE LED Attach the 2-pin IDE device LED cable to the corresponding IDE LED header on the Motherboard. This will cause the LED to lighten when an IDE (HDD, CD-ROM) device is active. HDD LED Pin Assignment LED Anode LED Cathode 6.
  • Page 35 Hardware Installation SY-6IWM/L 2-3.3.4 Back Panel Connections All external devices such as the PS/2 keyboard, PS/2 mouse, printer, modem, USB can be plugged directly onto the Motherboard back panel. Only after you have fixed and locked the Motherboard to the computer case can you start connecting the external peripheral devices.

  • Page 36: Hardware Installation

    Hardware Installation SY-6IWM/L PS/2 Mouse Printer Connector Joystick Connector USB2 PS/2 Keyboard USB1 Connector VGA Connector LINE-OUT LINE-IN Connector 1. Parallel Port PRT This parallel port is used to connect the printer or other parallel devices. Plug the parallel device cable into the 25-pin female connector located at the rear panel of the Motherboard.
  • Page 37 Hardware Installation SY-6IWM/L 3. Universal Serial Bus USB1/USB2 This Motherboard provides two USB ports for your additional devices. Plug the USB device jack into the available USB connector USB1 or USB2. Standard device drivers come with the Win98 for commonly used USB devices.
  • Page 38 Hardware Installation SY-6IWM/L 2-3.3.5 Other Connections 1. Serial Port COM2 In addition to the onboard serial connector COM1 located at the rear panel, your Motherboard comes with a second serial port COM2 equipped with a flat cable and external connector.
  • Page 39 Hardware Installation SY-6IWM/L 2. Wake-On-LAN (WOL) Attach the 3-pin connector from the LAN card which supports the Wake- On-LAN (WOL) function to the JP44 header on the Motherboard. This WOL function lets users wake up the connected computer through the LAN card.
  • Page 40 Hardware Installation SY-6IWM/L 3. Infrared (IR1) Plug the 5-pin infrared device cable to the IR1 header. This will enable the infrared transfer function. This Motherboard meets both the ASKIR and HPSIR specifications. Please install according to the following pin assignment:...
  • Page 41 Hardware Installation SY-6IWM/L 5. Aux-in (J10) For Auxiliary Audio devices (1.0Vrms typ.). AUX-IN: J10 Left Right 6. Phone-in (J11) Connect to modem sound connector. PHONE-IN: J11 Mono...
  • Page 42 CPUFAN connector on the Motherboard. The fan will stop when the system enters into Suspend Mode. (Suspend mode can be enabled from the BIOS Setup Utility, [Soyo Combo] menu.) To avoid damage to the system, install according to the following pin...
  • Page 43 Hardware Installation SY-6IWM/L (2) Chassis Cooling Fan Some chassis also feature a cooling fan. This Motherboard features a CHAFAN connector to provide 12V power to the chassis fan. Connect the cable from the chassis fan to the CHAFAN 3-pin connector. Install...
  • Page 44 Hardware Installation SY-6IWM/L 2-3.3.6 AGP VGA Card This motherboard comes with integrated AGP subsystem therefore, AGP VGA card is not needed. Other Display Cards: Insert other types of VGA cards into the PCI or ISA expansion slots according to card specifications.
  • Page 45 Hardware Installation SY-6IWM/L Warning: Follow these precautions to preserve your Motherboard from any remnant currents when connecting to power supply: Turn off the power supply and unplug the power cord of the power supply before connecting to PW connector. This motherboard requires a power supply, that meets the SFX 1.1 or ATX 2.03 specifications.
  • Page 46 Hardware Installation SY-6IWM/L 2-3.3.8 AMR (Audio Modem Riser)Connector This motherboard supports AMR (Audio-Modem Riser) slot that facilitates audio or modem riser card expansion. Since AC97 audio codec is built-in down on the motherboard, only “Secondary” mode modem riser (MR) card can be used on the AMR slot.

  • Page 47: 2-3.4 Jumper Setting

    Hardware Installation SY-6IWM/L 2-3.4 Jumper Setting Step 1. Enable/Disable Power-On by Keyboard (JP1) You may choose to enable the Power-On through Keyboard function by shorting pin 1-2 on jumper JP1; or short pin 2-3 to disable this function. Power-On by...

  • Page 48: 2-3.5 Cmos Clearing (Jp5)

    Hardware Installation SY-6IWM/L 2-3.5 CMOS Clearing (JP5) After you have turned off your computer, clear the CMOS memory by momentarily shorting pins 2-3 on jumper JP5, for a few seconds. Then restore JP5 to the initial 1-2 jumper setting in order to recover and retain the default settings.

  • Page 49: 2-3.7 Quick Bios Setup

    This Motherboard does not use any hardware jumpers to set the CPU frequency. Instead, CPU settings are software configurable with the BIOS [Soyo Combo Feature]. The [Soyo Combo Feature] menu combines the main parameters that you need to configure, all in one menu, for a quick setup in BIOS.
  • Page 50 Step 2. Select [Load Optimized Defaults] Select the “Load Optimized Defaults” menu and type “Y” at the prompt to load the BIOS optimal setup. Step 3. Select [Soyo Combo Feature] (a) CPU Host/PCI Clock CPU Host / PCI Clock The PCI clock frequency depends on...

  • Page 51: 2-3.8 Troubleshooting At First Start

    Hardware Installation SY-6IWM/L 2-3.8 Troubleshooting at First Start What should I do if the Motherboard refuses to start? Check that all DIMM memory modules are inserted completely. Sometimes a DIMM that is not inserted properly can cause boot problems. Check whether all Add-on cards have been inserted properly. Re- insert the Add-on cards to make sure that they make proper contact with the slots.

  • Page 52: 2-3.9 Power Off

    Hardware Installation SY-6IWM/L 2-3.9 Power Off There are two possible ways to turn off the system: Use the Shutdown command in the Start Menu of Windows 95/98 to turn off your computer. Press the mechanical power-button and hold down for over 4 seconds, to shutdown the computer.

  • Page 53: Chapter 3 Bios Setup Utility

    BIOS Setup Utility SY-6IWM/L Chapter 3 BIOS SETUP UTILITY This Motherboard's BIOS setup program uses the ROM PCI/ISA BIOS program from Award Software Inc. To enter the Award BIOS program's Main Menu: 1. Turn on or reboot the system. 2. After the diagnostic checks, press the [Del] key to enter the Award BIOS Setup Utility.
  • Page 54 BIOS Setup Utility SY-6IWM/L Hot Keys: Function keys give you access to a group of commands throughout the BIOS utility. Function Command Description Gives the list of options available for each General Help item. Previous Restore the old values. These are the values Values that the user started the current session with.

  • Page 55: Save And Exit Setup

    BIOS Setup Utility SY-6IWM/L SAVE AND EXIT SETUP Select the [SAVE & EXIT SETUP] option from the Main Menu to save data to CMOS and exit the setup utility. This option saves all your changes and causes the system to reboot.

  • Page 56: Soyo Combo Setup

    <DEL> key during the system diagnostic checks to enter the Award BIOS Setup program. The CMOS SETUP UTILITY will display on screen. Then, select the [SOYO COMBO SETUP] option from the main menu and press the <Enter> key.
  • Page 57 BIOS Setup Utility SY-6IWM/L 3-1.1 Quick CPU Frequency Setup Quick CPU Setting Description Note Frequency Setup Select the host clock of your Slot 1 CPU Host/PCI Default 129/43 MHz processor among these values. Clock 66/33 MHz 133/44 MHz Note: For the 810 chipset, 66...
  • Page 58 BIOS Setup Utility SY-6IWM/L 3-1.4 Processor Number Feature Setting Setting Description Note Disabled Setting this item to enabled will allow Processor application programs to read the ID- Number Enabled Default code in your Pentium III CPU, disabling Feature this item will not allow any program to read the CPU ID code.
  • Page 59 BIOS Setup Utility SY-6IWM/L 3-1.7 Others Optional Setting Description Note POWER ON Password Enables you to wake-up the Function system by entering a password at the keyboard. Hot KEY You can wake-up the system by pressing the key combination of your choice (Ctrl-F1~F12).

  • Page 60: Standard Cmos Setup

    BIOS Setup Utility SY-6IWM/L 3-2 STANDARD CMOS SETUP Select the [STANDARD CMOS SETUP] option from the Main Menu and press [Enter] key. CMOS Setup Utility – Copyright ( C ) 1984-1999 Award Software Standard CMOS Features Date (mm:dd:yy) Fri, Jan 1 1999...
  • Page 61 BIOS Setup Utility SY-6IWM/L 3-2.2 Hard Disks Type & Mode Choose the type and mode for the hard disks that you have already installed. Primary Setting Description Note (Secondary) Master & Slave Press To auto-detect the HDD’s size, IDE HDD Auto- Enter head …...
  • Page 62 BIOS Setup Utility SY-6IWM/L 3-2.4 Others Optional Setting Description Note EGA/VGA Select the video mode. Default Video CGA 40 CGA 80 MONO (Monochrome) Halt On ALL Errors When the BIOS detects system Default errors, this function will stop the No Errors system.

  • Page 63: Advanced Bios Features

    BIOS Setup Utility SY-6IWM/L 3-3 ADVANCED BIOS FEATURES Select the [Advanced BIOS Features] option from the Main Menu and press [Enter] key. CMOS Setup Utility – Copyright ( C ) 1984-1999 Award Software Advanced BIOS Features Anti-Virus Protection Enabled Item Help...
  • Page 64 BIOS Setup Utility SY-6IWM/L 3-3.1 Virus Warning Setting Description Note Disabled If set to enabled, the Paragon Anti - Virus Anti-Virus. Function will scan Protection Enabled Default your boot drive for boot virusses. If a boot virus is detected, the BIOS will display a warning message.
  • Page 65 BIOS Setup Utility SY-6IWM/L 3-3.5 Boot Up NumLock Status Setting Description Note Boot Up Puts numeric keypad in Default NumLock NumLock mode at boot-up. Status Puts numeric keypad in arrow key mode at boot-up. 3-3.6 Gate A20 Options Setting Description...
  • Page 66 BIOS Setup Utility SY-6IWM/L 3-3.8 Security Option Use this feature to prevent unauthorized system boot-up or use of BIOS Setup. The following table describes the security settings. Setting Description System Each time the system is booted, the Security Option password prompt appears.

  • Page 67: Advanced Chipset Features

    BIOS Setup Utility SY-6IWM/L 3-4 ADVANCED CHIPSET FEATURES Caution: Change these settings only if you are already familiar with the Chipset. The [Advanced Chipset Features] option changes the values of the chipset registers. These registers control the system options in the computer.
  • Page 68 BIOS Setup Utility SY-6IWM/L CHIPSET FEATURES SETUP CHIPSET Setting Description Note FEATURES SDRAM CAS Use the default setting Latency Time Default SDRAM Cycle Use the default setting Time Tras/Trc Default Default SDRAM RAS- Use the default setting to-CAS Delay System BIOS...

  • Page 69: Integrated Peripherals

    BIOS Setup Utility SY-6IWM/L 3-5 INTEGRATED PERIPHERALS Caution: Change these settings only if you are already familiar with the Chipset. The [INTEGRATED PERIPHERALS] option changes the values of the chipset registers. These registers control the system options in the computer.
  • Page 70 BIOS Setup Utility SY-6IWM/L PERIPHERALS Menu and provide instructions on how to configure the IDE controls, FDC controls, and the onboard serial and parallel ports. 3-5.1 IDE Device Controls IDE Controls Setting Description Note Disabled Turn off the on-board On-Chip PCI IDE Ø...
  • Page 71 BIOS Setup Utility SY-6IWM/L 3-5.3 IDE HDD Block Mode Setting Description Note Disabled IDE HDD Block Mode Enabled Invokes multi-sector Default transfer instead of one sector per transfer. Not all HDDs support this function. 3-5.4 FDC Controls FDC Controls Setting...
  • Page 72 BIOS Setup Utility SY-6IWM/L 3-5.6 Onboard Parallel Ports Onboard Parallel Setting Description Note Ports Disabled Choose the printer I/O Onboard Parallel address. Port 378/IRQ7 Default 3BC/IRQ7 278/IRQ5 The mode depends on your Default Parallel Port Mode external device that connects to this port.

  • Page 73: Power Management Setup

    BIOS Setup Utility SY-6IWM/L Others Optional Setting Description Note Disabled Set the I/O address for the Default Midi Port Address on board Midi port here. If [Midi Port Address] is set to [330]/[300] mode Select the IRQ that the Midi Port IRQ...
  • Page 74 BIOS Setup Utility SY-6IWM/L 3-6.1 Power Management Controls Power Setting Description Note Management Controls Disabled ACPI function Enabled ACPI (Advanced Default Configuration Power Management Interface) S1 (POS) The system will enter the S1 ACPI Suspend state during suspend. (Low Type...
  • Page 75 BIOS Setup Utility SY-6IWM/L Power Management Controls (Continued) Power Setting Description Note Management Controls Disabled Default HDD Power Down Some older model 1-15Min When the set time has HDDs may not elapsed, BIOS sends a support this command to the HDD to advanced function.

  • Page 76: Pnp/Pci Configuration Setup

    BIOS Setup Utility SY-6IWM/L 3-7 PNP/PCI CONFIGURATION SETUP This option sets the Motherboard's PCI Slots. CMOS Setup Utility – Copyright ( C ) 1984-1999 Award Software PnP/PCI Configurations PNP OS Installed Item Help Reset Configuration Data Disabled Menu Level 4...
  • Page 77 BIOS Setup Utility SY-6IWM/L 3-7.1 PNP/PCI Configuration Controls PNP/PCI Setting Description Note Controls PnP OS Set this field to [Yes] if you Installed are running Windows 95, which is PnP compatible. If the OS you are running Default (If there is any...
  • Page 78 BIOS Setup Utility SY-6IWM/L PNP/PCI Configuration Setup (Continued) PNP/PCI Setting Description Note Setup Interrupt How to set the BIOS to release the IRQ to the PnP Interrupt pool: Line PnP / PCI configuration Integrated Peripherals IRQ 15 IRQ 15: PCI / ISA PnP On-Chip Secondary PCI IDE: disabled...

  • Page 79: Pc Health Status

    BIOS Setup Utility SY-6IWM/L 3-8 PC HEALTH STATUS This option sets the Motherboard's PC Health Status. CMOS Setup Utility – Copyright ( C ) 1984-1999 Award Software PC Health Status CPU Warning Temperature Disabled Item Help Current System Temp. 25 º C / 77 º F Current CPU Dio Temperature 40 º...
  • Page 80 BIOS Setup Utility SY-6IWM/L 3-8.1 CPU Device Monitoring CPU Device Setting Description Note Monitoring CPU Warning Disabled Default Temperature 50°C/122°F Set CPU temperature from 50°C 53°C/127°F to 70°C. The CPU will slow down when CPU temperature 56°C/132°F goes beyond the preset value.

  • Page 81: Load Optimized Defaults

    BIOS Setup Utility SY-6IWM/L 3-9 LOAD OPTIMIZED DEFAULTS Select the [Load Optimized Defaults] option from the Main Menu to load the system values you have previously saved. This option is recommended if you need to reset the system setup and to retrieve the old values.

  • Page 82: Load Fail-Safe Defaults

    BIOS Setup Utility SY-6IWM/L 3-10 LOAD FAIL-SAFE DEFAULTS Select the [Load Fail-Safe Defaults] option from the Main Menu to load the system values you have previously saved. This option is recommended if you need to reset the system setup and to retrieve the old values.

  • Page 83: Supervisor Password

    BIOS Setup Utility SY-6IWM/L 3-11 SUPERVISOR PASSWORD Based on the setting you have made in the [Security Option] of the [BIOS FEATURES SETUP] section, the password prevents access to the system or the setup program by unauthorized users. Follow this procedure to set a...

  • Page 84: User Password

    BIOS Setup Utility SY-6IWM/L Enter your new password and press [Enter]. The following message appears, prompting to confirm the new password: Confirm Password: Re-enter your password and then press [Enter] to exit to the Main Menu. This diagram outlines the password selection procedure: ↔...

  • Page 85: Ide Hdd Auto Detection

    BIOS Setup Utility SY-6IWM/L 3-13 IDE HDD AUTO DETECTION This Main Menu function automatically detects the hard disk type and configures the [Standard CMOS Features] accordingly. CMOS Setup Utility – Copyright ( C ) 1984-1999 Award Software IDE Primary Master...

  • Page 86: Chapter 4 Drivers Installation

    HTML format with information on SOYO Motherboards and other products. Step 1. Insert the SOYO CD into the CD-ROM drive The SOYO CD will auto-run, and the SOYO CD Start Up Menu will be shown as below. (SOYO CD Start Up Program Menu)
  • Page 87 6IWM/L Back (Manual Selection Menu) The user's manual files included on the SOYO CD can be read in PDF (Postscript Document) format. In order to read a PDF file, the appropriate Acrobat Reader software must be installed in your system.
  • Page 88 Drivers installation SY-6IWM/L However, to display the list of all drivers software available with SOYO Motherboards, click the Display all drivers on the SOYO CD button. Please make sure to install only the drivers adapted to your system, or otherwise this cause system malfunctions.
  • Page 89 Step 6. Enter the SOYO CD Click the Enter SOYO CD button to enter the SOYO HTML database. The Start Up program will activate the default HTML browser installed on your system (for example, Internet Explorer or Netscape) to visualize the contents of the SOYO CD.
  • Page 90 Internet Explorer* browser. Click YES to install the HTML browser. After the installation is complete, please restart your system. Then re-run the SOYO CD and you will be able to browse the SOYO HTML database. (* Internet Explorer is a Microsoft Trademark)

  • Page 91: Chapter 5 Sigmatel Audio Driver Installation

    Sigmatel Audio Drivers installation SY-6IWM/L Chapter 5 SIGMATEL AUDIO DRIVER INSTALLATION Installing the Sigmatel Audio Drivers under windows 98/ Windows Second Edition 1. Open Device Manager. 2. PCI Multimedia Device will have a yellow marker the first time the operating system is installed.
  • Page 92 Sigmatel Audio Drivers installation SY-6IWM/L Installing the Sigmatel Audio Drivers for Windows 1. Double click the MULTIMEDIA icon in the control panel. The Multimedia Properties windows will appear. Click on the Devices tab and press the Add button. 2. Select "Unlisted or Updated Drivers" from the list of drivers in the Add window by placing the mouse pointer over it and clicking the left mouse button.
  • Page 93 Sigmatel Audio Drivers installation SY-6IWM/L SynthCore Lite Application for Windows NT 4.0 The CD contains a SynthCore Lite application program, that the Quick Settings Guide does not describe. It can be installed by running win- wave.exe in the D:\drive-all\sigmatel\win-wave directory. (Were D is your CD-ROM drive letter).
  • Page 94 SY-6IWM/L...

Table of Contents