Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Hunter MB502-01
Summary of Contents for Hunter MB502-01
- Page 1 ENGLISH www.HunterFanInternational.com MB502-01 • 03/25/14 • © Hunter Fan Company...
- Page 3 We are proud of our work and appreciate the opportunity to Downrod Wiring Canopy Blades supply you with the best ceiling fan available anywhere in the world. Operation, Light Kit Remote Control Maintenance & Cleaning Troubleshooting MB502-01 • 03/25/14 • © Hunter Fan Company...
-
Page 4: What To Expect With Your Installation
Assess ceiling angle Select a downrod length installed and used in accordance with the instructions may cause fan weight harmful interference to radio communications. MB502-01 • 03/25/14 • © Hunter Fan Company... -
Page 5: Tools Needed
Go to www.HunterFan.com/FAQs and click “How do I properly install multiple remote- controlled fans?” for more information. Power Drill 9/64” Drill Bit (optional) (optional) If mounting to a support structure, you will also need these tools. MB502-01 • 03/25/14 • © Hunter Fan Company... -
Page 6: Mounting Options
You need BOTH You need ONLY a Longer a Longer Downrod & Downrod an Angled Mounting Kit *most common MB502-01 • 03/25/14 • © Hunter Fan Company... -
Page 7: Ceiling Bracket
To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet Refer to warning w.1 on pg. 2 box associated with the wall switch location. MB502-01 • 03/25/14 • © Hunter Fan Company... - Page 8 3 m (10’) or higher If you need a longer downrod, follow the steps in the “Instructions for Installing a Longer Downrod” manual included with your fan. MB502-01 • 03/25/14 • © Hunter Fan Company...
- Page 9 THE CANOPY OR WIRES. Place extending from the top of loosely on top of the fan. the downrod ball into the slot in the downrod. the ceiling bracket. 20 cm 1 cm (8”) (3/8”) MB502-01 • 03/25/14 • © Hunter Fan Company...
- Page 10 Spread the wires apart, with the grounded wires on one side of Refer to CAUTION c.1 on pg. 2 the outlet box and the ungrounded wires on the other side of the outlet box. MB502-01 • 03/25/14 • © Hunter Fan Company...
- Page 11 Insert the two canopy screws lifted into place, the canopy fits into the screw holes are aligned. found in the hardware bag. the hanging bracket as shown. Note: Fan style may vary. MB502-01 • 03/25/14 • © Hunter Fan Company...
- Page 12 Insert a blade into the motor housing. Attach each blade to the fan using two blade grommets, found in the hardware bag, and two blade assembly screws, found in the hardware bag. MB502-01 • 03/25/14 • © Hunter Fan Company...
-
Page 13: Light Kit
Make sure the light kit ring is securely attached. Failure to properly secure all three assembly screws could result in the light fixture falling. MB502-01 • 03/25/14 • © Hunter Fan Company... -
Page 14: Operation Instructions
Rotate the globe in a clockwise direction until it is held tightly in See next page for fan place by the three tabs. operation instructions. MB502-01 • 03/25/14 • © Hunter Fan Company... -
Page 15: Remote Control
Note: For rocker-style cover plates, fan, wait 1 minute then try again. If break off the tabs by pushing outward. Turn Power using the transmitter with multiple fans, repeat this process for each fan. MB502-01 • 03/25/14 • © Hunter Fan Company... - Page 16 To switch the direction of air flow, move the For cleaning the fan, use soft brushes or the lights will be completely off. reverse switch to the opposite position. cloths to prevent scratching. Cleaning products may damage the finishes. MB502-01 • 03/25/14 • © Hunter Fan Company...
-
Page 17: Troubleshooting
Transmitter only works when and click “How do I properly install held at close range multiple remote-controlled fans?” for information on how to correct this • Change battery. issue. MB502-01 • 03/25/14 • © Hunter Fan Company...
Need help?
Do you have a question about the MB502-01 and is the answer not in the manual?
Questions and answers