Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for HAMPTON BAY Havenville
Summary of Contents for HAMPTON BAY Havenville
- Page 2 Havenville by Hampton Bay ®...
-
Page 3: Table Of Contents
52” Havenville Thank you for purchasing our ceiling fan. This product has been manufactured with the highest standards of safety and quality. Ceiling Fan by Hampton Bay Date Purchased Table of Contents Store Purchased Safety Rules ....1 322-771 Model No. -
Page 4: Safety Rules
Safety Rules - Read and Save These Instructions To reduce the risk of electric shock, insure electricity has been turned off After making electrical connections, spliced conductors should be turned at the circuit breaker or fuse box before beginning. upward and pushed carefully up into outlet box. The wires should be spread apart with the grounded conductor and the equipment-grounding All wiring must be in accordance with the National Electrical Code conductor on one side of the outlet box and ungrounded conductor on the... -
Page 5: Unpacking Your Fan
Unpacking Your Fan Unpack your fan and check the contents. You should have the following items: Set of blades (5) Fan motor assembly Blade Attachment Hardware 3/16"×7.5mm Screws (16PCs.) Ceiling canopy Blade holders (5) Fiber Washers (16 PCs.) Hanger bracket Mounting plate Canopy cover Switch housing... -
Page 6: Installing Your Fan
Installing Your Fan Provide Strong Support Figures 1~3 are examples of different ways to Tools Required mount the outlet box. Phillips screwdriver, straight slot screwdriver, step ladder and wire cutters. Recessed Ceiling Outlet Box Mounting Plate Figure 3 Mounting Options Outlet Box Note: You may need a longer downrod to If there isn't an existing UL listed mounting box,... - Page 7 Hanging the Fan WARNING Cross Pin FAILURE TO PROPERLY INSTALL COTTER PIN Hanger Ball AS NOTED IN STEP 5 COULD RESULT IN FAN REMEMBER to turn off the power. Follow the LOOSENING AND POSSIBLY FALLING. steps below to hang your fan properly. Downrod Remove the canopy cover from the canopy by turning the cover counter clockwise.
-
Page 8: Installing Fan To The Electrical Box
Slip coupling cover, canopy cover and canopy Installing Fan to UL Listed Outlet Box onto downrod. Carefully reinstall hanger ball the Electrical Box onto rod being sure that cross pin is in correct position, set screws are tighten and wires are not twisted. - Page 9 REMEMBER to disconnect the power. Conductor (available at your Hampton Bay Retailer, the wire color out of wall control may vary, see If you feel you do not have enough electrical wall control's installation manual for correct wiring knowledge or experience, have your fan Outlet Box wire connections.)
- Page 10 SUPPLY CIRCUIT SUPPLY CIRCUIT Ground Ground Conductor Conductor Outlet Box Outlet Box Green Green Ground Ground Lead Lead Ground to Ground to Downrod Downrod Figure 13 Figure 14...
-
Page 11: Finishing The Fan Installation
Finishing the Fan Installation Outlet Box Tuck connections neatly into ceiling outlet box. Hanger Bracket Slide the canopy up to mounting bracket and place the key hole on the canopy over the screw on the mounting bracket, turn canopy until it locks in place at the narrow section of the key holes. (Fig. 15) Screws Align the circular hole on canopy with the remaining hole on the mounting bracket, secure by Canopy... -
Page 12: Attaching The Fan Blades
Attaching the Fan Blades CAUTION MOTOR IS SHIPPED WITH RUBBER PACKING MOUNTS TO PREVENT MOVEMENT DURING TRANSPORTATION. REMOVE RUBBER PACKING MOUNTS FROM MOTOR Rubber Packing Mounts ASSEMBLY AND DISCARD PRIOR TO ATTACH- ING BLADE ARMS. (FIG. 16) Screws Figure 16 Attach the fan blades to the blade holders using the screws and fiber washers provided, tighten screws securely. -
Page 13: Blade Balancing
Blade Balancing The following procedure should correct most fan wobble. Check after each step. Touching Ceiling Check that all blade and blade bracket screws are secure. Most fan wobble problems are caused when blade levels are unequal. Check this level by selecting a point on the ceiling above the tip of one of the blades. -
Page 14: Installing The Light Kit
Carefully push all wires back into the switch Installing the Mounting Installing the housing, then install the light kit assembly onto Plate the mounting plate with 3 screws provided. Be Light Kit sure to tighten all screws. (Fig. 22) Remove 1 of 3 screws from the mounting ring Remove the lock ring from the socket by and loosen the other 2 screws. -
Page 15: Fan Without Light Kit
Fan without Light Kit (Optional) CAUTION BEFORE STARTING INSTALLATION, DISCON- NECT THE POWER BY TURNING OFF THE CIRCUIT BREAKER OR REMOVING THE FUSE AT FUSE BOX. TURNING POWER OFF USING THE FAN SWITCH IS NOT SUFFICIENT TO PREVENT ELECTRIC SHOCK. Holding the switch housing under your fan, snap the wire connection plugs together . -
Page 16: Operating Your Fan
Operating Your Fan Cool weather - (Clockwise direction) An upward NOTE air flow moves warm air off the ceiling are as WAIT FOR FAN TO STOP BEFORE REVERSING shown in Figure 25. This allows you to set your THE DIRECTION OF THE BLADE ROTATION. heating unit on a lower setting without affecting your comfort. -
Page 17: Care Of Your Fan
Care of Your Fan Troubleshooting PROBLEM SOLUTION Here are some suggestions to help you maintain your fan. Fan will not start Check main and branch circuit fuses or breakers. Because of the fan's natural movement, some Check line wire connections to the fan and switch wire connections in connections may become loose. -
Page 18: Specifications
Specifications FAN SIZE SPEED VOLTS AMPS WATTS N.W. G.W. C.F. 0.22 9.29 58.62 1574.47 9.90 kgs 11.04 kgs 0.38 28.71 109.80 3112.88 52" MED. 2.14' (21.78 lbs) (24.29 lbs) 0.55 66.97 167.67 5010.42 HIGH These are approximate measures. They do not include Amps and Wattage used by the light kit . Distributed by Home Depot U.S.A., Inc. -
Page 19: Warranty Information
Lifetime Limited Warranty (lifetime warranty on motor) The Hampton Bay warrants the fan motor to be free from defects in workmanship and material present at time You must present a copy of the original purchase receipt to obtain warranty of shipment from the factory for a period of lifetime after the date of purchase by the original purchaser.