Advertisement
GENERAL & SPECIFIC
SAFETY INSTRUCTIONS
1. KNOW YOUR TOOL
Read and understand the owners manual and labels affixed to the tool. Learn its
application and limitations as well as its specific potential hazards.
2. DON'T USE power tools in damp or wet locations or expose them to rain. Keep work
area well lit and provide adequate surrounding work space.
3. USE RIGHT TOOL.
Don't force the tool or the attachment to do a job for which it was not designed.
4. WEAR PROPER APPAREL.
Do not wear loose clothing, gloves, neckties or jewelry (rings, watch) because they
could get caught in moving parts. Non-slip footwear is
protective hair covering to contain long hair. Roll up long sleeves above the elbows.
5. MAINTAIN TOOL WITH CARE.
Keep tool clean for best and safest performance. Follow instructions for operation
and changing accessories.
6. DISCONNECT TOOLS.
Before servicing, when changing accessories or attachments.
7. AVOID ACCIDENTAL STARTING.
Make sure the switch is in the ''OFF'' position before plugging in.
8. USE RECOMMENDED ACCESSORIES.
Consult the manual for recommended accessories. Follow the instructions that
accompany the accessories. The use of improper accessories may cause hazards.
9. CHECK FOR DAMAGED PARTS.
Before further use of the tool, a guard or other parts that are damaged should be
carefully checked to ensure they will operate properly and perform their intended
function. Check for alignment of moving parts, breakage of parts, mounting, and any
other conditions that may affect its operation. A guard or other parts which are
damaged should be properly repaired or replaced.
Specific Rules for Safe Operation
1. ALWAYS SWITCH OFF AND WAIT.
Wait for the blade to come to a complete stop before any type of adjustment or
maintenance.
2. AVOID CUTTING NAILS.
Make sure all nails are removed from the workpiece before operating.
3. MAKE SURE THE BALDE IS SEATED PROPERLY BEFORE OPERATING.
4. WAIT UNTIL THE BLADE REACHES ITS MAXIMUM SPEED BEFORE CUTTING.
5. KEEP HANDS AWAY FROM MOVING PARTS.
We recommend you save these instructions
WARNING!: If any parts are missing, do
not operate your jig saw until missing parts
are replaced. Failure to do so could result
in serious personal injury.
Technical Specifications
Stroke length ........................................................................................................5/8"
recommended. Wear
Max. cutting capacity at 90
Max. cutting capacity at 90
Strokes per minute ....................................................................................500-3,000
Voltage................................................................................................................120V
Amperage ..............................................................................................................6A
Cycle/Phase ........................................................................................60Hz, 1 phase
POWER SUPPLY
WARNING: YOUR JIG SAW MUST BE CONNECTED TO A 120V, 15-AMP CIRCUIT.
FAILURE TO CONNECT IN THIS WAY CAN RESULT IN INJURY FROM SHOCK OR
FIRE.
Your jig saw must be properly grounded. Not all outlets are properly grounded. If you
are not sure if your outlet is properly grounded, have it checked by a qualified
electrician.
WARNING: IF NOT PROPERLY GROUNDED, THIS JIG SAW CAN CAUSE
ELECTRICAL SHOCK, PARTICULARLY WHEN USED IN DAMP LOCATIONS.
EXTENSION CORDS
The use of any extension cord will cause some loss of power. Use the following chart
to determine the minimum wire gauge (A.W.G-American Wire Gauge) extension cord
needed. Only use polarized extension cords (one prong wider than the other) which
have 2-prong type plugs and 2-hole receptacles which accept the tool's plug.
For circuits that are further away from the electrical circuit box, the wire gauge must be
increased proportionate-
ly in order to deliver
ample voltage to the jig
saw. Refer to chart for
wire length and size.
SPECIFICATIONS &
ELECTRICAL INFORMATION
WARNING!: Do not use this product as a
component of others products. Also, do not
use attachments or accessories not recom-
mended for use with this product. Any such
use could result in possible serious injury.
0
in wood ................................................................3-1/8"
0
in mild steel..............................................................3/8"
LENGTH OF
WIRE GAUGE REQUIRED
EXTENSION CORD
(AMERICAN WIRE GAUGE)
0-25 FEET
26-50 FEET
51-100 FEET
120V LINES
NO.16
NO.14
NO.12
Advertisement
