Using A Second Dvd Player Next To The Dvd1010 - Philips DVD Video Player Manual

BRAND CODE
Bang & Olufsen
592, 114
Grundig
097, 562, 581, 218, 232, 264, 561,
064, 222, 514, 614
Hitachi
172, 190, 252, 070, 178, 376, 383,
136, 071, 065, 244, 436, 063, 223,
225, 584, 083, 132, 333, 603, 043,
059, 254, 575, 605
JVC
080, 096, 063, 187, 217, 219, 398, 633
Panasonic
078, 277, 082, 241, 188, 264, 253,
190, 240, 394, 584
Philips
039, 583, 081, 350, 220, 064, 070,
114, 401, 581
Radiola
064, 350, 039
SBR
039, 064, 070, 220
Saba
232, 136, 528, 370, 114, 190, 240,
223, 314, 225, 362, 102, 326, 584
Samsung
087, 046, 205, 244, 291, 317, 397,
036, 057, 059, 064, 066, 083, 117,
454, 515, 583, 614
Schneider
064, 363, 350, 571, 330, 421, 084,
245, 274, 379, 398, 695
Sony
027, 037, 532, 063, 138, 107, 038, 678
Telefunken
333, 370, 136, 279, 528, 525, 289,
498, 652, 032, 083, 101, 111, 128,
240, 362
Thomson
528, 370, 136, 225, 232, 360, 223,
314, 326, 264, 426, 376, 587
Toshiba
062, 183, 580, 529, 270, 536, 535,
097, 087, 063, 181
20 PREPARATION
Using a second DVD player next to the
DVD1010
To operate the DVD1010 via the remote control without responce of a
second player to the remote control commands, you can switch the
remote and player to use a second set of remote control codes.
The default system code is Code 1.
Programming the DVD1010 to respond to different RC
code.
DNM STOP PLAY PAUSE
PEN/CLOSE
Selecting remote control code on remote control
ZOOM DNM
ANGLE
VOL CH
Programming the remote control
Your remote control can be used to control your television.
To control this equipment, the following buttons on the remote control
are available:
1
2
3
4
To program the DVD1010 to respond to Code1/Code 2, turn the
power OFF.
Simultaneously press the STOP 9 and PAUSE ; buttons on the
front panel of the player while turning the power ON.
After RCCODE1 or RCCODE2 appears on the display panel of the
player, release STOP 9 and PAUSE ; .
You can change the current code by pressing the PAUSE ; key
within 5 seconds.
To select Code 1 or Code 2 on the remote control, simultaneously
press the DNM button on the remote control and 1 or 2 on the
numerical keypad.
The remote control will now be set to the remote contol code
of your choice.
This action can be repeated whenever necessary.
VOL+, VOL-, CH+/- and c
To change the remote control for use with your brand of television,
select your brand from the next table. Note the first 3-digit code
number after the brand name.
Please press the DNM and RETURN button simultaneously for at
least 3 seconds.
Your remote cotrol is now disabled for all functions.
Enter the digits of the selected 3 digit code number within 30
seconds.
In case you press a wrong key or an incorrect number, repeat steps
1,2 and 3.
The remote control is now programmed to control your Television.
If it does not react properly on the mentioned buttons, select the
next 3 digit code number behind your brand of Television and
repeat step 2 and 3.